Dimplex WMS718N Manuel utilisateur

These feet should only be used when it is not intended to fix the appliance to the wall.

NOTE :- When the feet have been fitted, the appliance MUST be positioned against a wall on

a firm surface before building in the storage heater bricks.

DO NOTATTEMPT TO MOVE THE HEATER, UNDER ANY CIRCUMSTANCES, ONCE

THE BRICKS ARE FITTED

INSTRUCTIONS FOR FITTING

OPTIONAL FLOOR STANDING FEET

MODELS: WMX/S718N, WMX/S724N, HSX/DA18N & HSX/DA24N ONLY

1. Remove the outer wrap packing of the heater, ensuring the end packing is left on the heater.

2. Rotate the heater so as it is upside down and the outer

front is facing away from the installer. See fig 1.

3. Place an M4 taptite screw as supplied in the fixing kit in

each of the drawn holes A and B. See fig 2A.

4. Tighten both the screws until they are approximately half

way into the base of the heater.

5. Taking one of the floor standing feet and viewing as

shown in fig 2B, rotate the foot to position Keyhole A

over the taptite screw located in hole A.

CONTENTS TOOLS REQUIRED

2 x Floor Standing Feet Pozi-drive Screwdriver

4 x No. 6 x 3/8” Self Tapping Screws Electric Drill

2 x M4 Taptite Screws

1 x 2.6mm Ø drill bit

KEYHOLE B

FIG. 2B TOP VIEW OF HEATER

FRONT OF HEATER

TOP VIEW OF FEET

FRONT OF FOOT

KEYHOLE A

FIG. 1 FRONT OF HEATER

FIG. 2A

TOP VIEW OF HEATER

FRONT OF HEATER A B

A B

83816 Issue 1 : 01.98

6. Slide the foot across until the

screw is located in the smaller

sectionofthekeyhole.Seefig 3A.

7. Using a pozi-drive screw driver,

locate the taptite screw through

the hole provided as shown in Fig

3B.

8. Note:At this stage thefeetmust

be parallel and pointing for-

wards. Tighten both screws se-

curely, ensuring they are located

correctly in the keyholes.

9. Observe holes C,D,E, and F as

shown in fig 4, at the rear fixing

bracket of the floor standing foot.

10. Taking the2.6mmdrill bit supplied

in the fixing kit, drill four holes

through the body of the heater us-

ing holes C,D,E and F as a tem-

plate. Do not allow the drill bit to travel more than 5mm into the heater. Please

ensure the heater is gripped firmly and the feet remain in position.

11. Secure the back of the feet to the heater by fixing the four No.6 x 3/8" self tapping

screws provided through the holes C,D,E and F.

12. With the feet securely fixed to the heater, rotate the heater onto its feet and then re-

move the side packing.

13. Cable entry may be effected from either the right or the left side of the unit, but the cable

should be routed around the back of the foot and then fed through the appropriate

retaining clips.

FIG. 4 FRONT OF HEATER

FIG. 3A

FIG. 3B

FRONT OF HEATER

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dimplex Chauffage

Dimplex

Dimplex OFRC10ECCb Manuel utilisateur

Dimplex

Dimplex CXL N Instructions de montage

Dimplex

Dimplex RPX100N Manuel utilisateur

Dimplex

Dimplex Cadiz Eco CDR2T Manuel utilisateur

Dimplex

Dimplex DHCER20 Manuel utilisateur

Dimplex

Dimplex SAF6 Series Manuel utilisateur

Dimplex

Dimplex BFH24BWSR Manuel

Dimplex

Dimplex FX 20E IPX4 Manuel utilisateur

Dimplex

Dimplex EvoRad15BT Manuel utilisateur

Dimplex

Dimplex DHCHT20M Manuel utilisateur

Dimplex

Dimplex DXUC2B Manuel utilisateur

Dimplex

Dimplex XLE050 Guide de référence

Dimplex

Dimplex XLE Series Manuel utilisateur

Dimplex

Dimplex PLX050E Manuel utilisateur

Dimplex

Dimplex XMC712N Manuel utilisateur

Dimplex

Dimplex LC Series Manuel utilisateur

Dimplex

Dimplex RD 909 TS/LCD Manuel utilisateur

Dimplex

Dimplex OFX075l OFX100 Manuel utilisateur

Dimplex

Dimplex CXL Manuel utilisateur

Dimplex

Dimplex AC3RE Manuel utilisateur

Dimplex

Dimplex QXD1500ND Manuel utilisateur

Dimplex

Dimplex DHCER20FE Manuel utilisateur

Dimplex

Dimplex QM050 Manuel utilisateur

Dimplex

Dimplex FXL18N Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur