Dimplex RAL15-AU Manuel utilisateur

RAIL SUITE RAL15-AU

8/ 54717/0 Issue 1

The product complies with the European Safety Standards and the European Standard Electromagnetic Compatibility (EMC). These cover the essential requirements

of EEC Directives.

1100 280

900

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

General

Unpack the heater carefully and retain the

packaging for possible future use, in the

event of moving or returning the re to your

supplier.

The re incorporates a ame effect, which

can be used with or without heating, so that

the comforting effect may be enjoyed at

any time of the year. Using the ame effect

on its own only requires little electricity.

Before connecting the heater check that the

supply voltage is the same as that stated on

the heater.

Please note: Used in an environment where

background noise is very low, it may be

possible to hear a sound which is related

to the operation of the ame effect. This

is normal and should not be a cause for

concern.

Electrical Connection

WARNING: THIS APPLIANCE MUST BE

EARTHED

This heater must be used on an AC ~ supply

only and the voltage marked on the heater

must correspond to the supply voltage.

Before switching on, please read the safety

warnings and operating instructions.

Important Safety Advice

When using electrical appliances, basic

precautions should be followed to

reduce the risk of re, electric shock, and

injury to persons, including the following:

If the appliance is damaged, check

immediately with the supplier before

installation and operation.

Do not use this appliance in the

immediate surroundings of a bath,

shower or swimming pool.

Do not use outdoors.

This appliance must not be located

immediately above or below a fixed

socket outlet or connection box.

WARNING: The appliance carries

the Warning Symbol indicating that

it must not be covered or has a Do

not cover label. Do not cover or

obstruct in any way the heat outlet grille

located above the ame window on the

appliance Overheating will result if the

appliance is accidentally covered. Do

not place material or garments on the

appliance, or obstruct the air circulation

around the appliance, for instance by

curtains or furniture, as this could cause

overheating and a re risk.

In the event of a fault unplug the heater.

Unplug the appliance when not required

for long periods.The supply cord must

be placed on the right hand side of

the heater away from the heat outlet

underneath the appliance.

This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use

of the appliance by a person responsible

for their safety.

Children should be supervised to ensure

they do not play with the appliance.

Prior to cleaning or other maintenance,

the appliance must be disconnected

from the supply mains.

The appliance must be positioned so that

the plug is accessible.

If the supply cord is damaged it must be

replaced by the manufacturer or service

agent or similarly qualified person in

order to avoid a hazard.

CAUTION: In order to avoid a hazard due

to inadvertent resetting of the thermal

cut-out, this appliance must not be

supplied through an external switching

device, such as a timer, or connected

to a circuit that is regularly switched on

and off by the utility.

CAUTION - Some parts of this product

can become very hot and cause burns.

Particular attention has to be given

where children and vulnerable people

are present.

Icon Function Description

APower Press to turn unit Off or On.

• Unit Off

Press to turn everything Off. Press again to turn unit On with previous settings.

• Unit On

Press to turn unit On with previous settings.

- If the flame effect was On, the flame will turn on and the previous heat setting will

be activated (On or Off). Display will show current heater temperature setting and

after 2 sec displays the room temperature.

- [remote only] If the flame effect was Off, the previous heat setting will be

activated (On or Off).

- [panel only] If the flame effect was Off, the flame will turn on and the previous

heat setting will be activated (On or Off)

BHeat • Heat On

Press to turn heat On (indicated by 1 short beep). Display will show current heater

temperature setting and after 2 sec displays room temperature. Use the Temp icon

to change the heater temperature setting.

• Heat Off

Press to turn heat Off (indicated by 1 short beep).

NOTE: After the heater is switched off, the fan will continue on for 60 seconds before turning

off.

CTemp Press multiple times to raise the heater temperature in 1oF (1oC) increments. Display

will show current temperature. Temperature range is 62o-78oF (17o-26oC).

This feature is active whenever the heat is enabled.

DFlame Speed Press multiple times to toggle through flame speeds (minimum, medium, maximum).

Display will show current speed number (F1, F2, F3 respectively).

EColor Themes Press multiple times to change the media and flame base colors. This feature is

active only when the flame effect is On. Display will show theme (t0, t1, t2, etc.)

XHD28L, XHD26L or XHD23L

(Log Unit) themes:

• Theme t0 - no flame

• Theme t1 - Natural (flame base off)

• Theme t2 - Red Highlights (flame base red/orange)

• Theme t3 - Blue Highlights (flame base blue)

FBrightness Press to change the flame and logs brightness. Display will show b3, b1, b2

respectively.

• High

• Low

• Medium

GFlame Press to turn the flame effect On. Press again to turn the flame effect Off.

HTimer Press multiple times to change the sleep timer by 0.5 hr from 0.5 hr to 8 hr before

turning off. Press again, the remaining time on the timer displays.

User Modes:

Mode Name /Discription Action (Actions cannot be input by remote control)

Change Celsius (0C) to

Fahrenheit (0F)

Press both Temp Button ( ) and flame speed( ) on the unit and hold until beep is

heard and display flashes. (To revert back to Celsius repeat this action)

Disable / Enable Heat

Options

Hold both Heat Button ( ) and Temp Button ( ), on the unit, for 2 seconds, when the

heater has been disabled the display will read “--” and beep. To enable heat repeat this

action.

Controls: See Fig. 2

Resetting the Temperature Cutout Switch

Should the heater overheat, an automatic cutout will turn the heater off. It will not come back on without being reset.

To reset the cutout switch, unplug the unit and wait 5 minutes before plugging it back in.

Remote Control- See Fig. 2

The maximum range of use is ~ 9 metres.

NOTE: It takes time for the receiver to respond to the transmitter.

NOTE: The reciever for the remote control is located in the display, aim the remote control in this direction when inputting

commands.

Do not press the buttons more than once within two seconds for correct operation.

Battery Information

1. To activate the remote control remove the clear battery isolation strip at the base of the remote control, which is used

to ensure your remote control reaches you fully charged.

2. To replace the remote control battery, turn over the remote control, and follow the diagram embossed on the remote

control

Tipping Restraint- See Fig. 3

WARNING: FALLING OR TIPPING APPLIANCES CAN CAUSE INJURY OR DEATH OF YOUNG CHILDREN, PLEASE ENSURE CHILDREN

DO NOT CLIMB, HANG OR STAND ON THIS PRODUCT.

WARNING: THE APPLIANCE IS PROVIDED WITH A TIPPING RESTRAINT, THIS RESTRAINT IS NOT A SUBSTITUTE FOR PROPER ADULT

SUPERVISION. THIS RESTRAINT MAY PROVIDE PROTECTION AGAINST TIPPING FURNITURE. DO NOT ALLOW CHILDREN TO CLIMB

ON FURNITURE. FAILURE TO DETACH THIS RESTRAINT BEFORE MOVING FURNITURE MAY RESULT IN INJURY AND DAMAGE.

This product is provided with a ‘Tipping Restraint Kit’ as shown in Fig 3, to prevent the product accidentally tipping. Instructions

are supplied with this kit please follow these instructions carefully. This accessory is intended to improve the safety of the

the product.

Thermal Safety Cut-out

The built-in overheat cut-out, switches off the appliance automatically in the event of a fault! Should this occur switch off

the appliance or disconnect the mains plug from the socket.

Remove any obstructions which may have caused the overheating. After a short cooling down phase, the appliance is

ready for use again! If the fault should occur again, contact your local dealer!

WARNING: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be

supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and

off by the utility.

Mounting Glass frame- See Fig. 4

Product comes with glass frame not xed to re, but packed separately to the re in its own packing.

To x frame the hooks on both side at the top need to be aligned up with corresponding slots on both sides of the re.

When hooked in place the frame hangs vertical covering the re.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.

Light Emitting Diode

This re is tted with LED (Light Emitting Diode) lamps. These LED lamps are maintenance-free and should not require replacing

during the life of the product.

Cleaning

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.

For general cleaning use a soft clean duster – never use abrasive cleaners. The glass viewing screen should be cleaned

carefully with a soft cloth.

DO NOT use proprietary glass cleaners.

To remove any accumulation of dust or uff the soft brush attachment of a vacuum cleaner should occasionally be used

to clean the outlet grille of the fan heater.

WARNING: do not operate the product without the grille and outer glass in position as this may effect the operation of the

heater.

Recycling

For electrical products sold within the European Community. At the end of the electrical products useful life it

should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local

Authority or retailer for recycling advice in your country.

After Sales Service

Should you require after sales service or should you need to purchase any spares, please contact the retailer from whom

the appliance was purchased or contact the service number relevant to your country on the warranty card.

Please do not return a faulty product to us in the rst instance as this may result in loss or damage and delay in providing

you with a satisfactory service. Please retain your receipt as proof of purchase.

Autres manuels pour RAL15-AU

Table des matières

Autres manuels Dimplex Chauffage

Dimplex

Dimplex OFRB14 Manuel utilisateur

Dimplex

Dimplex RCH5031CXW Manuel utilisateur

Dimplex

Dimplex LPC Series Manuel utilisateur

Dimplex

Dimplex DGR32WNG Manuel utilisateur

Dimplex

Dimplex EF12 Series Manuel utilisateur

Dimplex

Dimplex GFP 100EW Manuel utilisateur

Dimplex

Dimplex DHCER24E Manuel utilisateur

Dimplex

Dimplex CKHA Series Guide de configuration

Dimplex

Dimplex CAB10A Manuel utilisateur

Dimplex

Dimplex EUH-B Series Manuel utilisateur

Dimplex

Dimplex PPC Series Manuel utilisateur

Dimplex

Dimplex EVORAD2E Manuel utilisateur

Dimplex

Dimplex Q-Rad Series Manuel utilisateur

Dimplex

Dimplex RX TI RB Manuel utilisateur

Dimplex

Dimplex PLXE Series Manuel utilisateur

Dimplex

Dimplex Comfort 2NC6 L Series Guide de l'utilisateur

Dimplex

Dimplex 403TS Manuel utilisateur

Dimplex

Dimplex RFF Series Manuel utilisateur

Dimplex

Dimplex DHCER20 Manuel utilisateur

Dimplex

Dimplex Studio 842 Manuel utilisateur

Dimplex

Dimplex Studio G DXSTG25 Manuel utilisateur

Dimplex

Dimplex DHCER24M Manuel utilisateur

Dimplex

Dimplex Coldwatcher MPH 500 Manuel utilisateur

Dimplex

Dimplex EWa-C Series Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur