Dimplex Q-Rad QRAD050RF Manuel utilisateur

These instructions should be read carefully

and retained for future use. Note also the

information presented on the appliance.

INSTRUCTION MANUAL

Installation and Operating

08/82904/0 (300001427) ISSUE: 3 Series: G

Q-Rad Electric Radiator

Models: QRAD050RF / QRAD075RF / QRAD100RF

QRAD150RF / QRAD200RF

IMPORTANT

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR

FUTURE REFERENCE. Note also the information presented on the appliance

IMPORTANT SAFETY ADVICE

When using electrical appliances, basic precautions should always be followed to reduce

the risk of ﬁre, electrical shock, and injury to persons, including the following:

IMPORTANT: The wall bracket supplied with the appliance must be used.

WARNING: DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF A

BATH, A SHOWER OR A SWIMMING POOL.

IMPORTANT: If the heater is installed in a room containing a bath or shower, it must

be installed so that switches and other controls cannot be touched by a person using

a bath or shower.

Do not use outdoors.

Do not locate the heater immediately below a ﬁxed socket outlet or connection box.

WARNING: In order to avoid overheating, do not cover the heater. Do not place material

or garments on the heater, or obstruct the air circulation around the heater, for instance

by curtains or furniture, as this could cause overheating and a ﬁre risk.

NEVER cover or obstruct in any way the heat outlet slots at the top of the heater or the

air inlet slots in the base of the heater.

The heater carries a warning ‘DO NOT COVER’ to alert the user to the risk of ﬁre that

exists if the heater is accidentally covered.

CAUTION: Some parts of this product can become very hot and cause burns. Particular

attention has to be given where children and vulnerable people are present.

This appliance can be used by children aged from 8 years and above and by persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

Children of less than 3 years should be kept away unless continuously supervised. Children

aged from 3 years and less than 8 years shall only switch on/o the appliance provided

that it has been placed or installed in its intended normal operating position and they

have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children aged from 3 years and less than 8

years shall not plug in, regulate and clean the appliance or perform user maintenance.

Note that due care and consideration must be taken when using this heater in series

with a thermal control, a program controller, a timer or any other device that switches

on the heat automatically, since a ﬁre risk exists when the heater is accidentally covered

or displaced.

If the supply cord is damaged it must be replaced by the manufacturer or service agent

or a similarly qualiﬁed person in order to avoid a hazard.

WARNING: Servicing and product repairs should only be undertaken by the manufacturers

approved service agent or a similarly qualiﬁed person, using only exact manufacturer

approved spare parts.

WARNING: THIS APPLIANCE MUST BE EARTHED

The electrical installation must be carried out by a competent electrician, and be in strict

accordance with the current I.E.E. Regulations for Electrical Equipment in Buildings. The

wires in this mains lead are coloured in accordance with the following code:

GREEN AND YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

The heater is ﬁtted with a length of ﬂexible cable type H05VV-F size 3 x 1.0mm2 for

connection to the ﬁxed wiring of the premises through a suitable connection box

positioned adjacent to the heater.

A means for disconnection must be incorporated in the ﬁxed wiring of the premises in

accordance with the wiring rules. The supply circuit to the heater must incorporate a

double pole isolating switch having a contact separation of at least 3mm.

DO NOT USE THIS HEATER IF IT HAS BEEN DROPPED.

DO NOT USE IF THERE ARE VISIBLE SIGNS OF DAMAGE TO THE HEATER.

USE THIS HEATER ON A HORIZONTAL SURFACE, OR FIX IT TO THE WALL AS

APPLICABLE.

WARNING:

Do not use this heater in small rooms when they are occupied by persons

not capable of leaving the room on their own, unless constant supervision is provided.

WARNING: To reduce the risk of ﬁre keep textiles, curtains or any other ﬂammable

material a minimum distance of 1 metre from the air outlet.

Supplementary Earth Bonding

Should Equipotential Earth Bonding be required the earthing conductor in the supply

cord is deemed to provide the supplementary bonding connection (see Regulation

544.2.5, 18th Edition I.E.E. Wiring Regulations).

Please note that lit cigarettes, candles and oil burners, combined with the convection

eect of electric heaters can cause soot deposits to build up on the surface directly

above and to the sides of the heater. This is not a fault of the heater. Extensive burning

of candles or smoking in the operating environment of this product can produce heavy

discolouration within a few months of use.

This product meets the Ecodesign requirements for an electric ﬁxed local space heater. Commission Regulation

(EU) 2015/1188.

Energy Related Product Directive

Technical Details

Type of heat output/ room temperature control

With electronic room temperature control

Yes

Electronic room temperature control plus week timer

Yes

With open window detection

Yes

With adaptive start control

Yes

Model Identiﬁer(s):

QRAD050RF

QRAD075RF

QRAD100RF

QRAD150RF

QRAD200RF

Norninal heat output Pnom 0.5kW 0.75kW 1 kW 1.5kW 2.0kW

Height (mm) 546 546 546 546 546

Width (mm) 513 513 675 756 918

Depth (mm) 105 105 105 105 105

Minimum heat

output (indicative) Pmin N.A N.A N.A N.A N.A

Maximum continuous

heat output Pmax,c 0.5 0.75 1 1.5 2

Auxiliary Electricity Consumption

At nominal heat output elmax 0.00 0.00 0.00 0.00 0.00

At minimum heat output elmin 0.00 0.00 0.00 0.00 0.00

In standby mode elSB

<0.0005 <0.0005 <0.0005 <0.0005 <0.0005

With open window detection

Yes

With adaptive start control

Yes

Contact details

Glen Dimplex Heating and Ventilation

Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF

Tel: 0344 879 3588

All Models

Controls

Digitally controlled, Electronic Thermostat accurate to (±0.2oC)

Timer modes:

7 Day Programmable User Timer, Out All Day, Home All Day, Away Mode

Continuous heat modes:

Eco, Manual, Frost Protect, Setback

Controller UI

• Open window detection, Adaptive-start

• Advance time period

• Adjustable max setpoint range (7-30°C)

• Bluetooth for software updates

• Child Lock & Landlord Lock (PIN-based)

Construction • Durable epoxy-polyester powder coated steel casing with louvered forward facing grille

• Advanced controls with capacitive sense technology for total ﬂexibility of heating

Colour/ Finish

Metal Chassis, Air Outlet Grille & Control Moulding - Trac White (RAL 9016)

Element Compact, ﬁnned, mineral ﬁlled sheathed element

Installation • H-frame wall bracket

Safety • Thermal cut-out. Auto reset type

• Overheat detection

IP Rating IP24

Battery

3.3V coin cell battery to backup real time clock. Battery life >5 years.

Supply

1.3 metres ﬁtted, 3 core for fused spur installation, 1/N/PE ~230-240 V, 50Hz

Class I, with earth wire

Colour / Finish Metal Chassis, Air Outlet Grille & Control Moulding - Trac White (RAL 9016)

Approvals UKCA, CE & BEAB

Guarantee 2 years

Country of Origin United Kingdom

Manufacturer Glen Dimplex Heating & Ventilation

(Glen Dimplex UK Ltd.)

The heater is designed for wall mounting using the wall bracket supplied. It should only be

operated when in the upright position as shown - see Fig. 1 and Fig. 2. All models are splash

proof to IP24 standard and may be used in bathrooms, however not in the immediate vicinity

of baths, showers, water connections, wash basins or swimming pools. Before connecting the

heater check that the supply voltage is the same as that stated on the heater.

IMPORTANT – The wall bracket supplied with the appliance must be used. The heater should be

positioned observing the minimum clearances stated around the heater - see Fig. 1 and Fig. 2.

DO NOT locate the heater immediately below a ﬁxed socket outlet or connection box.

1. Remove wall mounting bracket from the back of the heater by depressing the spring latch

at the top of each bracket - see Fig. 3.

2. Fix the wall bracket securely to the wall through the four screw holes provided.

3. Present the heater to the wall bracket, and engage lower slots in the back with bracket.

4. Raise the heater to upright position and push the heater onto bracket to engage top latches.

General

Wall Mounting

Model(s) Watt (kW) A (mm)

QRAD050RF 0.50 kW 513

QRAD075RF 0.75 kW 513

QRAD100RF 1.0 kW 675

QRAD150RF 1.5 kW 756

QRAD200RF 2.0 kW 918

105 mm

Shelf

300 mm

Minimum front clearance

Fig. 1

150 mm (Min)

546 mm

Model (s) B (mm)

QRAD050RF 225

QRAD075RF 225

QRAD100RF 387

QRAD150RF 468

QRAD200RF 630

260 mm (Min)

275 mm

294 mm

(Min)

150 mm (Min)

Fig. 2

Fig. 3

A setup wizard will display when the product is powered

on for the ﬁrst time. This will set the following:

• Time, Date, Daylight Savings Time

• Sound On/O

For information on using the Heaters controls, refer to page

9. The Heater will then take the User to the Home Screen

with the ‘Out All Day’ Timer Mode active.

First Time Power-On

Operation Manual

Important

During initial heat-up, some odour

may be emitted due to the newness of

materials used in manufacture. This is

normal and will disappear after a short

period of use. It is however advisable

to keep the room well ventilated.

The controls are located on top of the heater. This consists of a display screen and six touch sensitive buttons.

WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT

IN INJURY AND/OR DAMAGE.

1Display Screen

2‘Menu’ Button

3‘Back’ Button

4‘Up and Down’ Arrows

5‘Enter’ Button

6‘Advance’ Button

7Heating Status

The heater is ﬁtted with an adjustable thermostat enabling the room temperature to be controlled. The minimum

room temperature is 7°C. The maximum temperature is set to 30°C. A temperature of 21°C is a common comfortable

room temperature.

Out All Day

57 3

2 46

21°C

Heating On

NOTE:

Your heater may produce some noise during

operation. This noise is caused by the expansion

and contraction of the element as it changes

temperature, and is normal for this type of

product. Whilst the noise produced is usually

very quiet, certain environmental factors can

make it more noticeable, such as hard ﬂooring

or minimal furnishings If you believe that the

expansion noise is excessive, please contact us.

NOTE:

Should the heater fail to operate,

this may be caused by the room

temperature being higher than the

thermostat setting.

The heater controls can be easily adjusted by using the six buttons on the User Interface.

1. The Home Screen shows the options available at each stage of adjustment.

Here the current target temperature (setpoint) is displayed along with the

mode of operation. Any use of the Advance function will be displayed here,

and pressing Enter will show the functions which are enabled.

The currently active mode of operation is displayed at the top of the screen

e.g. ‘Out All Day’ timer.

When the heater is trying to achieve or maintain a room temperature, ‘Heating

On’ will be displayed, otherwise, ‘Heating O‘ will be displayed, during Timer

modes only.

NB: ‘Heating ON / Heating OFF’ will not be displayed in Manual, ECO or

Frost Protect modes.

When the controller buttons have not been pressed for a long period of time, the display will ‘sleep’ and the text will

disappear. The heater is still on and active in whatever Mode it was set to.

2. Menu - Displays the Main Menu;

- Boost – Activate Boost Mode

- Modes - Set the mode of operation.

- Settings – Time/Date, Temperature units etc.

3. Back returns to the previous screen.

4. The Up and Down buttons are used to navigate through the menus and adjust the required room temperature on

the main screen. The screen colour changes based on the temperature selected, showing deep blue through to

bright red.

5. Enter is used to enter sub menus and to conﬁrm actions.

6. The Advance button is only used when a Timer Mode is active, it allows the timer schedule to be changed temporarily

by forcing a Heating On period to begin or end early. For more information, see page 13.

Out All Day

21°C

Heating ON

Timer Modes oer the most ecient mode of operation for a predictable heat demand. Additional functions such as

‘Advance’ and ‘Boost’ allow the User to make temporary adjustments to timer schedules for a more ﬂexible operation.

Each timer is broken down into 4 deﬁnable ‘Heating On’ time periods and temperatures per day, for each day of

the week. Each day consists of a 24-Hour period, starting and

ﬁnishing at midnight.

‘Heating On’ periods are times when the heater is trying to achieve

and maintain the target room temperature.

It is possible to change the Target Temperature of a Heating On

period when that period is active. This will temporarily adjust the

Target Temperature for just that instance and will not permanently

modify the settings for the timer in use.

NOTE:

If Adaptive Start is enabled, the heater will maintain the room at the required temperature

for the duration of the heating period. To achieve this, the heater will begin heating the room

before the start of the heating period to ensure the room is at the required temperature when

the period starts.

If Adaptive Start (AS) is disabled, the heater will not operate until the beginning of the heating

period. This should be taken into consideration when setting the heating periods.

See page 16 for instruction on enabling/disabling Adaptive Start.

ADVANCE

BACK

ENTER

Out All Day

21°C

Heating ON

Timer Modes

Available Timer Modes

To choose a timer mode, press Menu from the home screen. Use the arrow keys to highlight ‘Modes’, then press

Enter to select. ‘Timer Mode’ should be highlighted, press Enter to select.

A list of Timer Modes will be shown. Their default settings are shown in the table below.

Highlight one of the available Timer Modes using the arrow keys. Press Enter to select

For User Timer, Home All Day and Out All Day, three choices will be available:

Select - This option will activate the timer

Modify - This option allows the timer’s Heating On times and Target Temperatures to be modiﬁed

Preview - This option displays the timer’s conﬁguration. This is useful to quickly check the timer without being

able to change any values

ADVANCE

BACK

ENTER

Manual

21°C

Heating ON

Period 1 Period 2 Period 3 Period 4

User Timer 06:30 – 09:30 21 11:00 – 13:00 21 15:00 – 17:00 21 18:00 – 22:00 21

Home All Day 08:00 – 21:00 21 21:00 – 21:00 21 21:00 – 21:00 21 21:00 – 21:00 21

Out All Day 07:00 – 08:30 21 17:30 – 22:00 21 22:00 – 22:00 21 22:00 – 22:00 22

Away Mode Away Mode does not operate in the same way as the other Timers.

See section ‘Away Mode’ on page 11

ADVANCE

BACK

ENTER

Main Menu

Boost

Modes

Settings

ADVANCE

BACK

ENTER

Main Menu

Timer Mode

Manual

Eco Mode

Frost Protect

ADVANCE

BACK

ENTER

Timer Mode

User Timer

Home All Day

Out All Day

Away

ADVANCE

BACK

ENTER

User Timer

Select

Modify

Preview

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dimplex Chauffage

Dimplex

Dimplex FX 20VL Manuel utilisateur

Dimplex

Dimplex QXD1500 Manuel utilisateur

Dimplex

Dimplex QM070 Quantum Manuel utilisateur

Dimplex

Dimplex LPC Series Manuel utilisateur

Dimplex

Dimplex PLXE Manuel utilisateur

Dimplex

Dimplex H 260E Manuel utilisateur

Dimplex

Dimplex EF 10/20 S Manuel utilisateur

Dimplex

Dimplex OFRC10 Manuel utilisateur

Dimplex

Dimplex XL6N Manuel utilisateur

Dimplex

Dimplex DXFF20TS Manuel utilisateur

Dimplex

Dimplex XL6N Manuel utilisateur

Dimplex

Dimplex OFRB7 Manuel utilisateur

Dimplex

Dimplex VFE 20 Manuel utilisateur

Dimplex

Dimplex XHD23L-AU-RL Manuel utilisateur

Dimplex

Dimplex FXL12i Manuel utilisateur

Dimplex

Dimplex PLX 3000 Manuel utilisateur

Dimplex

Dimplex EPX 500 Manuel utilisateur

Dimplex

Dimplex FW 550S Manuel utilisateur

Dimplex

Dimplex LC Series Manuel utilisateur

Dimplex

Dimplex FX 20V Manuel utilisateur

Dimplex

Dimplex XLS Manuel utilisateur

Dimplex

Dimplex FPE 050E Manuel utilisateur

Dimplex

Dimplex ROF2T Manuel utilisateur

Dimplex

Dimplex ARLWP800TI Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur