3. Installation Guide
This product left the place of manufacture in perfect condition.
In order to maintain this condition and for safe operation, the user must always follow
the instructions and safety warnings described in this user manual.
Safety Warning!
General
- This product must be installed by a qualified and competent professional.
- When working on the fixture, heat resistant gloves should be worn to provide
adequate user protection.
- Do not work on the product with wet hands.
- Always disconnect the power supply before attempting to maintain or service
the equipment.
- Always operate the equipment as described in this user manual.
- Do not stand close to the equipment and stare directly into the LED light source.
- Make sure that all parts of the equipment are kept clean and free of dust which
should be carried out as part of a maintenance cycle that’s appropriate for the
installation location of the product.
- When transferring the product, it is advisable to use the original packaging in
which the product left the factory.
- Shields, lenses, ultraviolet screens and pressure release valves should be
changed if they have become damaged to such an extent that their
effectiveness is impaired.
- The lamp (LED) should be changed if it has become damaged or thermally
deformed.
- The power supply (PSU), DMX/RDM driver and LED drivers should be changed if
they fail to operate.
Installation
- A minimum distance of 0.5m must be maintained between the equipment and
any combustible surface. The mounting surface must not be combustible.
- Always ensure the supporting structure is a flat and solid surface and can
support the weight of the product and any additional wind or shear force.
The supporting structure must be capable for the installation of luminaires,
and advice must be taken from an appropriately qualified and competent person
to verify proposed mounting positions and surfaces.
- Always make sure that the equipment is installed securely and ensure all safety
anchors are installed.
- The product must be installed within well-ventilated areas.
- The Earth wire MUST ALWAYS be connected.
- Local electrical and building regulations must be followed. If in doubt, please
contact support distributor
- Avoid shaking or strong impacts to any part of the equipment.
- Always make sure that the power and data connections are connected correctly
and securely. If there is any malfunction of the equipment, contact your local
distributor immediately.
- This fixture should not be buried.
Specific Installation
- Although this product does not generate a great amount
of heat, it is recommended that you do not cover or conceal it.
- Do not route the product through walls, doors, windows,
or building structures.
- Do not roll out the product onto rough surfaces or over
sharp corners. This will scratch the PVC /silicone optics
and damage the finish of the product.
- Do not use the product if :
The outer PVC jacket is damaged
There are loose electrical connections
The wires are visible without insulation.
- Do not secure the product with staples, nails, or alike that might
damage the insulation or PVC/silicone material.
- Do not install the product on/in places where it is subject
to continuous flexing.
- Do not operate/run the product in temperatures
exceeding 55C.
- Do not operate the product over the specified voltage
or LED life degradation will be greatly increased.
- Do not leave any part of the product unsecured.
- Constant movement over time from weather can
cause damage.
- Do not reverse polarity when connecting from both ends.
This will damage the internal PCB. Always test connections
with a multi-meter before applying power.
- Do not energise the product whilst in packaging.
- The product can be cut only where marked. Look for
the “Dotted Line” or“Cutting Mark”. A cut section must have
the appropriate IP rated cap flex accessory to maintain
IP ratings.
- Cutting outside of the specified mark will damage the light.
- Do not cut while the LED flex neon is connected to power.
-- Do not install in human inhabited pools.
- During installation, violent pulling and bending are prohibited.
- Must always be used with an electrical isolation
transformer providing SELV (safety extra low voltage).
- Do not cut off the cable wire between the waterproof metal
ferrule and connector.
Waterproof metal ferrule
The light source and other electronic components
contained in this luminaire shall only be replaced by
your distributor service agent.
Caution, risk of electric shock
FAILURE TO COMPLY WITH THIS MANUAL AND LOCAL ELECTRICAL AND
CONSTRUCTION REGULATIONS MAY RESULT IN SERIOUS INJURY
OR EVEN DEATH - ALWAYS ISOLATE POWER BEFORE WORKING ON
ELECTRICAL PRODUCTS AND ENSURE ADEQUATE MEASURES ARE TAKEN
TO MECHANICALLY SUPPORT FIXTURES AT ALL TIMES.
This user manual is intended to cover as much detail as possible
for this product,and great care has been taken to ensure this and
the accuracy of the information contained within, however should
additional information or clarification be required that is not covered
within this manual or associated data sheets, or ifthere are any
uncertainties regarding the installation and operation of this product,
Distributor MUST be contacted before any work is carried out on the
fixture or associated products.
R
L
24V
+
BUSI
L
24V
Cutting mark
R
+
R
L
24V
+
4
DIMON
TECHN OLO GY
