9 Product specifications
Measuring accuracy
EDS-C 30
± 3.0mm @ 2sigma
nalog Output 0.3% of programmed span,
(12bit), incl. temperature drift and target property
Typical repeatability approx. 1.5mm, excl. possible analog error
Measuring range (on natural
surfaces)
0.05 to 30 m (matt, dark surfaces up to about
20m)
Measuring reference from front edge (see picture schematic)
approx. Ø of laser spot 6mm @5m; 7mm @10m; 15mm @30m
Time for a measurement 0.4 to approx. 4 sec
Light source Laser diode visible 620-690 nm (red)
IEC 60825-1:2001; Class 2
FD 21CFR 1040.10 and 1040.11
Beam divergence:0.16 x 0.6 mrad
Pulse duration: 0.45x10-9 s
Maximum radiant power: 0.95 mW
Laser Life Time1) typically > 50'000h @ 20°C
ESD IEC 61000-4-2 : 1995 + 1 + 2
EMC EN 61000-6-4; EN 61000-6-2
Power supply 24V DC+/-10%, 0.1 max.
Dimensions 106 x 62 x 45 mm
Operating Temperature2) -10 °C to +50 °C
Storage Temperature -40 °C to +70 °C
Environment Humidity 0...80%RH non-condensing;
no aggressive vapors
Degree of Protection P65; IEC60529, (if using protected connectors)
(protected against ingress of dust / water)
Weight 280g
Interface 1 RS-232 Interface to configure the sensor
1 program. analog output 0/4 .. 20m
1) Use minimum possi le sample rates to save laser life time
2) In case of fast continuous measurement, the max. temp. is reduced to a out 48°C
10 Error codes
No. ormat Meaning and elimination
200 @E200 Device startup information (only for error stack), successful
power on cycle or power-line not stable
203 @E203 Wrong syntax in command, prohibited parameter in command
entry or non-valid result, check command
210 @E210 Not in tracking mode, start tracking first
211 @E211 Sampling too fast for the used target, configure a slower
sampling rate (or use a more reflective target)
212 @E212 In Tracking Mode,command not executable,
Stop tracking first with s0c-command
220 @E220 Error on serial communication, check com settings
234 @E234 Distance out of range, Measure a distance within the specified
limits
252 @E252 Temperature to high, cool down the sensor
253 @E253 Temperature to low, heat up the sensor
255 @E255 Received signal to low, use a brighter target or a target plate
256 @E256 Received signal to high, use a darker target, mind reflective parts
along the laser beam
257 @E257 To much background light, cover bright light sources, use a
darker target, mind reflective parts along the laser beam
260 @E260 Strange distance result, maybe distance jump during measuring
cycle, measure to a defined target
not listed contact your Distributor or DIMETIX
11 Accessories
On our we -page www.dimetix.com you can find some helpful accessories
for the EDS-C.
- configuration ca le 3m (500 204) - Connection ca le 5m (500 205)
- Accessory for Starter Kit (500 592) - Alignment jig (500 213)
12 Quality certificate
We here y certify, that the EDS-C has een tested and complies with the
specifications as stated in this manual. The test equipment used is tracea le
to national standards, which are esta lished y our Quality Management
System. The EDS-C is made in Switzerland.
13 Labeling
Location:
The device la el is placed on the
top of the device, while the type
la el can e found on the ack.
14 Safety instructions
The following instructions are to ena le the person responsi le for the EDS-
C, and the user of the instrument, to anticipate and avoid operational
hazards.
The EDS-C is made to e integrated into technical systems. Basic technical
training is therefore essential. This device may only e operated y trained
personnel.
The person responsi le for the instrument must ensure that all users
understand these instructions and adhere to them.
If the EDS-C is part of a system, the manufacturer of such a system is
responsi le for all safety-related issues, such as the manual, la eling and
instruction.
Must not e used in aggressive, radioactive, caustic or explosive
environment.
15 Laser classification
The EDS-C produces a visi le laser eam, which emerges from the front of
the instrument. It is a Class 2 laser product in accordance with:
1) IEC60825-1 (2001) ”Radiation safety of laser products”
2) EN60825-1 (2001) ”Radiation safety of laser products”
It is a Class II laser product in accordance with:
1) FDA 21CFR 1040.10 and 1040.11 (US Department of Health and
Human Service, Code of Federal Regulations)
Laser Class 2/II products:
Do not stare into the laser eam or direct it towards other people
unnecessarily. Eye protection is normally afforded y aversion responses
including the link reflex.
WARNING: Looking directly into the eam with optical aids
( inoculars, telescopes) can e hazardous.
Precautions: Do not look into the laser eam. Make sure the laser is
aimed a ove or elow eye level. (particularly with fixed
installations, in machines, etc.).
CAUTION: Looking into the laser eam may e hazardous to the eyes.
Precautions: Do not look into the laser eam. Make sure the laser is
aimed a ove or elow eye level (particularly with fixed
installations, in machines, etc.).
16 Service information
All warranty returns and repairs have to e returned with a RMA Report
provided on our we -page www.dimetix.com . Opened devices and
devices with removed la els lose the warranty claim.
17 Disclaimer
Dimetix reserves the right to make corrections, modifications, enhancements,
improvements and other changes to its products, documentation and services at any
time and to discontinue any product or service without notice. We try to give our best
possible effort to provide you with perfect documents, but we can not guarantee for
incorrect information. Customers should obtain the latest relevant information before
placing orders and should verify that such information is up to date and complete. ll
products are sold subject to Dimetix terms and conditions of sale supplied at the time
of order acknowledgment.
Dimetix AG Tel. +41-71-353 00 00
Degersheimerstr. 14 Fax +41-71-353 00 01
Switzerland www.dimetix.com
© Copyright by Dimetix G
Fig. 2: Type Label
Fig. 1: Device label
