Digitus Biometrics CodeLock Manuel utilisateur

db CodeLock

Installation Manual

Version 1.0

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 2 of 10

Table of Contents

Determining which Lock Pawl to use .................................................................................................. 3

Overview ................................................................................................................................... 4

Securing the Door Lock - Step 1 ....................................................................................................... 4

Mount the tie-down pads to the Door and Cabinet – Step ..................................................................... 5

Route the Cable between the lock and the Remote Node / db Sentry Controller or ACM Panel – Step 3 ................. 6

Connect the cable to the Remote Node / db Sentry Controller – Step 4 ........................................................ 7

Connect the lock to 3

-party Access Panel .......................................................................................... 8

Connect the SENSE OUT to monitor the lock position (open/closed) ........................................................... 9

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 3 of 10

Determining which Lock Pawl to use

As all cabinets vary, we offer a wide range to pawls to suit the particular dimensions of your cabinet.

If new pawls are required, there is a simple measurement that needs to be taken to determine which pawl you will

need. Using the existing mechanical lock, measure the length of “H” in millimeters (mm) as shown in figure 1. Using

“H” determine which pawl is required from Table 1.

Once the correct pawl model has been determine, please contact our lock support team at +1 91 31 8175

Figure 1

Standard Pawl

Pawl with Rod Control

H (mm)

Model #

H (mm)

Model #

1000

U63

1000

U 1

1000

113

1000

U64

1000

U 3

1000

U 4

1000

U 5

1000

U 6

1000

U 7

1000

U 8

1000

U 9

1000

U30

1000

U31

1000

U33

1000

U34

1000

U35

1000

U36

1000

U37

1000

U38

1000

U39

1000

U40

1000

U41

1000

U43

1000

U44

Table 1

In most situations the pawl f

rom the existing mechanical handle can be re

used with the new lock.

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 4 of 10

Overview

If you are installing the lock into to a cabinet that already has a lock installed, remove the existing lock at this time.

Securing the Door Lock - Step 1



Secure the lock to the door using the top mounting bracket and bottom mounting bracket as show in Figure 1. Do

not over-tighten the screws in the bottom mounting bracket as this may jam the lock mechanism.

Page 3 of this document describes how to determine which pawl you will need, depending on the make and model

of cabinet.

Pay particular attention to the rotation limiter. This is installed as shown depending on whether you have a right on

left hand opening door.

Pawl

Rotation Limiter

Figure 1

Note.

Do not use an electric screwdriver to tighten the screws.

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 5 of 10

Mount the tie-down pads to the Door and Cabinet – Step 2

The ties down pads are used to secure the supplied cable that connects the lock directly to the Remote Node / db

Sentry or ACM panel.

Ensure that the door surface is clean and free from any debris. (Using neat alcohol to clean the surface is highly

recommended. Allow drying time before proceeding.)

Figure

Remove the protective cover from each tie-down pad and situate as shown in Figure .

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 6 of 10

Route the Cable between the lock and the Re ote Node / db Sentry Controller or ACM Panel –

Step 3

Route the lock cable to the door hinge as shown in Figure 3. Secure the cable to the tie-down pads using the

supplied cable-ties. Connect the supplied device cable to the RJ-45 coupler and route it to the Remote Node or

Sentry, if using Digitus a controller. If connecting to a third party access control panel, connect a network cable to RJ-

45 coupler and run back to panel.

Figure 3

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 7 of 10

Connect the cable to the Re ote Node / db Sentry Controller – Step 4

Locks are connected to the Remote Node or db Sentry’s socket circled in the diagram below.

Each Remote Node / db Sentry Controller has two device inputs, Dev 1 and Dev .

Side View of Remote Node

Side View of db Sentry

It is recommended that for a cabinet with doors, the front door is connected to Dev 1 and the back door is connected to

Dev .

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 8 of 10

Connect the lock to 3

-party Access Panel

Orange/White – GND, Ground

Orange – LOCK CTRL. Requires a 1 V ( 4V if a 4V version of the db CodeLock was purchased) control line to unlock the

handle

Green/White – RED LED. Connect to the Red LED output on the 3

-party panel

Blue – V+, Requires a 1 VDC Supply

Blue/White – LATCH POS (used to indicate if the lock is open or closed) – Will be pulled to Ground (GND) if the handle is

closed. Will be open circuit if the handle is open. See diagram below

Green – GREEN LED. Connect to the Green LED output on the 3

-party panel

Brown/White – Wiegand DATA 1

Brown – Wiegand DATA 0

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 9 of 10

Connect the SENSE OUT to onitor the lock position (open/closed)

If the 3

-party Access Panel requires a -wire input to monitor the door positions, an external relay is required.

Connect as follows:

Black

Wire

3rd-party Access Panel

NO NC

+V0V

External

Relay

+V 0V

SENSE OUT. Connect to

Blue/White Wire from ock.

DOOR

SWITCH

INPUT

Yellow

Wire

Blue

Wire

Red

Wire

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017

Page 10 of 10

Digitus Biometrics, Inc.

2 East Bryan Street, Suite 502

Savannah, A 31401 USA

Phone: 912-231-8175

Fax: 912.629.9478

www.digitus-biometrics.com

[email protected]

Specifications subject to change without notice.

Table des matières

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur