Digitrax DN126M2 Manuel utilisateur

Features:

▪FX3Function outputs for prototypical lighting eects and on/o control:

Constant Brightness Lighting with directional or independent control.

Optimized selectable LED or incandescent lamp operation

Realistic Eects like Ditch lights, Mars lights, strobes, and many more

Congurable Pulse Function available on all function outputs.

FX3 & Standard Function Qualiers operate functions based on direc-

tion, F0 on or o, direction and F0, and whether loco is moving.

Function Mapping for custom function setup.

Master Light Switch turns o all lights & functions with one keystroke.

Advanced Consist Function Controls.

▪Digitrax LocoMotion®System-Your locomotives look like the real thing.

The Digitrax LocoMotion System makes them run like the real thing too!

Scaleable Speed Stabilization (Back EMF) with simple setup & 256

level resolution.

Torque Compensation.

128 Speed Step operation (14 or 28 steps can also be used).

Momentum with acceleration and deceleration.

Normal Direction of Travel is user selectable.

Switching Speed feature for easier and faster access to yard speeds.

3 Step Speed Tables set start, mid and max voltage for custom control.

28 Step Speed Tables with 256 level resolution for precise control.

▪Program CVs using any Digitrax Compatible Control system without having

to buy any extra equipment.

▪2 Digit and 4 Digit Addressing.

▪Basic, Advanced & UniVersal Consisting.

▪SuperSonic motor drive for silent operation.

▪DIRect mode programming.

▪Decoder Reset CV with or without speed table reset.

▪Transponder Equipped ready for transponding on your Layout.

▪Motor Isolation Protection helps prevent damage to your decoder.

▪Automatic Analog Mode Conversion when running on DC layout.

▪Decoder Lock for individual programming of multiple decoders in one loco.

▪Digitrax “No Worries” Warranty.

DN126M2

Fits Micro Trains Line SW1500

Locomotive

.418” x .621” x .107”

10.63mm x 15.79mm x 2.72 mm

N Scale

Mobile Decoder

DCC Board Replacement

1.5 Amp/2 Amp Peak

2 FX3 Functions, 0.5 Amp

Complete Train Control

Run Your Trains, Not Your Track!

Parts List

1 DN126M2 Function Decoder

1 Instruction Sheet

Installation Information

See the Digitrax Decoder Manual V2 for complete decoder test procedures, instal-

lation instructions, programming and technical information. Digitrax manuals

and instructions are updated periodically. Please visit www.digitrax.com for the

latest versions, technical updates and additional locomotive-specic installation

instructions. CAUTION: Programming and layout track must not exceed

16V when using this decoder.

Installation Instructions

1. Carefully remove the fuel tank cover

and the locomotive’s shell from the

frame. Be extra careful to not

damage the pickups attached

to the locomotive shell, not

spreading the shell sides ade-

quately with e.g. toothpicks may

lead to the contacts catching

and being damaged as the shell

is being removed from the chas-

sis. (Figure 1) Notice the orientation

of the shell to the frame (Figure 2)

so that you can reinstall the shell

correctly.

2. Gently remove the wires from the

factory light board by pulling them

up and out of the sockets. (Figure 3)

3. Slide the factory light board forward

and out of the locomotive frame.

4. Install the DN126M2 by sliding it

back into the slot where the factory

light board was removed. Insert the

wires into the corresponding sockets

on the DN126M2. (Figure 4)

5. Replace shell and fuel tank cover.

Be extra careful to not damage the

pickups attached to the locomotive

shell. You are now ready to run your

locomotive. The DN126M2 is factory

programmed to address 03. You can

easily customize the address and

other features. See section “Customizing Your Decoder” that follows.

Figure 1. Removal of shell

Figure 2. Shell removed

Figure 3. Remove Factory Light Board

Factory Light board

Gently remove wires

Toothpicks

Shell Pickups

Customizing Your Decoder

Your Digitrax decoder is ready to run

and will operate using address 03 with

no additional programming. For a more

prototypical railroading experience,

your decoder can be customized for your

specic locomotive by programming

some of the Conguration Variables, or

CVs, available. See the Digitrax Decoder

Manual or the Digitrax web site for more

information.

Changing the Decoder Address

The rst CV most people change is the decoder address. This allows you to inde-

pendently control each loco with a unique address. Digitrax decoders are shipped

with CV01 (AD2), the two digit address, set to 03. Following is a brief description

of how to change the decoder address with a Digitrax DT4XX series throttle. See

your Starter Set Manual for complete programming instructions.

1. Go into DIRect Mode Programming on your system On the DT4XX

throttle press PROG until DIR is displayed.

2. Choose AD2 for 2 digit addressing or AD4 for 4 digit addressing.

3. Choose the address you want to set up for the decoder.

4. Complete address programming by pressing ENTER.

Note: CV29 must also be programmed to enable 4 digit addressing, this is done

automatically by the DT4XX throttles. See your Digitrax Decoder Manual or the

Digitrax Toolbox App for how to set up CV29.

Digitrax LocoMotion®System

Your locomotives look like the real thing, now you can make them run like the

real thing, too. Digitrax decoders incorporate torque

compensation for smooth as silk operation. You can also program CVs that

control momentum, 3 step and 128 step speed tables, switching speed, normal

direction of travel, scalable speed stabilization and more to take full advantage of

the Digitrax LocoMotion System.

Figure 4. Decoder Installed

Decoder Installed

Wires inserted in decoder

Momentum-CV03 & CV04

Momentum is part of the LocoMotion System. Acceleration is controlled by CV03

and deceleration by CV04. Both come from the factory set to 000. A range of 000

to 031 is available for both accel and decel. Try CV03:003 and CV04:000 as a

starting point for experimenting with momentum.

Speed Tables-How the Loco Responds to the Throttle

With Digitrax LocoMotion, there are two types of speed tables: 3 Step Tables

and High Resolution 28 Step Tables. Please see your Decoder Manual V2 for a

discussion of the 28 Step Tables. The 3 Step Tables are set up by programming 3

CVs: Start Voltage (CV02), Mid point Voltage (CV06) and Max Voltage (CV05).

These values are set at 000 at the factory. All have a range of values from 000 to

255. We recommend the following CV values as a starting point for experiment-

ing with speed tables.

Loco Type V Start

CV02

V Mid

CV06

V Max

CV05

Switcher

Concentrated low speed. Limited top

speed

002 038 064

Road Switcher

Prototypical top speed w/evenly

distributed curve from 0 to top speed

002 048 098

Mainline Loco

Quick increase to cruising speed then

levels o to prototypical top speed.

002 128 154

Other LocoMotion®Features: Switching Speed, Normal

Direction of Travel & Scalable Speed Stabilization

(Back EMF) Features

Switching speed is controlled by CV54. The factory setting is 000 for OFF. To

turn on the switching speed feature, program CV54 to a value of 001. When this

feature is on, use F6 to activate and deactivate switching speed. With the feature

on the throttle’s target speed is eectively reduced by about 50% and the eects

of accel and decel programmed into the decoder are reduced by 1/4. This is useful

for yard switching operations.

Normal Direction of Travel is controlled by CV29. See your decoder manual

or the Digitrax Toolbox App for additional information on the settings for CV29.

The intensity, or droop, of Scaleable Speed Stabilization (Back EMF) is

controlled by CV57. The factory setting for this feature is 006 which is suitable for

most locos. You can adjust this value in the range of 000 for OFF to 015 for the

maximum eect. Consult your Digitrax Decoder Manual for info about CVs 55 &

56 and their eects on scaleable speed stabilization.

SuperSonic Silent Operation and Torque Compensation

The factory settings in the decoder provide silent, smooth operation of your loco-

motive under most conditions. For more information about these settings, please

see the Digitrax Decoder Manual or our website.

Digitrax Transponding CV61

Digitrax Transponding is controlled by CV61. The initial factory set value is 000

for OFF. To turn on transponding, program CV61 to a value of 002. This al-

lows you to use Digitrax transponding to keep track of your rolling stock. When

transponding is enabled, the front light of the locomotive will icker slightly to

indicate transponding signal is being communicated.

Decoder Reset CV08

Decoder reset lets you reset all CV values to the initial factory settings. To reset all

CV values, program CV08 to a value of 008. You also have the option of reset-

ting all the CV values except the 28 speed step tables and CV60 selected sound

scheme. To do this program CV08 to a value of 009.

Warranty & Repair

Digitrax gives a one year “No Worries” Warranty against manufacturing defects

and accidental customer damage on all Digitrax command stations, boosters,

throttles, decoders, power supplies and layout control devices.

That’s it! A simple, straightforward warranty with no tricky language!

Visit www.digitrax.com for complete warranty details and instructions for

returning items for repair.

Please return warranty items directly to Digitrax - DO NOT return items

to place of purchase.

is page le intentionally blank.

Available

Computer Interface

Decoder Programmer

Sound Programmer

MPIRE

UILDER

Super

0 0 0 0

2443 Transmitter Road

Panama City, FL 32404

www.digitrax.com

Contact: www.digitrax.com/contact

Support: [email protected]

Repair: [email protected]

DN126M2

Fits Micro Trains Line SW1500 Locomotive

Made in the USA

Part 15, Class B

RFI Compliant

Table des matières

Autres manuels Digitrax Convertisseur de média

Digitrax

Digitrax SoundFX SDN144A1 Manuel utilisateur

Digitrax

Digitrax DH165K1A Manuel utilisateur

Digitrax

Digitrax DN163I0 Manuel utilisateur

Digitrax

Digitrax DN163I2 Manuel utilisateur

Digitrax

Digitrax DN163A2 Manuel utilisateur

Digitrax

Digitrax DN163A3 Manuel utilisateur

Digitrax

Digitrax SDH104K1A Manuel utilisateur

Digitrax

Digitrax SoundFX SFX004 Manuel utilisateur

Digitrax

Digitrax 3 Series Manuel utilisateur

Digitrax

Digitrax DN163K1a Manuel utilisateur

Digitrax

Digitrax DH166MT Manuel utilisateur

Digitrax

Digitrax DZ125 Manuel utilisateur

Digitrax

Digitrax DS44 Manuel utilisateur

Digitrax

Digitrax DZ126Z1 Manuel utilisateur

Digitrax

Digitrax SE74 Manuel utilisateur

Digitrax

Digitrax SoundFX SFX064D Manuel utilisateur

Digitrax

Digitrax DZ123MK1 Manuel utilisateur

Digitrax

Digitrax SE8C Manuel utilisateur

Digitrax

Digitrax SoundFX SDN144A0 Manuel utilisateur

Digitrax

Digitrax DN163I1C Manuel utilisateur

Digitrax

Digitrax DN166I1D Manuel utilisateur

Digitrax

Digitrax DH163A0 Manuel utilisateur

Digitrax

Digitrax DZ143 Manuel utilisateur

Digitrax

Digitrax DN163A1 Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur