Digital Watchdog DW-ESTS Manuel utilisateur
4. Right-click on ‘Ethernet’ and select ‘Properties’ from the drop-down options.
5. Double-click on ‘Internet Protocol version 4 (TCP/IPv4)’ in the Properties window.
6. Enter the IP and subnet mask as shown below and click the OK button.
7. Click the OK button in the Ethernet Properties window to close the window.
Quick Start Guide
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/support-download/
2. Search for your product by entering the part number in the “Search by Product”
search bar. Results for applicable part numbers will populate automatically based
on the part number you enter.
3. Click “Search”. All supporting materials, including manuals, Quick Start Guides
(QSG), software and firmware will appear in the results.
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours: 9:00 AM – 8:00 PM EST, Monday through Friday
digital-watchdog.com
Attention: This document is intended to serve as a quick reference for the initial setup. It is recommended
that the user read the entire instruction manual for complete and proper installation and usage.
DW-ESTS Complete Kit
DW-ESTCAM Camera Only
DW-ESTBLKB Blackbody Only
Quick Start Guide
Follow the diagram below to connect the
camera to all applicable external devices.
1. Install the Elevated Skin Temperature System software, available on Digital Watchdog’s website.
a. Go to http://www.digital-watchdog.com
b. Search for ‘EST software’ on the search bar at the top of the page.
c. The latest software will appear in the search results. Click on the link to download the file to
your computer and run the installation file.
2. When the camera connects directly to the PC, the following is assigned to the camera by default:
• Camera IP address: 169.254.100.100.
• Subnet mask: 255.255.0.0.
3. Open the execution window on the monitoring PC by pressing the “Window ( )+R” buttons.
Enter ‘ncpa.cpl’ and press ‘enter’.
STEP 1 – CAMERA CONNECTION
STEP 2 – SOFTWARE INSTALLATION
NOTE: The software is available for Windows® 10 OS only.
WHAT’S IN THE BOX
DW-ESTS Camera, Blackbody, LED strobe, 2x tripods, 2x power supplies, LAN cable, quick setup guide.
DW-ESTCAM Camera, LED strobe, power supply, quick setup guide
DW-ESTBLKB Blackbody, power supply, quick setup guide
NOTE: Make sure the PC’s IP address is not overlapping with the camera’s IP address. The PC’s
IP setting ranges arbitrarily from 169.254.100.1 ~ 169.254.100.254. Make sure to set the
subnet mask to 255.255.0.0.
NOTE: Install the Blackbody facing the camera, 9.8~14.7ft
from the camera (10ft is recommended) and
connect it to an adequate power supply.
Quick Start Guide
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
STEP 3 – SETTING UP YOUR SCREENING STATION
Rev: 10/20
NOTE: This product is not designed by DW for the specific intention of human fever detection nor the
diagnosis, mitigation, or prevention of disease or health conditions.
1. Install the camera facing away from the entrance or windows.
2. Place the camera 6.5~16.4ft from the monitoring path (10ft is recommended).
3. Place the camera at a 20° angle from the monitoring path.
4. Make sure people are walking into the camera’s FoV rather than straight towards the camera.
5. Place the Blackbody across from the camera, positioned in the corner of the camera’s FoV.
6. The Blackbody should be 9.8~14.7ft from the camera (10ft is recommended). 5ft is the
recommended height.
7. Setup a monitoring station next to the camera with a monitoring PC and personnel. See STEP 1.
8. One person in the FoV at a time.
9. Recommended room temperature is 68° to 86°F (20° to 30°C), under 80% humidity.
NOTES AND CONSIDERATIONS:
1. Allow the camera and Blackbody up to 5 minutes from power-up to calibrate properly.
2. When installing a camera-only solution, allow up to 30 minutes to calibrate.
3. When powering up the E.S.T. monitoring software, keep the camera’s FoV clear of people and
moving objects for 10 seconds.
FALSEFALSE
4. Do not install the camera or Blackbody under an air conditioner duct.
5. Strong fluorescent lights may impact temperature readings.
6. Sunlight from windows and large glass doors in the camera’s FoV may cause false readings.
7. Consider that any extensive physical activity performed before screening may impact the
facial skin temperature captured by the camera.
8. IMPORTANT! Always follow elevated temperature readings with additional screening such
as a medical thermometer and wellness questionnaire.
Ce manuel convient aux modèles suivants
2
Autres manuels Digital Watchdog Caméra thermique
