Digital Equipment PrintServer 32Printer Manuel
PrintServer32Printer
OptionalLargeCapacityInputTray
Operator’sGuide
Revision/Update Information: This is a new manual.
Order Number: EK–PSLCO–OC. A01
Digital Equipment Corporation
Maynard, Massachusetts
First Printing, March 1994
Digital Equipment Corporation makes no representations that the use of its products in the
manner described in this publication will not infringe on existing or future patent rights, nor do
the descriptions contained in this publication imply the granting of licenses to make, use, or sell
equipment or software in accordance with the description.
Possession, use, or copying of the software described in this publication is authorized only pursuant
to a valid written license from Digital or an authorized sublicensor.
© Digital Equipment Corporation 1994. All Rights Reserved.
Printed in U.S.A.
The postpaid Reader’s Comments forms at the end of this document request your critical evaluation
to assist in preparing future documentation.
The following are trademarks of Digital Equipment Corporation: PrintServer, VAX, VAX
DOCUMENT, and the DIGITAL logo.
All other trademarks and registered trademarks are the property of their respective holders.
S2425
FCC Notice
This equipment has been tested and found to comply with the limits of a Class A digital device,
Pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection
against harmful interference when the equipment is operated in a commercial environment. The
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
Canadian Department of Communications compliance statement:
This equipment does not exceed Class A limits per radio noise emissions for digital apparatus
set out in the Radio Interference Regulation of the Canadian Department of Communications.
Operation in a residential area may cause unacceptable interference to radio and TV reception
requiring the owner or operator to take whatever steps are necessary to correct the interference.
Avis de conformité aux normes du ministère de Communications du Canada:
Cet équipement ne dépasse pas les limites de Class A d’émission de bruits radioélectriques pour les
appareils numériques telles que perscrites par le Règlement sur le brouillage radioélectrique établies
par le ministère des Communications du Canada. L’exploitation faite en milieu résidential peut
entraîner le brouillage des réceptions radio et télé, ce qui obligerait le propriétaire ou l’opérateur a
prendre les dispositions nécessaires pour en éliminer les causes.
This document was prepared using VAX DOCUMENT Version 2.1.
Contents
1 Using the Optional Large Capacity Input Tray
1.1 SupportedPaperSizes........................................ 1–1
1.2 AddingPaper............................................... 1–3
1.3 ClearingPaperJams ......................................... 1–8
1.4 Troubleshooting ............................................. 1–11
1.5 ServiceNotes............................................... 1–12
Figures
1–1 PartsoftheOLCIT ....................................... 1–2
Tables
1–1 Conventions............................................. 1–1
1–2 OLCITLEDs ............................................ 1–11
1–3 PrintErrors............................................. 1–11
1–4 OLCITDiagnostics........................................ 1–12
iii
1
Using the Optional Large Capacity Input Tray
This book describes the following operator functions for the PrintServer 32
Printer Optional Large Capacity Input Tray (OLCIT).
• Adding paper (capacity 3000 sheets of 20 lb paper)
• Clearing paper jams
• Troubleshooting
Refer to the PrintServer 32 Printer Operator’s Guide for information on using the
PrintServer 32 printer.
Conventions
The following conventions are used in this manual:
Table 1–1 Conventions
Note A note provides important additional information.
Key A key name is shown enclosed in a box to indicate that you press
that key on the control panel. Key names are always shown in initial
capital letters.
1.1 Supported Paper Sizes
The Optional Large Capacity Input Tray (OLCIT) is designed to accept the
following paper sizes printed in either landscape (long edge feed) or portrait
(short edge feed) mode:
• Letter (LT) (8.5 inch x 11 inch)
• Letter (LTR) (11 inch x 8.5 inch)
• A4 (297 mm x 210 mm)
• A4R (210 mm x 297 mm)
Use recommended paper only, as listed in the PrintServer 32 Printer Operator’s
Guide.
Using the Optional Large Capacity Input Tray 1–1
Using the Optional Large Capacity Input Tray
1.1 Supported Paper Sizes
Parts of the OLCIT
The following illustration and table describe the parts of the OLCIT.
Figure 1–1 Parts of the OLCIT
DSG-000495
LT A4RA4 LTR
Paper
Mis-set
LT
A4R
A4
LTR
LT
A4R
A4
LTR
132
ADJUST AT 3 PLACES
Cover
Open
1
2
3
4
Number Description
Paper Tray Down button
Paper Size selection knob
Paper adjustment levers
Door
1–2 Using the Optional Large Capacity Input Tray
Using the Optional Large Capacity Input Tray
1.2 Adding Paper
1.2 Adding Paper
This section explains how to add paper to the OLCIT.
Note
When adding paper, make sure the PrintServer is not in the process of
printing and the operator panel reads Ready.
1. Press Pause on the PrintServer 32 operator panel.
Using the Optional Large Capacity Input Tray 1–3
Using the Optional Large Capacity Input Tray
1.2 Adding Paper
2. Press the Tray Down button
on the OLCIT.
Be sure the paper tray has stopped before continuing with the procedure.
DSG-000496
LT A4RA4 LTR
Paper
Mis-set
LT
A4R
A4
LTR
LT
A4R
A4
LTR
132
ADJUST AT 3 PLACES
Cover
Open
1
Note
If the tray runs out of paper while printing, the tray automatically lowers.
The elevator tray hesitates momentarily about half way up or down in its
travels and the Cover Open LED goes on momentarily. This is normal
operational behavior of the elevator tray and the Cover Open LED.
1–4 Using the Optional Large Capacity Input Tray
Using the Optional Large Capacity Input Tray
1.2 Adding Paper
3. Open the OLCIT door
.
Remove the two smaller paper trays above the OLCIT. This makes for
easy loading of paper and reduces the likelihood of paper jams.
DSG-000500
4
4. Fan about half a ream of paper at a time to release any static electricity.
Tap the paper on a hard surface to align the edges.
Insert the paper until the leading edge touches the back of the tray.
Make sure the edges or corners of the paper are not folded during
loading.
DSG-000498
Using the Optional Large Capacity Input Tray 1–5
Using the Optional Large Capacity Input Tray
1.2 Adding Paper
Note
Sloppy paper loading or folded/damaged paper edges and corners can
cause printer paper jams.
• Use recommended paper only, as listed in the PrintServer 32 Printer
Operator’s Guide.
• Do not add more than six reams of paper to the paper tray. Adding more
paper or loading the paper unevenly puts stress on the paper tray motor
and causes paper jams.
5. Close the OLCIT door
.
DSG-000497
4
1–6 Using the Optional Large Capacity Input Tray
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Digital Equipment Accessoires pour imprimantes
