Digital-Ally DTM-600 Manuel utilisateur
860-00323-00 Rev E pg.1
DTM-600
Installation Guide
860-00323-00 Rev E pg.2
Contents
1.Overview…………………………. ...............................................................................................................................................3
2. Wiring Diagram .................................................................................................................................................................4
3. Floor Stand Option............................................................................................................................................................6
3.1. Floor Stand…………………..................................................................................................................................................7
3.2. Temp Sensor Option……...............................................................................................................................................11
3.3. Forehead Temperature Sensor Option........................................................................................................................18
4. Desktop Stand Option…….. .............................................................................................................................................24
5. Wall Mount Option………… ..............................................................................................................................................25
6. Terminal Configuration….. ..............................................................................................................................................27
6.1. Device Startup and Login.....................................................................................................................................27
6.2. OSD Configuration………………………………………………………………………………………………………………………………………….28
6.3. Web Portal Configuration....................................................................................................................................30
7.Contact Information……………...........................................................................................................................................33
860-00323-00 Rev E pg.3
1. Overview
This document provides assembly instructions for the Floor Stand, Desk Stand, Wall Mount, and
Temperature Sensor options for the DTM-600.
The wiring diagram for the terminal and temp sensor apply to each of the three mounting options.
Floor Stand
Option
Desktop
Stand
Option
Wall
Mount
Option
Temp Sensor
Wall Mount
Option
Forehead
Sensor
Option
860-00323-00 Rev E pg.4
2. Wiring Diagram
Power and Temp Sensor
Wiring Kit
•Crimp Connectors
•Barrier Block
•Power Harness
•Wiring Guide
AC/DC Adapter
Power
Harness
+12vdc
AC Cable
RS485 P
Orange
RS485 N
Purple
RS485 N
Brown
RS485 P
Blue
+12vdc
Gnd
Ethernet
Network
Jack
AC
Outlet
Crimp Connector
Solution
Terminal
Red OR
Black with stripe
Wrist Temp Sensor
OR
Forehead Temp Sensor
Note:
The DTM-600 firmware
can differentiate between
the Wrist Temp Sensor
and Forehead Temp
Sensor. No additional
configuration is required.
860-00323-00 Rev E pg.5
Power
Harness
RS485 P
Orange
RS485 N
Brown
RS485 P
Blue
+12vdc
Gnd
Barrier Block
Solution
RS485 N
Purple
Ethernet
Terminal
Wrist Temp Sensor
OR
Forehead Temp Sensor
Network
Jack
+12vdc
AC Cable
AC
Outlet
AC/DC Adapter
Red OR
Black with stripe
Note:
The DTM-600 firmware
can differentiate between
the Wrist Temp Sensor
and Forehead Temp
Sensor. No additional
configuration is required.
860-00323-00 Rev E pg.6
Ground
3. Floor Stand Option
The mounting plate packaged with the DTM-600 terminal and the mounting bracket packaged with the Temperature
Sensor is mounted to the floor stand. Once the hardware is assembled, reference the wiring diagram to complete the
assembly.
The Floor Stand Base is an option to raise the Floor Stand.
The Extension Plate packaged with the Floor Stand is an option to raise the mounting height of the Terminal.
Floor Stand
Temp Sensor
Bracket Options
Temp Sensor
Mounting
Terminal
Mounting
Floor Stand
Covers
Final Assembly
Floor Stand
Base Option
Extension Plate
Option
Extension Plate Cover
placed over plate
860-00323-00 Rev E pg.7
3.1. Floor Stand
Remove the floor stand from the packaging.
For ease of assembly, place the floor stand on the floor or table face down.
Remove the terminal back plate by removing the 2 screws.
Remove the adapter back plate from the floor stand by removing the 2 screws.
terminal
back plate
adapter
back plate
base
back plate
860-00323-00 Rev E pg.8
Remove the AC adapter plate from the mid-way back plate by removing the 2 screws.
Note: bending the AC adapter plate as shown will allow the AC adapter to seat flush.
Seat the AC adapter on the adapter plate.
Seat the AC adapter plate atop the mid-way back plate and secure in place with 2 screws.
860-00323-00 Rev E pg.9
Plug the AC cable into the AC adapter.
Remove the back plate at the base of the floor stand.
Feed a network cable (not supplied) into the mid-way access cutout to the top and bottom of the floor stand.
Orient the AC adapter cables as shown below and carefully reseat the mid-way back plate.
860-00323-00 Rev E pg.10
Secure the mid-way back plate in place with 6 screws.
Orient the base plate to align the threaded studs to the floor stand.
Seat and thread the nuts to the threaded studs.
Orient the base back plate to allow the network cable and AC cable through the plate.
Secure the base back plate in place with 4 screws.
Set the floor stand on the side as shown with the temp sensor mounting holes facing up.
Autres manuels pour DTM-600
1
Table des matières
