DIGISYSTEM VM-2000 Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Autres manuels DIGISYSTEM Équipement de laboratoire

DIGISYSTEM

DIGISYSTEM PS-600T Manuel utilisateur

DIGISYSTEM

DIGISYSTEM DSD-100 Manuel utilisateur

DIGISYSTEM

DIGISYSTEM DSC-302SMD Manuel utilisateur

DIGISYSTEM

DIGISYSTEM RM-501 Manuel utilisateur

DIGISYSTEM

DIGISYSTEM DSC-103SD Manuel utilisateur

DIGISYSTEM

DIGISYSTEM DSB-500 Manuel utilisateur

DIGISYSTEM

DIGISYSTEM DSD-100D Manuel utilisateur

DIGISYSTEM

DIGISYSTEM DSO-D Series Manuel utilisateur

DIGISYSTEM

DIGISYSTEM WB-500D Manuel utilisateur

DIGISYSTEM

DIGISYSTEM DSB-500D Manuel utilisateur

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur

DIGISYSTEM LABORATORY INSTRUMENTS INC. www.digisystemlab.com REV.2-2020

INSTRUCTION MANUAL FOR VORTEX MIXER VM-2000 & VM-2000-C

VM-2000-C VM-2000

Warnings:

* Do not remove the mixer during operation.

* Place the mixer securely away from the edge of bench to avoid the mixer falling off the bench top.

* Do not disassemble the mixer by yourself. In the event of a malfunction, the mixer should be repaired by a

qualified technician. Before repairing, turn off the power.

* Clean up the head once the user finds any liquid on the head, otherwise the head will get damaged easily.

Steps:

1. Place the mixer on a flat and stable bench top. Plug the mixer into a properly grounded outlet which

corresponds with the electrical requirements on the label back on machine.

2. Place the ‘Switch’at ‘TOUCH’position. The unit will run as soon as touch on the ‘Head’. The ‘Power

indicator’lights.

3. Place the ‘Switch’at the ‘AUTO’position, the unit will run automatically.

4. Turn the ‘Speed controller’to the required speed.

Warning: Do not make the motor race rotation to avoid damage. After finishing operation, please place the

switch at ‘TOUCH’or ‘OFF’position.

Maintenance and care:

Keep the machine clean all the time, so no routine maintenance is required. Cleaning can be done with a

damp cloth. Avoid the use of solvents as they may damage the machine housing.

Circuit Diagram

Head

Speed controller

Switch

(AUTO/OFF/TOUCH)

DIGISYSTEM LABORATORY INSTRUMENTS INC. www.digisystemlab.com REV.2-2020

Service Manual

Troubleshooting Guide

Caution: Always disconnect the power cord before troubleshooting.

Trouble

Cause

Remedy

Instrument inoperative

Power cord not connected to outlet.

Plug in the power cord.

Dead power output.

Change to different output.

Defective electronic component.

Contact your distributor for repair.

Head doesn’t rotate

Switch isn’t at ‘AUTO or “TOUCH’ position.

Place the switch at ‘AUTO or “TOUCH’ position.

Eccentric brass rod doesn’t work well.

Contact your distributor for repair.

Switch is broken.

Contact your distributor for repair.

Motor is broken.

Contact your distributor for repair.

PC board is broken.

Contact your distributor for repair.

Speed can’t not be controlled

PC board is broken.

Contact your distributor for repair.

Speed controller is broken.

Contact your distributor for repair.

There is a big noise during

operation

Eccentric brass rod doesn’t work well.

Contact your distributor for repair.

Belt which is to fix the eccentric brass rod

doesn’t work well.

Contact your distributor for repair.

The “TOUCH” function can’t

work

Switch isn’t at “TOUCH’ position.

Place the Switch at ‘TOUCH’position.

The starting button under the motor is broken.

Contact your distributor for repair.