Digimerge DND7220 Series Manuel utilisateur
HIGH RESOLUTION DUAL-CODEC
VANDAL RESISTANT DAY/NIGHT
DOME NETWORK CAMERA
DND7220
Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
series
Page 2
www.digimerge.com
DND7220 Series_Quick Installation Guide_En_R1
This installation guide provides instructions for installing the Digimerge
DND7220V High Resolution Dual-Codec Vandal Resistant Day/Night Dome
Network Camera on your network. For all other aspects of using the product,
please refer to the user manual available at www.digimerge.com or on the
Installation CD included with this product.
• 1 x High Resolution Dual-Codec Vandal Resistant Day/Night Dome Network Camera
• 1 x 12V DC Power Adaptor
• Mounting Hardware
• 2 x Allen Keys for Security Screws
• 1 x Quick Installation Guide
• 1 x Installation CD with manuals and software
• 1 x Warranty Card
PACKAGE CONTENTS
IMPORTANT!
This product must be installed in compliance with local laws and regulations.
Package Contents:
Camera 12V DC Power Adaptor Mounting Hardware
Allen Keys for Security
Screws
Quick Start
Guide
Installation
CD
ETHERNET PORT / PWR / NET LED INDICATORS
ALARM BLOCK
BNC CONNECTOR (ANALOG VIDEO SIGNAL)
AUDIO CONNECTOR (MICROPHONE)
POWER INPUT CONNECTOR
CAMERA
DND7220 Series_Quick Installation Guide_En_R1
www.digimerge.com
Page 3
• Hardware installation:
A. Installing the Base
B. Adjusting the Lens
C. Connecting the Cables
• Software installation
• Network configuration
HARDWARE CONNECTIONS
1
2i
Hardware Installation - Installing the Base
NOTES:
• If you wish to change the Cable Location (Cable
Conduit), please refer to User Manual Appendix #2
prior to installation.
• Do not remove the Dome Cover Plastic Protector
until the end of the installation.
1. Remove the Cover from the Camera by removing
the 4 securing screws using the large silver
proprietary Hex Tool.
2. Attach the base to a Wall or Ceiling:
i. Hold the base up to the desired location. Use a
Pencil or Marker to mark the 4 hole locations.
ii. Use a drill with the correct bit type, and drill
holes on the marked positions. Hammer the
Screw Plugs (included with the Hardware Pack)
into the holes.
iii. Place the rubber washer onto the screw (both
provided with the Hardware Pack). Repeat for all
screws.
iv. Use a screwdriver to install the 4 screws through
the holes in the base into the mounting surface.
A
1
2ii 2iii 2iv
Page 4
www.digimerge.com
DND7220 Series_Quick Installation Guide_En_R1
HARDWARE CONNECTIONS
1
Continued
Hardware Installation - Adjusting the Lens
NOTE: The lens should be adjusted prior to
reattaching the camera cover. If you are adjust-
ing the Camera using a direct connection to a
PC, you will need to use a Crossover Ethernet
Cable, or use the BNC Analog Output.
1. Adjust the Angle, Zoom and Focus
controls:
i. Loosen the two screws on the side of the
Lens. Adjust the Angle of the Lens
assembly, and tighten the screws to hold
the assembly in the desired position.
ii. Use a screwdriver to loosen the Zoom screw.
Move the adjusting screw left and right to
turn the Zoom Ring. Once the lens is set to
the desired Zoom, tighten the screw to hold
the lens placement.
iii. Use a screwdriver to loosen the Focus
screw. Move the adjusting screw left and
right to turn the Focus Ring. Once the lens
is set to the desired Focus, tighten the
screw to hold the lens placement.
iv. Replace the Cover on the Camera Base
and attach with the 4 securing screws with
the Security Hex tool.
B
1i
ZOOM
RING
1ii
1iii
SCREW 1 SCREW 2
FOCUS
SCREW
DND7220 Series_Quick Installation Guide_En_R1
www.digimerge.com
Page 5
Hardware Installation - Connecting the Cable
The Camera has a single cable, which splits into
several different connection ports:
1. Ethernet: Connect an Ethernet Cable to the
RJ-45 Ethernet port to connect the Camera to
the network.
• The Red PWR LED indicates the Power state
of the Camera (ON/OFF).
• The Green NET LED indicates the Network
state of the Camera. The LED will blink when
network communication occurs.
2. BNC: Connect a BNC Cable to view the Camera
on a CCTV Monitor or DVR with analog
(non-IP)Video inputs. This is an optional
connection.
3. Audio: Connect an RCA Cable to the audio
port on a CCTV Monitor or DVR (when using a
BNC Video Connection) to listen to Audio from
the camera. This is an optional connection.
4. Alarm Block: The Camera Alarm Block can be
used to send or receive a signal from a
compatible DVR or CCTV System. Please
consult the manual for the device you wish to
connect to the camera for details.
i. Use a small screwdriver to loosen the selected
screws.
ii. Insert the cables for the Alarm, NO, COM or
GND (as needed)
iii. Use the screwdriver to tighten the screws to
hold the cables in place.
5. Power Adaptor: Connect one end of the Power
Adaptor to the camera once all other
connections have been made. Connect the
other end to a compatible power source.
HARDWARE CONNECTIONS
1
C
1
Continued
2
3
4
4i 4ii
Page 6
www.digimerge.com
DND7220 Series_Quick Installation Guide_En_R1
SOFTWARE INSTALLATION
2
The Digiconsole application loads
from the CD included with your
package, and provides you with the
following:
1. Web links to various resources
and documentation
2. Discovery of all the Digimerge
IP devices on the network
3. Provides Network
configuration of IP Devices
4. Installs DigiConsole and
Surveillance application on your
local PC
5. Warranty information and DDNS
registration
A
Digiconsole Utility screen consists of
the following menus:
1. Home
2. Find Devices
3. Register
4. Install
B
DND7220 Series_Quick Installation Guide_En_R1
www.digimerge.com
Page 7
Home:
Provides basic Digiconsole operating
instructions, links to product informa-
tion/documentation as well as 3rd party
software support links.
SOFTWARE SET-UP
A
Find Devices:
Locates all available Digimerge IP
devices on your network and displays
a snapshot of the results. Click on any
available device to display image on
the right side screen display.
NOTE: You may need to press the Find
Devices button several times as some
devices may not respond immediately.
If you do not see a camera image,
please check that all cables running
from the Camera are connected
properly.
B
C
Menu:
The Menu Button or right clicking on
a device icon provides access to
device specific settings:
• Edit Network Parameters
• View Live Image
• Open Device in Browser
• Update Firmware in Video Device
• Refresh the device list - in order to
remove inactive and disconnected
devices
NOTE: It is recommended that you
record the device specific MAC and
IP address for DDNS registration
purposes. If you have multiple
cameras on a local network, only
one camera needs to be configured
for DDNS.
3
MAC:
IP:
Page 8
www.digimerge.com
DND7220 Series_Quick Installation Guide_En_R1
SOFTWARE SET-UP
Edit Network Parameters:
The Network Parameters are
automatically assigned to the
Device by the network router (by
using DHCP). These settings can
be manually changed if desired.
1. Select the IP device you would
like to edit by clicking on its icon.
2. Click on the MENU button or
right click the icon for the device
to access the menu. Select
“Edit Network Parameters” from
the menu.
3. Make the necessary changes
and click OK to save changes or
click CANCEL to close the
window without saving any of the
changes made.
NOTE: If a user name and password
were set-up on the IP Device previ-
ously, you will be required to enter
this authentication information when
attempting to access the device.
C1
Continued
View Live Image:
View live video from the IP Device
using the Apple Quicktime program.
If this application is not installed on
your system, please download it (no
charge) at
http://www.apple.com/quicktime
C2
3
OPTIONAL
If by clicking VIEWING LIVE IMAGE
the image is not automatically shown
in Quicktime, follow these steps in
Quicktime:
1. Go to FILE
2. Choose OPEN URL
3. Enter the following: rtsp://<device
IP address> (i.e. rtsp://192.168.2.102)
A device IP address can be obtained
from the Digiconsole device list.
NOTE: Minimum Quicktime version installed
should be 7.1.6. If you cannot install Quick-
time, use Microsoft Internet Explorer to view
the device. See step C3 for details.
DND7220 Series_Quick Installation Guide_En_R1
www.digimerge.com
Page 9
SOFTWARE SET-UP
Continued
Open Device in Browser:
Opens up the DigiViewer Video Browser
using your default web browser (e.g.
Internet Explorer).
The DigiViewer browser allows the user
to view streaming video from the device
as well as change certain settings on the
device depending on the level of access
set by the administrator.
C3
3
Once user names and passwords are set
up by the administrator, the users (except
for a VIEWER level user) are required to
enter this information every time they ac-
cess the DigiViewer.
Click (during streaming mode)
to mute the audio.
Click to capture a snapshot image
in a new browser window.
By default, the image refresh rate
is set to OFF. Move slider to the
right to set image refresh rate.
Click to bring up image brightness and contrast controls
Click to capture a video clip and send it to a FTP site. FTP
must be configured in the SETTINGS screen
Click here to start streaming video
Page 10
www.digimerge.com
DND7220 Series_Quick Installation Guide_En_R1
SOFTWARE SET-UP
3 Levels of User Access:
• Administrator (current user)
• Operator (general user)
Default User Name: guest
Password:<leave blank>
• Viewer (anonymous guest)
Creating Current User Account:
1. Click SETTINGS
2. Select ACCOUNTS
3. Fill in a user name and
password in the assigned fields
4. Reconfirm password
5. Click UPDATE ACCOUNTS
1. Administrator: Administrator has
unrestricted access to all the
settings of the device. The
interface will only permit creation
of ONE administrator account.
2. Operator: Operator has restricted
access to the settings of the
server. The interface will only
permit creation of FIVE operator
accounts.
Note: Restrictions - View images.
Requires username and password.
3. Viewer: The interface will permit
the creation of ONE viewer
account (i.e. Anonymous Guest).
This account does not require a
password.
Note: Viewer Restrictions - View im-
ages if permission is granted by ad-
ministrator. Note that the permission
in this case refers to providing the
IP address to someone. Whomever
receives the IP address can view the
camera remotely as a anonymous
guest. No password is required.
Multiple users can access the de-
vice at the same time, however this
will limit the quality and speed of the
video as the feed is shared between
all connected users.
Continued
3
Autres manuels pour DND7220 Series
1
Table des matières
