Diamondback 64684 Instructions de montage
!"#"$%&'(%)*+#"$*%,$-%.$$/-00)))1.,(+&(2(*"3.$14&5
%65,"7%&'(%$*4.8"4,7%#'//&($%,$-%/(&9'4$#'//&($:.,(+&(2(*"3.$14&5
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 18i
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2018 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly an d se rv ic e may n ot b e in cl uded.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 64684
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
G,+7*%&2%O&8$*8$#
Safety ........................................................................2
Specifications ............................................................7
Setup .........................................................................8
Operation ..................................................................13
Maintenance .............................................................18
Parts List and Diagram .............................................21
Warranty ...................................................................24
QFKMLMR%EHNSITE%FMU%U6;LMLGLIME
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
LNJIKGFMG%EF;6GH%LM;IKNFGLIM
R*8*(,7%G&&7%E,2*$V%Q,(8"83#
K*,9%,77%#,2*$V%),(8"83#%,89%"8#$('4$"&8#1%%
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
E,W*%,77%),(8"83#%,89%"8#$('4$"&8#%2&(%2'$'(*%(*2*(*84*1
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning it on.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.
Page 3;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 64684
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
9. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
10. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
11. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than using your
hand and it frees both hands to operate tool.
12. DON’T OVERREACH.
Keep proper footing and balance at all times.
13. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.
14. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.
15. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.
16. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
17. NEVER STAND ON TOOL.
Serious injury could occur if the tool is tipped or
if the cutting tool is unintentionally contacted.
18. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
19. DIRECTION OF FEED.
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.
20. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
Page 4 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 64684
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
R(&'89"83%L8#$('4$"&8#
%
GI%JK6!6MG%6T6OGKLO%EXIOY%FMU%U6FGX%;KIN%LMOIKK6OG%
RKIPMULMR%QLK6%OIMM6OGLIM%K6FU%FMU%;ITTIQ%GX6E6%LMEGKPOGLIME-
>>Z?>[Z%!FO%R(&'89*9%G&&7#-%G&&7#%)"$.%G.(**%J(&83%J7'3#
1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.
6. Repair or replace damaged or
worn cord immediately.
R(&'89"83%
J"8
>[B%!FO%\?J(&83%J7'3%,89%I'$7*$
]2&(%'/%$&%>[B%!FO%,89%'/%$&%>B%F^
7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
>[B%!FO%\?J(&83%J7'3%,89%I'$7*$. The tool has
a grounding plug that looks like the plug illustrated
above in >[B%!FO%\?J(&83%J7'3%,89%I'$7*$.
8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.
9. Do not use an adapter to connect
this tool to a different outlet.
G"7*%E,)%E,2*$V%Q,(8"83#
;&(%H&'(%I)8%E,2*$V%K*,9%L8#$('4$"&8%
N,8',7%S*2&(*%I/*(,$"83%E,)
1. Wear eye protection.
2. Use saw-blade guard and spreader
for every operation for which it can be
used, including all through sawing.
3. Keep hands out of the line of saw blade.
4. Use an appropriate push-stick when required.
5. Know how to reduce risk of kickback.
6. Do not perform any operation freehand.
7. Never reach around or over saw blade.
8. Make sure the workpiece is supported
at all times while sawing.
9. To properly understand all safety warnings,
be familiar with the following safety
terms and equipment:
a. Featherboard – A block with “fingers” that hold
the workpiece against the fence while sawing.
b. Through-sawing – A cut made from one side of
a tile to the opposite side, without stopping.
c. Push-stick – A narrow strip of wood or other
soft material with a notch cut into one end
and which is used to push short pieces
of material through saws. It provides a
safe distance between the hands and the
cutting tool. Must be narrower than the cut
width to prevent contact with the blade.
d. Freehand – Feeding a workpiece through the
saw without using a fence or guided support
to guide it. MIG%F%EF;6%N6GXIU1
Page 5;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 64684
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
e. Kerf – The gap made by the
saw in the workpiece.
f. Kickback – A sudden reaction to a pinched,
bound, or misaligned blade, causing
an uncontrolled workpiece to lift up and
out of the saw toward the operator.
g. Spreader – A metal plate that follows the
saw blade to keep the kerf (gap) from
closing on the saw blade. Spreaders,
except riving knives, must be aligned to the
blade after blade adjustment to prevent binding.
10. As noted previously, Y"4_+,4_ is a sudden reaction
to a pinched, bound, or misaligned blade,
causing an uncontrolled workpiece to lift up and
out of the saw toward the operator.
Kickback is usually a result of tool
misuse and can be limited or avoided by
following the precautions below:
• Fence must be completely
parallel to the saw blade.
• Workpiece must be free from flaws
and from foreign objects.
11. Do not use a dull or damaged blade.
12. Maintain control of the workpiece. Do not
allow the workpiece to rest against the
moving blade without holding onto it.
• If the blade binds or a cut is interrupted, turn
off the power switch and hold the workpiece
still until the blade stops. Correct the cause
of blade binding before proceeding.
• Before continuing an unfinished cut,
center the blade in the pre-cut kerf and
check that the saw is not engaged into the
workpiece before turning on the saw.
• Push the tile past the blade prior to release.
13. Check guards for proper operation with saw
disconnected from power before each use.
Do not disable any guard. Do not operate
saw if any movable guard does not move
freely and close instantly. Make sure any
movable guard does not touch the blade in
all angles, depths of cut, and positions.
14. Keep the guard in place while through-sawing.
Verify that the spreader lines up with
the blade to prevent binding.
JIELGLIM%I;%GLT6%EFQ
J&)*(%O&(9
G"7*%E,)
U("/%
T&&/
U("/%T&&/
15. To avoid the possibility of the tool plug or
receptacle getting wet, position tile saw to one
side of a wall mounted receptacle to prevent
water from dripping onto the receptacle or plug.
The user should arrange a “drip loop” in the cord
connecting the saw to a receptacle. The “drip
loop” is that part of the cord below the level of
the receptacle, or the connector if an extension
cord is used, to prevent water traveling along the
cord and coming in contact with the receptacle.
16. If the plug or receptacle does get wet, DON’T unplug
the cord. Disconnect the fuse or circuit breaker
that supplies power to the tool. Then unplug and
examine for presence of water in the receptacle.
R;OL%JK6OFPGLIME
17. Test GFCI (Ground Fault Circuit Interrupter)
before each use as follows:
a. Plug GFCI into power outlet and press
reset button. Indicator should turn on.
b. Press test button. Indicator should turn off.
c. Press reset button again for use.
Do not use if above test fails.
The GFCI device does not protect against electrical
shock due to contact with both circuit conductors or
a fault in any wiring supplying the GFCI device.
G&%,77&)%R;OL%'8"$%$&%2'84$"&8%/(&/*(7V=%
6`G6MELIM%OIKUE%NPEG%MIG%
S6%PE6U%)"$.%$."#%GLT6%EFQ1
Page 6 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 64684
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
FUULGLIMFT%GLT6%EFQ%EF;6GH%QFKMLMRE%
18. UI%MIG%IJ6KFG6%QLGX%FMH%RPFKU%
ULEFST6U=%UFNFR6U=%IK%K6NI!6U1%%N&W"83%
3',(9#%5'#$%5&W*%2(**7V%,89%47&#*%"8#$,8$7V1
19. This product Is provided with A Ground Fault
Circuit Interrupter (GFCI) built into the power
cord plug. If replacement of the plug or cord is
needed, use only identical replacement parts.
20. WARNING – To reduce the risk of electrocution,
keep all connections dry and off the ground.
Do not touch plug with wet hands.
21. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.
22. When servicing use only identical replacement parts.
23. Do not depress the spindle lock when
starting or during operation.
24. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
25. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
26. Industrial applications must follow OSHA guidelines.
27. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
28. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
29. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
30. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
Page 7;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 64684
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
!"+(,$"&8%E,2*$V
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Use tools with the lowest vibration when there
is a choice between different processes.
4. Include vibration-free periods each day of work.
5. Grip workpiece as lightly as possible (while still
keeping safe control of it). Let the tool do the work.
6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
%EF!6%GX6E6%LMEGKPOGLIME1
E/*4"2"4,$"&8#
Electrical Rating 120VAC / 60 Hz / 15 A
Motor No Load Speed 4,000 RPM
Max. Blade Diameter 10"
Arbor Size 5/8"
O,'$"&8- Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
O,'$"&8- The use of optical instruments
with this product will increase eye hazard.
LASER LIGHT
DO NOT STARE INTO BEAM
Max. Output: 1 mW,
Wavelength: 650 nm
CLASS IIa LASER PRODUCT
This product complies with
21 CFR 1040.10 and 1040.11
Distributed by Harbor Freight Tools
3491 Mission Oaks Blvd.
Camarillo, CA 93011 63900
Manufacture Date: ___________, ______
AVOID EXPOSURE
Laser light is emitted
from this opening.
Page 8 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 64684
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
E*$'/%?%S*2&(*%P#*-
%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*a$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
;'84$"&8#
S*W*7%%
T&4_%T*W*(
Q,$*(%
G(,V
Q,$*(%
G(,V%
;(,5*
Q,$*(%
J'5/
N"$*(%
R,'3*
U(,"8%
J7'3
J'5/%
S,#"8
J'5/%
J&)*(%
O&(9
E$,89%
]#&79%#*/,(,$*7V^
Toggle Table
Stop
G,+7*
E/"897*%
T&4_
K*,(%
6a$*8#"&8%
G(,V
Reset
Button
J'5/%
I'$7*$
J&)*(%
E)"$4.%
J&)*(%
O&(9
U*/$.%
T&4_
U*/$.%
E$&/
U*/$.%
Y8&+
Table
Lock
Lever
6a$*8#"&8%G,+7*%
T&4_%Y8&+
6a$*8#"&8%
G,+7*
E"9*%
6a$*8#"&8%
G(,V%F%
S7,9*%R',(9%
T&4_%Y8&+
E"9*%
6a$*8#"&8%
G(,V%S
S7,9*
G,+7*%
E$&/
K*#*$%S'$$&8- Directly above the Power Switch is
the Reset Button. If the Tile Saw overheats it will shut
down automatically. Allow it to cool down, make sure
there are no loose connections or damaged cords,
and then press the Reset Button to restart the Saw.
Do not force workpieces into the saw and make sure
the blade is properly wetted to reduce overheating.
G&337*%G,+7*%E$&/- This allows the Table to be
removed if needed. Lift the Stop and turn it to
lock/unlock. If the slot is aligned with the Table,
the Table can be removed. If the slot is turned
sideways, the Table is locked into the saw.
G,+7*%T&4_%T*W*(- To lock the Table in place,
line up this Lever′s pin with the hole in the
rail, and press the Lever towards the rail. Pull
out on the Lever to unlock the Table.
Page 9;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 64684
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
FEE6NSTH
GI%JK6!6MG%E6KLIPE%LMbPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
G'(8%$.*%J&)*(%E)"$4.%&2%$.*%$&&7%&22%,89%'8/7'3%$.*%$&&7%2(&5%"$#%*7*4$("4,7%&'$7*$%
+*2&(*%/*(2&(5"83%,8V%/(&4*9'(*%"8%$."#%#*4$"&81
M&$*- For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
L8#$,77"83%N&$&(%X*,9
1. Place four Sleeves (4) into top mounting holes
on side of Water Tray Frame (5) as shown.
2. Align the holes in the Motor Head Assembly
with the corresponding mounting holes
on the side of the Water Tray Frame.
3. Insert four M10 x 50 Socket Head Cap Screws (1)
through four Flat Washers (2). Insert through
mounting holes on end of Water Tray Frame and into
Motor Head Assembly, as shown. Finger tighten.
4. Insert two M10 x 70 Socket Head Cap
Screws (153) through two Flat Washers,
and then into holes on side of Motor Head.
Secure using M10 Lock Nuts (7).
5. Place Clear Hose from Motor Head Assembly
into two Hose Clamps (6) on Frame. Squeeze
Clamps together to secure Hose.
6. Tighten previously installed M10 x 50
Socket Head Cap Screws securely.
Q,$*(%
G(,V%
;(,5*
E7**W*%
N&$&(%
X*,9%
F##*5+7V
M10 x 50
O,/%E4(*) N>Z%
T&4_%M'$
M10 x 70
O,/%E4(*)
X&#*%
O7,5/
X&#*
;7,$%
Q,#.*(
;7,$%Q,#.*(
N&$&(%X*,9%L8#$,77,$"&8
Page 10 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 64684
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
Q.**7%L8#$,77,$"&8
1. Align the holes in the Right Wheel Bracket (174)
with the corresponding mounting holes on the
side of the Water Tray Frame. Insert four M6 x 30
Socket Head Cap Screws (175) through the
Bracket into the Frame and tighten securely.
2. Slide one Ø12.5 Washer (172), Wheel (173), and
Ø10 Flat Washer (2) onto the axle on the Wheel
Bracket. Secure in place with an M10 Lock Nut (7).
3. Repeat procedure with the Left Wheel
Bracket (157) and second Wheel.
Q,$*(%
G(,V%
;(,5*
Q.**7%
K"3.$%Q.**7%
S(,4_*$
N>Z%
T&4_%M'$
M6 x 30
O,/%E4(*)
Ø>[1B%
Q,#.*(
Ø>Z%
Q,#.*(
Q.**7%L8#$,77,$"&8
L8#$,77"83%E/7,#.%R',(9#
1. Attach the Rear Splash Guard (110) to the back
of the Blade Guard with a Ø5 Flat Washer (108)
and M5 x 12 Pan Head Screw (40).
2. Align the hole on each end of the Side Splash
Guard (107) to the screw on each side of
the Blade Guard and press the holes on
the Splash Guard through the screws.
M&$*- It is not necessary to loosen or
remove the screws on the Blade Guard
to install the Side Splash Guard.
K*,(%
E/7,#.%
R',(9
E"9*%E/7,#.%
R',(9
S7,9*%
R',(9
S7,9*%
R',(9
M5 x 12 Screw
Ø
B%
Q,#.*(
X&7*
E4(*)
E/7,#.%R',(9%L8#$,77,$"&8
Table des matières
Autres manuels Diamondback Scie
