12. Remove adjusting keys or
wrenches before turning the tool
on. A wrench or a key that is left at-
tached to a rotating part of the tool
may result in personal injury.
13. Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enables
better control of the tool in unex-
pected situations.
14. Use safety equipment. Always
wear eye protection. Dust mask,
non-skid safety shoes, hard hat,
and hearing protection must be
used for appropriate conditions.
Ordinary eye or sun glasses are
NOT eye protection.
TOOL USE AND CARE
15. Use clamps or other practical
ways to secure and support the
workplace to a stable platform.
Holding the workpiece by hand or
against your body is unstable and
may lead to loss of control.
16. Do not force tool. Use the cor-
rect tool for your application. The
correct tool will do the job better
and safer at the rate for which it is
designed.
17. Do not use tool if switch does
not turn it on or o. Any tool that
cannot be controlled with the switch
is dangerous and must be repaired.
18. Disconnect the plug from the
power source before making any
adjustments, changing acces-
sories, or storing the tool. Such
preventative safety measures
reduce the risk of starting the tool
accidentally.
19. Store idle tools out of the reach
of children and other untrained
persons. Tools are dangerous in
the hands of untrained users.
20. Maintain tools with care. Keep
cutting tools sharp and clean.
Properly maintained tools with
sharp cutting edges are less likely
to bind and are easier to control.
21. Check for misalignment or bind-
ing of moving parts, breakage of
parts, and any other condition
that may aect the tool’s opera-
tion. If damaged, have the tool ser-
viced before using. Many accidents
are caused by poorly maintained
tools.
22. Use only proper 7” DiamaPro
Systems tools with this model.
Accessories that may be suitable
for one tool, may become hazard-
ous when used on another tool.
23. Tool service must be performed
only by qualied repair person-
nel. Service or maintenance per-
formed by unqualied personnel
could result in a risk of injury.
24. When servicing a tool, use only
identical replacement parts.
Follow instructions in the Mainte-
nance section of the manual. Use
of unauthorized parts or failure to
follow maintenance instructions
may create a risk of electric shock
or injury.
25. Always use with a DiamaPro
Systems dust shroud.
26. Failure to follow proper use guide-
lines will result in void of
warranty.
GENERAL SAFETY TOOLS
(For All Tools)
WARNING: Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock, re and/or
serious personal injury.
Warning: The body of the machine may get warm after extended
use. If this occurs, turn o the machine and let it cool down to
avoid risk of damaging the unit, or personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
1. Keep your work area clean and
well lit. Cluttered benches and dark
areas invite accidents.
2. Do not operate power tools in
explosive atmospheres, such as
in the presence of ammable liq-
uids, gases or dust. Power tools
create sparks which may ignite the
dust or fumes.
3. Keep bystanders, children, and
visitors away while operating a
power tool. Distractions can cause
you to lose control.
ELECTRICAL SAFETY
4. Power tool plugs must match
the outlet. Never modify the
plugs in any way. Do not use any
adapter plugs with grounded
power tools. Unmodied plugs
and matching outlets will reduce
risk of electric shock. Do not
change the plug in any way. Dou-
ble insulation eliminates the need
for the three wire grounded power
cord and grounded power supply
system.
5. Avoid body contact with ground-
ed surfaces such as pipes, radi-
ators, ranges and refrigerators.
There is an increased risk of elec-
tric shock if your body is grounded.
6. Do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
7. Do not abuse the cord. Never use
the cord to carry the tool or pull
the plug from an outlet. Keep
cord away from heat, oil, sharp
edges or moving parts. Replace
damaged cords immediately.
Damaged cords increase the risk of
electric shock.
8. When operating a power tool
outside, use an outdoor exten-
sion cord marked “W-A” or “W.”
These cords are rated for outdoor
use and reduce the risk of electric
shock.
PERSONAL SAFETY
9. Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use tool while tired or under
the inuence of drugs, alcohol, or
medication. A moment of inattention
while operating power tools may
result in serious personal injury.
10. Dress properly. Do not wear
loose clothing or jewelry. Con-
tain long hair. Keep your hair,
clothing, and gloves away from
moving parts. Loose clothes, jew-
elry, or long hair can be caught in
moving parts.
11. Avoid accidental starting. Be
sure switch is o before plug-
ging in. Carrying tools with your
nger on the switch or plugging in
tools that have the switch on invites
accidents.
