Devinci SPARTAN HIGH PIVOT Manuel utilisateur

TECHNICAL MANUAL

SPARTAN HIGH PIVOT

12 14 15

TABLE OF CONTENT

Cable

Routing

Service

Kit

Assembly

Advices

Suspensio

Set Up

Warranty

Conditions

Frame -

Technical

Specications

FRAME

* DISCLAIMER: We are testing many dierent tires to establish a clearance number that cover a wide spectrum of tires with

appropriate frame clearance. However, it is impossible for us to test all tires and rim combination available on the market,

so be mindful that some combinations may result in slight rubbing if higher than 66mm in actual width.

Technical Specications

Available sizes

S | M | L | XL

HEADTUBE DIMENSIONS

1. UPPER (S.H.I.S) ZS44 1-1/8"Zerostack

2. LOWER (S.H.I.S) ZS56 1.5"Zerostack

BOTTOM BRACKET

3. STANDARD 73MM BSA

4. ISCG MOUNT ISCG O5, xed

MECHANICAL DRIVETRAIN (1X)

5. REAR HUB SPACING O.L.D (Over Locknut Dimension) TA 12 x 157

6. AXLE STOCK IMPORTANT INFOS A. LENGHT: 197 |B. THREAD: 1.0MM |C. PITCH: M12xP1

7. MAXIMUM & MINIMUM CHAINING 38T 28T

8. RECOMMENDED CHAINLINE 56.5mm

9. MIN Q-FACTOR 173mm

SEATPOST AND SEATCLAMP

10. SEATPOST OUTSIDE DIAMETER (OD) 34.9mm

11. SEATPOST LENGTH (S.M,L, XL) 225mm, 250mm 285mm & 300mm

12. SEAT TUBE OUTSIDE DIAMETER (OD) 39.3mm

GEOMETRY INPUTS (BASED ON MEDIUM SIZE)

29er | FORK 170MM | TRAVEL 160MM

13. FRONT SUSPENSION (TRAVEL & SAG) 170mm 33%

14. FORK AXLE-TO-CROWN & OFFSET 581mm 51%

15. REAR SUSPENSION (TRAVEL & SAG) 160mm 33%

16. SHOCK LENGTH & STROKE 205 X 65mm

17. SPRING TYPE COMPATIBILITY AIR & COIL

18. UPPER (OR FRONT) SHOCK HARDWARE DIMENSION Trunnion

19. LOWER (OR REAR) SHOCK HARDWARE DIMENSION 35 X 10mm

20. FRONT & REAR WHEEL GEOMETRY 748mm / 29x2.5 748mm / 29x2.5

21. REAR WHEEL MAX DIMENSIONS 29x2.5*

11 & 12

5 & 6

3 & 4

15 & 16

13 & 14

FRAME

Technical Specications

Q-FACTOR

SPARTAN CARBON 2021+

Step 3

CABLE ROUTING

LEGEND

Housing outside the frame

Housing inside the frame

Seatpost housing

Speed housing

Brake housing

Step 1 | Pass the brake housing through the cavity on the top of the base.

Step 2 | Pull out the housing through the cavity on the outer surface of the

base, attach to the support created for this purpose, then pass the brake housing

through the left opening of the stopper located on the seat tube.

Step 4 | Remove the cap from on the guide located on the left side of the

down tube (use the upper cavity). * Do not replace the cap *

Slide the anti-impact foam tube over the housing up into the down tube.

Step 3 | Slide the brake housing into the top tube.

BRAKE HOUSING

Step 5 | Pass the speed housing through the opening located

below the base.

Step 4 | Take the speed housing out through the cavity under the

base, at the front.

Step 3 | Pass the speed housing under the pulley cap.

Step 1 | Pass the speed housing through the right opening of the stopper

located on the seat tube. Slide the speed housing into the top tube.

Step 2 | Pull out the housing through the stopper located on the left

side of the diagonal (use the lower cavity). * Put back the stop cap *

SPEED HOUSING

Step 1 | Pass the seat post housing through the stopper on the right side

of the diagonal.

Step 2 | Pull out the seat post housing through the bottom bracket cavity.

Slide the anti-impact foam tube over the housing up into the down tube.

Step 3 | Create a loop with the sleeve to reinsert it into the seat

tube. Pull out the seat post cover at the end of the tube.

SEATPOST HOUSING

Step 1

Step 2

Step 3

Step 1

Step 4 | Step 5

Step 2 | Step 4

Step 2

Step 3

Step 2

Step 1

SPARTAN 2021+

CABLE ROUTING

LEGEND

Housing outside the frame

Housing inside the frame

Seatpost housing

Speed housing

Brake housing

Step 1

Step 2

Step 1

Step 2 | Step 3 | Step 1

Step 3 | Step 4 | Step 3

Step 2

Step 1 | Attach the houssing to the tie and the cavity (using a

clip) on the top of the base.

Step 2 | Pass the housing under the shock.

Step 3 | Attach the housing to the guide located on the left side

of the diagonal. Orient to the left side.

GAINE DE FREIN

Step 1 | Pass the housing through the rear opening of the base so

that it pops out at the front.

Step 2 | Secure the housing with a clip under the front of the base using

the cavity created for this purpose.

Step 3 | Pass the housing under the shock.

Step 4 | Fix the housing in the center of the stops of the

diagonal. Orient to the left side.

GAINE DE VITESSE

Step 1 | Pass the seat post housing under the shock.

Step 2 | Pass the housing through the opening located at the

bottom of the seat post all the way to the top. Pull out the housing at

the end of the seat tube.

Step 3 | Attach the housing to the guide located on the right side of

the diagonal. Orient to the right side.

GAINE DE TIGE DE SELLE

*Follow the seat post manufacturer's instructions for adjusting the length

of the housing.

REAR AXLE

(20 N∙m)

6.7 N∙m

COLLAR

6 N∙m

UPPER SHOCK BOLT

(14 N∙m)

CL PIVOT

(14 N∙m)

LOWER SHOCK BOLT

(14 N∙m)

DO PIVOT

(22 N∙m)

DERAILLEUR

HANGER

(25 N∙m)

BL PIVOT

(14 N∙m)

CHAIN GUIDE

(6 N∙m)

WL PIVOT

(14 N∙m)

WARNING:

MAKE SURE TO

CAREFULLY READ THE

ASSEMBLY

INSTRUCTIONS AND

CLEANING

INSTRUCTIONS NOTES

ON NEXT PAGE.

DO PIVOT

WL PIVOT

BL PIVOT

CL PIVOT

Revision

PCB-044

SPARTAN CARBON 29 HP

SERVICE KIT

ASSEMBLY INSTRUCTIONS:

THOROUGHLY CLEAN THE INTERIOR OF EACH BEARING HOUSING TO REMOVE ANY DIRT OR OLD GREASE;

APPLY HIGH QUALITY WATERPROOF GREASE ON THE INSIDE FACE AND INSIDE DIAMETER OF ALL BEARING

HOUSINGS BEFORE PRESS-FIT;

APPLY HIGH QUALITY WATERPROOF GREASE TO ALL PIVOT PARTS THAT CONTACT WITH THE INNER

DIAMETER OF THE BEARINGS.

APPLY HIGH QUALITY WATERPROOF GREASE TO ALL NON-THREADED METAL-TO-METAL INTERFACES (EX.:

PLANAR FACE OF THE PIVOT SPACER THAT CONTACTS THE LATERAL FACES OF THE FRONT TRIANGLE WL

PIVOT). THESE INSTRUCTIONS ALSO APPLY TO THE SHOCK ASSEMBLY;

UNLESS OTHERWISE SPECIFIED, APPLY BLUE LOCTITE 242 ON ALL THREADS BEFORE ASSEMBLY TO THE

SPECIFIED TORQUE VALUE;

TO PREVENT DAMAGE TO THE FRAME, THE SEATPOST MUST HAVE A MINIMUM INSERTION IN THE SEAT

TUBE.

CARBON FRAME:

SMALL / MEDIUM / LARGE / X-LARGE - 100mm INSERTION

*ALWAYS VERIFY CONNECTOR CLEARANCE BEFORE FULLY INSERTING A DROPPER POST.

FRG ADJUSTABLE

: THIS DESIGN ALLOWS RIDERS TO CHOOSE BETWEEN A LOW OR HIGH POSITION. WITH

FRG ADJUSTABLE TECHNOLOGY, YOU CAN FINE-TUNE YOUR RIDE TO PERSONAL TASTES OR SPECIFIC TRAIL

TYPES USING A FLIP-FLOP PIVOT MECHANISM THAT SLIGHTLY CHANGES THE BIKE'S GEOMETRY AS SHOWN

BELOW.

CLEANING INSTRUCTIONS:

IT IS A WELL KNOWN FACT THAT A CLEAN BIKE PERFOMS BETTER. DEVINCI RECOMMENDS WASHING YOUR

BIKE REGULARLY USING A BRUSH AND SOAPY WATER. HOWEVER, DEVINCI DO NOT RECOMMEND THE USE

OF A PRESSURE WASHER, SINCE THIS MAY SIGNIFICANTLY REDUCE THE SERVICE LIFE OF BALL BEARINGS.

EVEN THOUGH OUR BALL BEARINGS ARE EQUIPPED WITH HIGH QUALITY DOUBLE-LIP SEALS, HIGH

PRESSURE WATER CAN STILL PASS THESE SEALS AND REMOVE THE GREASE INSIDE THE BEARING. THIS

MAY CAUSE PREMATURE CORROSION AND WEAR OF THE BALL BEARINGS.

Revision

PCB-044

SPARTAN CARBON 29 HP

SERVICE KIT

Table des matières

Autres manuels devinci Vélo

devinci

devinci E-MILANO Manuel utilisateur

devinci

devinci AC Manuel utilisateur

devinci

devinci E-TROY Manuel utilisateur

devinci

devinci DJANGO CARBON 2021+ Manuel utilisateur

devinci

devinci E-TROY Manuel utilisateur

devinci

devinci TROY 8402 Manuel utilisateur

Manuels Vélo populaires d'autres marques

RAMBO

RAMBO R1000X2M-FF-BFD Manuel utilisateur

Vermeiren

Vermeiren SAFARI Manuel utilisateur

Velec

Velec A2/36V Manuel utilisateur

Coswheel

Coswheel A-ONE Manuel utilisateur

Betzold

Betzold 97869 Manuel utilisateur

Cervélo

Cervélo S3 2019 Manuel utilisateur

Tenways

Tenways AGO X Manuel utilisateur

Festo

Festo EGSC-BS-KF Manuel de la liste des pièces

Gio Electric

Gio Electric H1 Volt Manuel utilisateur

GOGOBEST

GOGOBEST GM30 Manuel utilisateur

DAHON

DAHON CIAO - 2009 Manuel utilisateur

Aprimatic

Aprimatic ONDA 500 Guide de démarrage rapide

MV Agusta

MV Agusta Lucky Explorer GRAVEL Manuel d'instructions

Greyp

Greyp G6 Series Manuel utilisateur

Babboe

Babboe Carve-E Manuel utilisateur

Huka

Huka orthros Manuel utilisateur

Xtracycle

Xtracycle Stoker 2021 Manuel utilisateur

APRILIA

APRILIA DORSODURO 750 ABS 2015 Manuel utilisateur

devinci SPARTAN HIGH PIVOT Manuel utilisateur

Manuels Vélo populaires d'autres marques