Camera Installation
The camera can be mounted by using either the bracket mount on the top or bottom (see part description 2).
The bracket mounts accept standard photographic mounting bolts (1/4" BSW or 20 UNC).
Precautions
Connecting to the Power Source and Video Output
Ensure the bracket, screws (inc. wall plugs, if
used) and mounting surface can support the
load of the camera and bracket.
Specifications
Video Output
The camera operates in either dual power (24 VAC / 12 VDC) or main power (220V).
Connections are indicated in the rear panel of the camera.
The power supply must be stable power source and should only be installed by qualified personnel.
Connect the 75 Ohm coaxial cable to video output (see part description 8).
AC/DC Low Voltage (24VAC / 12VDC)
AC Voltage (220V)
TV System
Image Sensor
Resolution
Scanning
Frequency
Effective Picture
Element
Video Output
S/N Ratio
Storage Temperature
Operating Temperature
Power Consumption
Power Source
NTSC / PAL
NTSC
PAL
976(H) x 494(V)
NTSC
PAL
NTSC
PAL
976(H) x 582(V)
60Hz
50Hz
700 TVL
1.0Vpp Composite Output
220 VAC ±10% (50/60 Hz)12 VDC ±10% / 24 VAC ±20%
Normal:2.2W Normal:2.2W
Dimensions 63mm (W) x 57mm (H) x 120.2mm(L)
-10°C ~ +50°C
-20°C ~ +60°C
2nd Video Output Yes (supports installation check)
Minimum Illumination
Auto White Balance Range
White Balance Control
Backlight Compensation (BLC)
Sync System
Privacy Zone
Motion Detection
Shutter Speed
Shutter Control
1/60 ~ 1/100000
1/50 ~ 1/100000
ATW / Manual / Push / Push Lock / USER1,2
Indoor：1800K~10500K / Outdoor：6500K~10500K
INT /LL
4 Areas
Functional Specifications
General Specifications AC/DC Dual Power Model AC Mains Power Model
Full Range
AGC Gain Control 44.8 dB
Day/Night SDN(AUTO ,COLOR ,NIGHT)
Adaptive Tone Reproduction (ATR) OFF / LOW / MID / HIGH
High-Light Compensation (HLC) ON/OFF
Up to 15 Masks
Digital Noise Reduction
Digital Zoom
DIS
3D DNR
255X Max
On/Off
Gamma Compensation 0.45
AUTO/MANUAL/FIX
Mirror OFF/V-FLIP/H-FLIP/HV-FLIP
Defog ON/OFF
Sony 1/3" Super HAD-II
V531-CR035-S00
VER. 11/2015
CCD Box Camera
Instruction Manual
www.devieweurope.com
.
Never attempt to disassemble or modify the camera.
Any modification could lead to damages that are not
covered by the guarantee.
Make sure the power source is switched off and
disconnected before installation. Refer servicing to
qualified personnel only.
Do not expose or operate the camera in wet areas.
Moisture may damage the camera and also increase
the danger of electrical shock.
Do not attempt to aim the camera at the sun or other
extremely bright objects. This may cause damage to
the CCD and the void of warranty.
Do not touch the lens or the CCD by hands while
installing or adjusting the camera.This may cause
damage to the camera.
This product must be installed and maintained in accordance with good installation practices by qualified personnel only.
To prevent damage to your camera or injury to yourself or to others, read and comply with the safety precautions as follows:
regulated power supply and the wiring should
be used for the appropriate input terminal.
To prevent fire or electrical shock, use only
700 TVL Day / Night
Color Camera
Side View
Rear View
11
1. Back Focus Adjustment
2. Bracket Mount
3. OSD Control
4. Video Lens Drive Terminal Block
5. Day/Night Switch
6. Power Input Terminal Block
(DC/AC Low Voltage)
7. BNC Composite Video Output
8. Power LED Indicator
9. AC Power Input Socket
(AC Mains)
10. CCD Sensor
11. DC Lens Connector
Top View
12
Front View
10
7
8
6
4
5
37
9
12 12
8
100~240VAC~ 50/60Hz
LAMP
LAMP
LAMP
Parts Descriptions
12. Second Video Output
Bracket Mount
Protective
Cover
GND
+12V
VIDEO
GND
D/N SW
VIDEO OUT
Power Input
Terminal
Video Output
Power Input
Terminal
POWER
VIDEO OUT
100~240VAC~ 50/60Hz
GND
+12V
VIDEO
GND
LAMP
0.3 Lux (F1.2, 50 IRE,AGC ON)
50 dB (100 IRE, F1.2)
