Detex VALUE SERIES V40 x EB Manuel utilisateur

FV40 / V40 x EB, EH, EHxR, EX

P/N: 100482

P/N: 100088

Mortise

Strike Shim

98 Strike *, P/N: 100855-1

P/N: 100480

P/N: 100234-1

Mortise Strike

Strike Shield

P/N: 101899

P/N: 100212

2" Narrow Stile

Plastic Template

P/N: 100481

101275 Page 1

Fillerplate SubAssembly (EX x CD)

Owner's Copy

P/N: 104356-1 (3-0)

P/N: 100783

Hex Nut

P/N: 101815-X (4-0)

P/N: 101810-X (3-0)

Pushpad Wrap

Fillerplate SubAssembly

RIM

99 Strike *, P/N: 100855-2

P/N: 101805-1

Centercase Cover

Mounting plate

Subassembly

P/N: 100696-1

Strike ShimNon-Roller Strike

Standard

Plastic Template

P/N: 104350-X

Plastic Template

Centercase/Pushpad SubAssembly

Use for ease of installation

Parts Check List

Fillerplate SubAssembly (EX x HD)

(Electrified Models)

Fillerplate Subassembly (EX x LD)

Fillerplate SubAssembly

P/N: 104358-X

P/N: 104357-1 (3-0)

P/N: 104355-1 (3-0)

P/N: 100783

P/N: PP-5567

Hex Nut

9V Battery

Hex Key

P/N: 100450

Endcap Bracket

U.S. PATENT NUMBERS:

6009732

6205825B1

6532777B2

INTERNATIONAL PATENT NUMBER:

PCT6009732

P/N: 101844

P/N: 101822

Endcap

P/N: 101821

INSTALLATION INSTRUCTIONS FOR DETEX VALUE SERIES® V40 RIM PANIC HARDWARE,

FV40 RIM FIRE EXIT HARDWARE AND "H" MODELS (HURRICANE)

Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045

(830)629-2900 / 1-800-729-3839 / Fax (830)620-6711

E-MAIL: detex@detex.com INTERNET: www.detex.com

101275 November 09, 2007

-GlassBeadKit

-SexNuts

-TamperKit

- Double Door Strike Kit

-KeyStopKit

- Narrow Stile Kit

See

Optional Accessories

For:

Mortise cylinder not included with device.

Standard Yale type cam required.

Note: Parts listed above will vary

according to product configuration.

*Narrow Stile "NS" option

Latchbolt Monitoring

Centercase Assembly

P/N: 104354

P/N: 104357-3 (4-0)

P/N: 104355-3 (4-0)

P/N: 104356-3 (4-0)

L9 = Less 9v Battery

SI = Status Indicator "ON"

frame engages at

Minimum door stile 2" (51mm)

RHR Door

Inside Face

Floor

Finished

40"

101275 Page 2

RHR Door

Reference

Stop Face

Horizontal

LHR Door

Inside Face

LHR Door

Face

Mullion

Door Must Not Bind

NOTE: 750mm MAXIMUM DOOR WIDTH OPENING FOR EUROPE FOR 36" DEVICE

(1000mm MAXIMUM DOOR WIDTH OPENING FOR EUROPE FOR 48" DEVICE)

THE SAFETY FEATURES OF THIS PRODUCT ARE ESSENTIAL TO ITS COMPLIANCE WITH EN 1125.

NO MODIFICATION OF ANY KIND, OTHER THAN THOSE DESCRIBED IN THESE INSTRUCTIONS ARE PERMITTED.

Door Must Swing Freely Door Must Not be Warped

Surface strike possible

Mortise strike recommended

least (3) screw

threads.

Door Must Not Sag

Door Skin

Blind Rivet Nut

Doors and frames with walls having a structural thickness (metal skin

plus reinforcement, or solid wood) to engage less than (3) full

screw threads, are considered unreinforced for hardware.

!!!CHECK BEFORE STARTING!!!

Unreinforced Doors: Use Sex Nuts and Bolts

Fasteners for unreinforced openings are not supplied by Detex.

Unreinforced Frames: Use Blind Rivet Nuts (see sketch)

Minimum door stile 4-1/2" (114 mm)

Wide Stile (Surface Strike)

Template drawings provide door and frame

door and frame preparation.

structural and dimensional specifications for

Narrow Stile

Reinforced door or Reinforcement

(2) Mortise Cylinder NOT Provided.

Note: (1) Fastener selection will vary per catalog configuration and kits ordered.

PPH

PFH

PPH

PFH

Screw Driver

Safety Glasses

Level

Sex Nut

#1/4-20

#10-32

Power Drill

Sheetmetal Screws

#1/4-20 x 1"

#6 x 1"

#10 x 1"

#1/4-20 x 1/4"

#10-24 x 5/8"

#6-32 x 3/8"

#14 x 1"

Center Punch

101275 Page 3

Tape Measure

Hammer

Hack Saw

Used on Strike, Mounting plate, and Endcap Mounting Holes

Recommended on Fire Rated Wood and

9/32" Interior Door Face -----

----

13/64" Interior Door Face

5/16" Exterior Door Face

3/8" Exterior Door Face

-----

Pencil

Tools Required

----

Used on Strike Hook Mounting Holes

Unreinforced Hollow Metal Doors

Recommended on Fire Rated Wood and

Used on Mounting plate and Endcap Mounting Holes

#7 or 13/64"

9/64"

-----

#25 or 9/64"

-----

#10-24 Tap

#1/4-20 Tap

-----

Metal Applications

Used on 99 Strike Center Mounting Hole

Used to Mount Centercase Cover and Endcap

Used to Fasten Centercase Unit onto Mounting plate

Used on 99 Strike Center Mounting Hole

Used on 98 Strike Shield Mounting Holes

PFH

#6-32 x 5/8"

Machine Screws

Fastener Table

Drill Bit Tap Wrench

#36 or 7/64 #6-32 Tap

Comments

Use Either Machine Screws, Sheetmetal Screws,

Used on 98 Strike Shield Mounting Holes

or Sex Nuts

Self-drilling Screws

No pilot hole necessary for

self-drilling screws

101275 Page 4

Strike holes (2)

For 1/4-20 machine screws

drill #7 holes

No pilot hole necessary

for #14 self-drilling screws

(see fastener table)

screws or #14

Fasten tightly with

1/4-20x1" machine

lockwashers and

self-drilling screws

Mark centerline

finished floor

40 inches above

for unit

two 1/4-20x1" machine

screws or #14

self-drilling screws

Fasten loosely with

label temporarily

if necessary.

(see outside

trim instructions)

Trim input hole

Slide99strikelocator

into mounting plate.

(ifusinga98strike,see

98 STRIKE INSTALLATION page)

holes

Mounting plate holes (2)

For 1/4-20 machine screws drill #7 holes.

For #14 self-drilling screws no pilot holes

necessary.

For sex nuts drill 3/8" holes.

(see fastener table)

and strike holes

Mark mounting plate

Punch marked

Mounting plate Hole

Strike holes

to mark trim hole

Mounting plate

hole

If necessary, remove

RECOMMENDED

101275 Page 5

When using Pushpad Wrap with text

(LHR handing shown)

verify handing before installing wrap.

Peel off backing

to expose tape.

IMPORTANT:

Install Pushpad Wrap.

by snapping in place.

Verify wrap is secured

Position cam as shown

Insert centercase into slots

of centercase mounting plate,

depress pushpad, rotate

toward door.

MUST BE INSTALLED!

to mounting plate

Fasten rim device

with 1/4-20 x 1/4" PPH

DOOR

101275 Page 6

(Call factory at (800) 729-3839 for assistance)

(Cut-Off procedure if required)

CHECKING FOR DEVICE CLEARANCE

onto extrusion

Slide endcap assembly

Secure

Protect wires

during cutting

Place battery in endcap.

Battery should not contact

circuit board.

Battery

4" 10"

Max. Cut-Off

Length (L) inches

beyond edge of cut fillerplate.

Reassemble electronics

Electronics may extend

36" Unit

after cutting.

48" Unit

longer than the standard

REMOVE battery clip

for CUT-OFF lengths

Procedures for Maximum Cut Down Lengths

REMOVE electronics

prior to cut down

Caution Required-Special Handling

with

tape

Align fillerplate

FLUSH to extrusion

prior to cutting

CAUTION:

Check for device & door

frame clearance. If no

cut-off needed, proceed to

MORTISE CYLINDER INSTALLATION

Cut fillerplate & extrusion to

desired length*

Install battery

(where required)

Electrified

model

Cut fillerplate & extrusion to

desired length*

Protect wires

during cutting

6in

2in

12 in

8in

Secure

with

tape

36" Unit

Type 48" Unit

Length

Align fillerplate

prior to cutting

FLUSH to extrusion

cut-off length

101275 Page 7

cylinder with

Install mortise

hex nut provided

the fillerplate

subassembly

Slide/remove

NOTE:

installing slide in fillerplate.

(2) Turn key max CCW before

(3)Useacylindercollarwheninstalling

(4) Reinstall fillerplate subassembly

(1) All cylinder spacers must be used.

a 7-pin mortise cylinder.

and cylinder collar (not included)

length with spacers (provided)

Adjust for LONGER cylinder

Be careful when installing fillerplate assembly not to damage cable

MORTISE CYLINDER INSTALLATION

PRECAUTIONARY NOTE:

See View A

Longer cylinder

Cylinder collar optional

(see note 3)

(Detex p/n: ECL-1595)

CAUTION:

Tighten with hand

tools only. Do not

overtighten

View A

Install cable assembly

For Latch Bolt Monitoring (LBM) units only

Refer to switch options pages

101275 Page 8

for added security

Slide and mount endcap

to endcap bracket with two

1/4-20x1" PPH machine screws

or #14 self-drilling screws.

DO NOT OVERTIGHTEN

Slide fillerplate & endcap bracket into

extrusion & level pushpad assembly.

Note: Endcap Bracket must bottom-out

on extrusion. DO NOT REMOVE

NYLON SPACER ON BACK OF

BRACKET!

see HARDWIRE TRANSFER OPTIONS page

For 1/4-20 machine screws drill #7 holes.

For #14 self-drilling screws no pilot holes

necessary.

For sex nuts drill 3/8" holes.

Install (2) 6-32 FH Screws

IMPORTANT:

With pushpad assembly level,

secure the endcap bracket to door

by tightening the factory installed

self-drilling screw.

101275 Page 9

extend its life.

Care and Maintenance:

The Detex Value Series® devices are designed to provide many years of maintenance

free service under normal usage. Periodically inspect and lubricate the unit to with hand tools only.

Install cover with 6-32

machine screws. Tighten

Fasten rim device to mounting

plate and door with 1/4-20x1"

machine screws(drill #7 holes)

or #14 self-drilling screws

center screw.

strike engagement BEFORE

Align the 99 strike with

Firmly tighten screws

the latchbolt.

marking and drilling for

Check device function and

(use shim if necessary)

Note:

Mark and drill center hole.

9/64" for 10-24 machine

screws.

No pilot hole necessary

for #10 self-drilling screws.

(see fastener table)

Secure the 99 strike.

Deadlatch

99 strike

For Hurricane Models

(see Hurricane kit)

N.O. contactViolet

BrownPin 1 Common Pin 4

Contacts rated at 1.0A @ 30VDC or 0.5A @ 125VAC

Pin 5

Pin 6

Normally Closed

Yellow

Gray-Green

Pin 2

Pin 3

Normally Open N.O. contact

101275 Page 10

Violet

---- ----

Figure 3

P1 detail

P1 (see Fig. 3)

Figure 2

Battery Connector

(Standard)

(P1 wire usage)

Wiring Detail

Remote Signal

Table 5

(EHxR)

Bypass/Remote Signal

Remote Bypass

The device flashes one red LED and one beep about every 45 seconds

The Device gives no indication of battery being low.

Off (factory set)

Protect wires

Switch selections must be made before applying power or installing battery (See Figure 1)

Table 2

See

See Table 1

Alarm sounds until turned off with key.

Unit sounds alarm as long as door is open.

Extended bypass is enabled.

Alarm turns off 2 minutes after door is closed

Auto Rearming Feature Setting

Status Description

Note: AC power must be applied

Table 3 (EH models only)

Disable Auto rearm

On (factory set)

Off

Disable Low Battery

Table 2

Status Description

The Device gives no indication of armed or disarmed status.

Status Indicator

Off (factory set)

SWITCH OPTIONS

Table 1

Disable

AUTOREARM

DisLo Bat

INDICATOR

STATUS

Brown Common

Open

Closed

Yellow

Gray-Green

Install armored cable kit (if required)

V40 x EX Wiring Assembly

Fillerplate subassembly

Wire Color Connection

Endcap bracket

Endcap

(see Table 5)

Figure 1

See Table 3

(jumper w/L9)

TheDeviceflashesredorgreenLEDevery3seconds.

Red indicates armed status and green indicates disarmed.

12/24V AC/DC External Supply

(black wire)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Detex Système de sécurité

Detex

Detex EAX-500 Manuel utilisateur

Detex

Detex EA-500 Manuel utilisateur

Detex

Detex Designed Security ES411 Series Manuel utilisateur

Detex

Detex EAX-3500 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur