Detection Systems DS7400Xi Manuel utilisateur

DS7400Xi Control/Communicator

Terminal Wiring & Programming

P/N 44128C DS7400 Programming

.DS7400Xi Panel Wiring & Programming

44128C DS7400 Programming

Control Terminal Wiring

DS7400Xi Panel Wiring & Programming

Before servicing, remove all power including

the transformer, battery and phone line.

A complete functional test is required after

any programming.

Incorrect connections may result in damage

to the unit.

System is Power Limited except for battery

terminals. All wiring entering the enclosure

must be power limited.

DS7400Xi Panel Wiring & Programming

EARTH GROUND:Must be connected to a good earth ground

such as a cold water pipe and also connected to the cabinet

cover using the supplied wire jumper.

A/C INPUT: Use U.L. listed, 18 VAC 50 VA, class 2

transformer. Model TR-1850 requires 50/60 Hz. unswitched

dedicated outlet. Do not share.

ALARM OUTPUT: Provides 12 VDC, special application, up to

1.75A for powering bells, sirens drivers, etc.

Function programmed in address 0146

AUXILIARY POWER: Provides 12 VDC, special application,

up to 1.0A for powering detectors.

A/C Power Indication LED

DS7400Xi Panel Wiring & Programming

OPTIONS BUS:

Used for options such as the ARDIS communications

module, the DS7420i Dual Phone Line module, etc.

Also for keypads #11 - #15.

For Commercial Fire Mode: Option Bus Wiring must

be run in conduit if run outside the enclosure.

DS7412 RS-232 Interface Module

DS7488 Octal Relay Module

DS7489 Octal Open Collector Module

DS7420i Commercial Fire Module

DS7416 ARDIS Transmitter

X7410 X10 Interface Module

Options Include:

DS7400Xi Panel Wiring & Programming

RBGY

1211109

KEYPAD BUS*:

Up to 15 keypads**

may be used.

Can be “home-run”

or “daisy-chained.”

Keypads #1 - 10

*= Maximum wire length each: 1000 ft. (305 m).

Max. wire length total in system: 6000 ft. (1830 m)

when using #22 AWG (.8mm) or #18 AWG (1.0mm)

cable.

** = Keypads #1 - 10 connect to the Keypad Bus.

Keypads #11 - 15 connect to the Options Bus.

Shared cable is not recommended for keypad

bus, multiplex bus, options bus, telephone, or

siren wiring.

DS7400Xi Panel Wiring & Programming

Phone Line:

(RJ-31x or 38x)

T TH RH R

GBSR

16151413

House

Telephone

Company

DS7400Xi Panel Wiring & Programming

17 18 19 20 21 22 23 24 25 26 27 28 29 30

PO1 PO2 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 -L + L + L + L +

ZONES 1-8 : Intended for connection of Normally Open or

Normally Closed alarm contacts. May be used for compatible

2-wire smoke detectors. These zones require a 2.21KW resistor

(P/N 25899) at the end of the loop.

Power is momentarily removed from L+ after a [PIN]+[System

Reset] or during fire verification.

Zone 1-8 assignments are programmed in addresses 0018-0025.

PROGRAMMABLE OUTPUTS:

PO1 shorts to aux. power negative when activated. PO1 can sink up to 1.0A.

PO1 function programmed in address 0147.

PO2 supplies 12 V and up to 500 mA when activated.

PO2 function programmed in address 0148.

DS7400Xi Panel Wiring & Programming

Disconnect wire jumper from terminal 4 to inner housing of Bell Box.

(Prevents a ground fault condition)

Connect wiring between control and Bell Box as shown next slide.

To use AB-12 Bell/Housing, cut jumper wire “JP1” on control.

EOL used in AB-12 Bell / Housing must be 27K ohms.

Program Zone 8 as 24-hour zone by programming it to follow zn function 7.

(Program address 0025 should be 07)

Do not change default programming of zone function 7.

(Program address 0007 should be 22)

Wiring & Programming for Installations

using Ademco AB-12 Housing

DS7400Xi Panel Wiring & Programming

1Bell

To Earth Ground Terminal 1

To Control Loop Positive Terminal 29

To Control Zone 8 Input Terminal 30

To Control Alarm Output Terminal 5

To Control Alarm Output Terminal 6

EOL

27kW

Inner Bell Housing

Outer Bell Housing

Cut this Jumper - JP1

Control/Communicator

DS7400Xi Panel Wiring & Programming

Autres manuels pour DS7400Xi

Table des matières

Autres manuels Detection Systems Capteur de sécurité

Detection Systems

Detection Systems DS433i Manuel utilisateur

Detection Systems

Detection Systems DS1525 Manuel utilisateur

Detection Systems

Detection Systems Security Escort SE88 Series Manuel utilisateur

Detection Systems

Detection Systems DS7060 Manuel utilisateur

Detection Systems

Detection Systems DS1520 Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur