DesignTech Secure start 28622 Manuel utilisateur

Secure Start Model 28622

Add On Remote Control Car Starter Installation Instructions

v 0.2

Tools required to install the remote starter unit:

Wire Cutters/Strippers Soldering Iron Pliers

Testmeter Electrical tape Screwdriver Drill

We highly recommend that all connections be soldered for reliability.

Parts List:

Remote Start odule Control Harness

(10 position)

Parts Kit in plastic baggy:

30 A Fuse Hood Pin Switch Set 2 Cable Ties

On/Off Control Switch Warning Label Ring Terminal

Wiring Diagram

WARNING

This car is equipped with a remote control starting device.

Disable before working on car!

AVERTISSEMENT

Co véhicule est équipé d’un systéme de démarrage á distance. Mettez-le hors

fonctuin avant d’eflectuer toule opération d’entretian ou de répanation!

Please Read Completely Before Beginning

Congratulations on your purchase of the Secure Start Add On Remote Car Starter. This remote car starter system allows you to

start the car by remote control from the comfort of your home or office in order to cool it down in the summer or heat it up in the

winter.

The Secure Start Remote Car Starter is for automaticl transmission vehicles only. It is an extremely sophisticated system with

multiple built-in safety and security features.

The Secure Start Remote Car Starter:

• Will start your car by remote control, and run the heater, defroster, or air conditioner to warm up or cool down the car.

• Is designed to start the car if it is in park, and only if the hood is closed.

• Will attempt to start the car for up to six seconds, but no longer (to avoid damage to the starter motor). Should the car

not start, or if it stalls after starting, the remote starter will make two further attempts to start it.

• Will not let the car be driven without the key in the ignition.

• Shuts itself off automatically after 10 or 15 minutes (programmable) if you forget to come out to your car.

• Will shut off if the brake pedal is pushed, or the hood is opened - unless the key is in the ignition and in the “run” position.

• Allows you to remove the key while leaving the car running with the doors locked for up to 10 or 15 minutes utilizing the

QUICK STOP

option. (See Separate User Tip Sheet)

• Is quality engineered, microprocessor controlled, and made in the USA to provide many years of reliable use.

• Comes with a 2 year warranty.

Power Harness

Control Harness

6 Power &

Ignition wires

DesignTech International, Inc. • 7 55 Cameron Brown Court • Springfield, Virginia 22153 USA • 703-866-2000 or 800-337-4468

Color Function Type Required

Pink Power (+12V) Input Yes

White Accesory / Lights Relay Output Yes

Yellow Starter Relay Output Yes

Blue Ignition 1 Relay Output Yes

Green Ignition 2 Relay Output Possible

Black Ground Input Yes

Color Function Type Required

Yellow/Green Alarm Control (+) 400 mA No

Green/White Sensor IN Relay No

Brown Accessory Pulse (-) 400 mA No

Brown/White Alarm Disable (-) 400 mA Possible

Gray/Black Sensor OUT Relay No

Color Function Type Required

Red/Black Diesel Input Input No

Red/White Remote - Input Yes

Green Tach Input No

Violet Hood - Input Yes

Orange Brake + Input Yes

LED

Plug-in Control Switch

Left

White Button Right

Red Button

On cars with airbags, you may notice bright yellow tubes or

harnesses underneath the steering column area. DO NOT

tamper with these wires in any way, to prevent personal

injury and/or damage to the air bag system.

Battery gases are explosive. Do not smoke while working near the car’s

battery.

Note: Some installers connect a battery charger to the

vehicle’s battery during installation. This is fine, but it must be

removed before running the vehicle under remote control.

When working the wires through the car’s firewall, be sure to protect

them from sharp metal edges and from hot surfaces on the engine.

INSTALLATION INSTRUCTIONS

1. Before You Start

Take the time to read through the whole installation manual.

Always leave one window open to avoid locking your keys in your car.

IMPORTANT: After having read the entire manual, start the installation by

putting the yellow WARNING STICKER in the engine compartment. Choose

a surface that is clean and readily visible when the hood is open.

POWER & IGNITION HARNESS

The remote starter module will be installed under the dash once all wiring

has been completed. Do not mount the module at this time! You will

need to check the diagnostic light (LED) as the installation progresses.

Locate (or drill) a hole in the firewall to run the VIOLET, and GREEN wires

of the Control Harness and the PINK wire of the Power harness through

into the engine compartment. The remaining short wires stay in the pas-

senger area. Leave about a foot of the wire harness under the dash for

ease of working and visual access to the diagnostic light.

Note: Always connect the Pink and Black wires before connecting any

of the other wires.)

2. Black Wire (16 AWG) - Ground

Connect the BLACK wire to a very good, clean chassis ground in the

driver’s kick panel area. Use the small red ring terminal if needed. The

metal bracing around or beneath the dash board is not adequate.

3. Pink Wire (12 AWG) - Power (+12V)

Connect the ring terminal at the end of the short PINK wire to the +12 volt

terminal of the battery. Run the long pink wire through the firewall of

your vehicle. Join the remaining ends of the power wire together by

soldering them. Tape with electrical tape to leave no exposed wires.

Alternatively, you may wish to use a yellow butt terminal, but we recom-

mend soldering. After all of your connections are complete, insert the

30 amp green fuse into the holder. As the power wire is connected the

LED will blink once.

Note: Failure to properly install the fuse holder and 30 amp fuse to the

pink wire voids all product warranties.

Ignition Key Diagram or Steps 4-7

The vehicle’s wires are found coming off of

the key switch. Remove the panel under the

steering column to access these wires.

4. Blue Wire (14 AWG) - Ignition 1

Connect the BLUE wire to the ignition 1 wire of your vehicle. This wire will

measure +12V on the test meter in the “run” and “start” position, and is

off (ground) in the “lock/off” and “accessory” position.

5. Green (14 AWG) - Ignition 2

Connect the GREEN wire to the second IGN2 wire (if applicable) of your

vehicle. This wire will power the heater/air conditioner (in most cars). This

wire will measure +12V on the test meter in the “run” position only.

6. White Wire (14 AWG) - Accessory

Connect the WHITE wire to the accessory wire which is +12V in the “run”

and “accessory” position, but off (ground) in the “start” and “off” posi-

tions.

7. Yellow (14 AWG) - Starter

Connect the YELLOW wire to the starter wire. This wire will measure +12V

on the test meter in the “start” position only.

Note: Nissan vehicles have two starter wires. Connect both starter wires

to the YELLOW wire.

8. Plug-In On/Off Switch

Plug the ON/OFF control switch into the module just to the right of the

power wires. Use a 1/4” drill-bit for the mounting hole.

Note: Mount the control switch in the dash so that it is easily accessible

and so that the “ON” position is facing upward. Make sure there is

enough clearance behind the mounted switch for the wire connections.

Connection of this switch is mandatory.

Control Harness (All wires are the smaller 18 AWG size)

9. Red / Black Wire Diesel “wait to start” Control Harness

This wire is only used in diesel vehicle applications This wire should be

hooked up to the “wait to start” light’s switched wire behind the dash. If

option 9 is set, this wire wire will feed information to the remote starter as

to when to crank the vehicle over.

10. Violet Wire - Hood Pin Switch - Control Harness

The hood pin switch MUST be installed with

the remote starter. It prevents operation

of the remote starter when the hood is

open and is used to initialize the unit. Con-

nect the VIOLET wire to the hood pin

switch using the red connector.

Note:If you already have a hood pin

switch which is being used by a car alarm

system, you may share the wiring -- but

be sure to diode isolate each wire going

to the hood pin switch with the bands of

diodes pointing towards the pin switch

as shown at right.

11. Orange Wire - Brake Shut-off - Control Harness

Connect the ORANGE wire to the brake wire which receives +12V when

the brake pedal is depressed. This wire must be connected. It arms a

critical safety feature which disables the remote starter when the brake

pedal is depressed.

Note: In some cars, the ignition must be in the “on” position to test the

power in the brake wire.

12. Initializing the Remote Starter

BEFORE THE CAR WILL START FOR THE FIRST TI E, YOU UST INITIALIZE THE

RE OTE STARTER

A. Turn the control switch on.

B. The Remote Start odule requires the installer to open the hood

and then press and hold the brake pedal. Note: The dash lights will

come on if the unit is not initialized.

C. While depressing the brake (with the engine off and the hood open)

turn the ignition key to the “RUN” (not “start”) position.

D. Put the car in gear from the “PARK” position.

E. Put the car back in “PARK” and release the brake.

F. Turn the key off and remove key.

WARNING

This car is equipped with a remote control starting device.

Disable before working on car!

AVERTISSEMENT

Ce véhicule est équipé d’un systéme de démarrage a distance. Mettez-le

hors fonction avant d’eflectuer toute opération d’entretien ou de réparation!

How to share a hood pin

switch with an alarm

To Remote Starter

Note: Confirm initialization by turning the ON/OFF control switch “OFF”

and then “ON”. The red LED on the Remote Start module will flash once

immediately as the switch is flipped from the “OFF” to the “ON” position.

If the unit is not initialized then the dash lights will come on (the Remote

Starter powers up the ignition wires) when the brake is depressed when

the hood is open when the control switch is on. REPEAT STEPS A THROUGH

F. See the purple colored Trouble Shooting Sheet if necessary.

13. Green Wire - Tach Input - Control Harness

The Remote Starter has two ways of monitoring the car during the start-

ing process. Both ways will ensure a clean, accurate start. Read about

both methods before deciding which one to use. Normally you should

try the “No TachTM” method first.

“No TachTM” Starting

This starting method does not require the connection of the GREEN tach

wire. This method will start the car by reading the car’s voltage before

attempting to start, and then looking for a voltage increase when the

alternator kicks in. This feature automatically takes into account voltage,

temperature, and the time since the vehicle was last run. The “No-TachTM”

starting is preset at the factory and you can skip step 13A if you would

like to use it. Note that if the vehicle is hard to start, set option #3 (step 22)

for “extended crank.”

Tachometer sensing

If the vehicle is generally hard starting (requiring a cranking time of more

than 1 second) you will get more accurate starting with the tachometer

sensing starting method. This method starts the car by reading the en-

gine speed (tach) information from a wire under the hood. If you choose

tachometer sensing, connect the GREEN (18 awg) wire to the car’s tach

wire under the hood (normally the negative side of the coil or tach out-

put of coil pack). After you have connected the GREEN wire, you need

to teach the Remote Starter the vehicle’s tach rate at idle. Proceed to

step 13A.

Note: You must have already initialized the module from Step 12.

13A. Tach Rate Learning

Note: Only use if the tachometer sensing method is chosen.

A. Connect the GREEN wire to the car’s tach wire under the hood.

B. Turn the On/Off control switch to the “OFF” position. Wait 5 seconds

for the first set of LED flashes to stop.

C. Push the White “option” button once and you will see the red LED

flash. Now push the middle button on the transmitter for a second

until you see the red LED flash again. You are now in TACH mode. (If

the LED flashed twice -- simply push the transmitter button again until

you get only one flash).

D. Wait 5 seconds for the red LED to flash 3 times.

E. Turn the On/Off control switch back to the “ON” position

F. Start the car and let it get to a normal idle. Do not press on the gas

pedal.

G. Push the red “code” button for a second.

H. Watch the red LED. It will turn on (solidly) after 3 or 4 seconds,

indicating that the idle rate has been learned.

I. Watch the LED stay on steady as the vehicle is running and goes off

as you rev the rpms above twice the idle rate. The LED must go out

when you rev it above twice the idle rate to confirm correct tach

learning.

J. Turn the key to the “Lock/Off” position.

K. Turn the On/Off control switch off and the LED will go out.

Note:

Once these steps are complete – you cannot use the LED to confirm

tach again. You can however repeat the above steps to learn tach over

again at any time.

14. Red/White –Remote Input Wire –Control Harness

The Red/White wire is used to trigger the remote starter to start the ve-

hicle. A negative pulse will trigger the remote starter to start the vehicle.

A second negative pulse will shut the remote starter down.

Connect this wire to the AUX output of the alarm system or keyless entry

system. If installing this remote starter on a vehicle and using the factory

keyless system to trigger the remote starter connect this Red/White wire

to either the lock or unlock wire. (Check this lock or unlock wire again

using the factory transmitter to check that the output is correct.) The

Red/White must “see” a negative trigger. If the trigger outputs are posi-

tive, a relay must be used to reverse the polarity. There is a double pulse

feature, option #8. Trigger the unit twice in 3 seconds and the remote

starter will start on the second pulse. See “Setting Program Features.”

To reverse a positive trigger to a negative trigger, connect the relay as

follows:

1. Positive trigger output to terminal 86 on the relay.

2. (-) Ground to terminal 85 on the relay.

3. (-) Ground to terminal 87 on the relay.

4. Red/White wire from remote starter to terminal 30 on the relay.

See the “HOW TO USE A RELAY” section at the end of the instructions.

15. Providing an IGN 3 output or a Clutch Bypass

any newer vehicles either have additional ignition circuits, alarm by-

pass units or the clutch needs to be triggered before the vehicle will

remotely start. By using additional relays, ignition circuits, alarm bypass

units and the clutch can be easily controlled. (The needed relays can be

easily purchased from DesignTech, Part # 20043 or Radio Shack, Cat #

275-226.)

Providing for a Clutch Bypass

Providing an Ignition 3 Output

Providing an Additional Ignition Circuit

OPTIONAL STEPS

16. Yellow/Green - Alarm Control - Control Harness

The Yellow/Green wire is specifically designed to control the Ignition In-

put of the remote control alarm system, which is triggering the remote

starter. Connect this Yellow/Green wire directly to the Ignition Input of

the alarm. This Yellow/Green wire will provide a positive 12-volt output

anytime it “sees” a positive 12-volt on the vehicle’s ignition #1 wire. This

output follows the Ignition #1 status. The only exception is that when the

remote starter is powering the vehicle, this wire will not activate. The

Ignition #1 (Blue)

From Remote Starter

Ground

To Additional

Ignition Circuits in

Vehicle

To Ignition #1 in Vehicle

Ground

Fused 12 volt Constant

(Tap into Large Pink Wire

From Battery)

Ignition #1 (Blue)

From Remote Starter

Ground

To Starter Side of

Clutch Switch

To Ignition #1 in Vehicle To Key Side of Clutch Switch

Ground

Ignition #1 (Blue)

From Remote Starter

Ground

Ignition #3 Output

(-) Negative

To Ignition #1 in Vehicle

Ground

22. Setting Program Features:

The remote starter unit has several special features available. You will

not need to use these special features in most situations. The factory

settings will operate most vehicles. You must turn the On/Off control switch

to the “OFF” position to program any features. Note that when turning off

this control switch, the red LED will flash a few times, giving the diagnostic

code described in Section 21. Wait a few seconds for it to finish before

programming your new Options.

Feature # Factory Setting (2 flashes) Option (1 flash)

1 “No-Tach” Tach ode

2 10 min. run time 15 min. run time

3 Normal Crank Extended Crank

4 Normal Crank Super Crank

5 Normal Voltage etering Ignore Voltage etering

6 Gasoline Vehicles Diesel Vehicles

7 “Enable” Feature No “Enable”

8 Normal Trigger Double Pulse Trigger

Option 1 “No-Tach” Tach Mode

Sets the starting method. The factory setting uses “No-Tach” starting. If

you wish to use the tach to start, follow the instructions in step #13.

Option 2 10 min. run time 15 min. run time

Gives you a choice of run times, either 10 or 15 minutes.

Option 3 Normal Crank Extended Crank

Will add 50% more cranking time to the “No-Tach” starting method.

Option 4 Normal Crank Super Crank

Adds 100% more cranking time to the “No-Tach” starting method. This

may be necessary on many diesels and hard to start vehicles.

Option 5 Normal Voltage Metering Ignore Volate Metering

Is used in the “No-Tach” starting method for some diesel vehicles or

vehicles that have poor electrical charging systems.

Option 6 Gasoline Vehicles Diesel Vehicles

This option is selected when installing into a diesel vehicle.

Option 7 “Enable” Feature No “Enable”

Cancels the Enable mode safety feature. The Enable mode requires

that the driver toggle the ON/OFF control switch “OFF” then “ON” in

order to “Enable” the vehicle to remotely start. This feature guards against

the accidental starting of the vehicle by the remote starter.

Option 8 Normal Trigger Double Pulse Trigger

Normal trigger will start and stop the remote starter with a single quick

ground pulse to the Remote Input wire. Double Pulse Trigger mode will

not activate the remote starter until it has seen two pulses within a 3-

second period of time. If the Remote Input wire is connected to the

door lock wire of the keyless entry module, you can lock the doors with

just one push of the transmitter’s lock button. If the transmitter’s lock

button is pushed again within 3 seconds, you will lock the doors AND

start the vehicle.

If you want the factory setting, DO NOTHING and skip this section. If you

want to change one of the features, TURN THE ON/OFF CONTROL SWITCH

TO THE “OFF” POSITION. Wait for the red LED to stop flashing, then con-

tinue with the following procedures:

A. For options 1-8: Push the white button to the left of the red LED. Each

time you push the button the red LED will flash 1 to 8 times signifying at

which feature you are (press it once, the LED flashes once. Press it

again and it will flash two times. Press it again and it will flash three

times, etc., to show what feature you are at).

B. When you are at the feature level you desire, push the Red button for

a second and the red LED will flash once to signify you are at the

Option setting. You can push the Red Option button again and it will

flash Twice to signify you are at the Factory setting. Push the Red

Option button again and you will go back to the Option setting.

C. You can choose to change another feature by starting over again at

Step A. or, in six seconds, the

remote starter

automatically exits the

programming mode (Three LED flashes).

D. When finished -- switch the Control Switch back ON. The LED will flash

once.

alarm remains operational during remote running because it is “blind” to

the fact that the vehicle is remotely running. This is a 300mA transistor

positive output.

17. Green/White - Sensor Loop IN - Control Harness

Gray/Black - Sensor Loop OUT - Control Harness

This Green/White wire is the input to a normally closed relay. When the

remote starter is running, this relay opens. If you have an external sensor,

like a shock sensor, pass the sense wire through this internal relay. When

the remote starter is running the vehicle, the relay is open and the alarm

does not “see” the input of the alarm sensor. When the vehicle is not

remotely running the alarm sensor works normally.

Cut the alarm sensor output wire in half. Connect one side of the cut

sensor wire to the Green/White wire and connect the other side of the

cut sensor wire to the Gray/Black wire.

18. Brown Wire - Accessory Pulse - Control Harness

The BROWN wire which is optional, is the Accessory Pulse output which

gives out a transistor ground output just as the Accessory wire comes on.

This is important in unusual vehicles to control the defroster or to control

the G R.A.P. system. Again, this is a 400 mA transistor ground output

which MUST drive a relay (not included).

19. Brown/White - Alarm Disable - Control Harness

The BROWN/WHITE wire which is optional is Alarm Disable, which will give

out a quick negative pulse just before starting the vehicle. This wire can be

used to turn off the factory alarm system in vehicles which have them. In

most vehicles this disarm wire is located in the driver’s kick panel.

REQUIRED FINAL STEPS

You must have hooked up all required wires and completed Initialization

(Step 12) to proceed forward.

20. Trying the Unit Out

WARNING: Be prepared to apply the brake during this testing. Close the

hood, fully apply the emergency brake. Turn the On/Off switch On, the

red LED will flash once.

A. Once all the wiring is checked and is correct put the vehicle in “park”,

the press the button on the transmitter of the host alarm or keyless

entry system, which controls the remote starter. Simply grounding

the Red/White wire will also trigger the remote starter to start.

B. The vehicle should start and continue to run for 10 minutes. Please

make sure that the engine shuts down if the vehicle is taken out of

“park”, the hood is opened of the brake is pressed.

21. Trouble Shooting with the Self Diagnostics

The remote starter contains a built in diagnostic routine that will indicate

why the unit started or why the unit turned off the car the last time that

the unit was used.

To activate the diagnostic mode for why it turned off, simply turn the On/

Off control switch to the “OFF” position. In a few seconds, the red LED on

the module will flash 1 to 12 times to identify the problem. See the chart

below for an explanation of the flashes:

1 flash 10/15 minute time out. Unit should be fine.

2 flashes Unit turned off because Brake or Hood was activated.

3 flashes No Tach sensing or Stalled. Review Step 13.

4 flashes Received another remote input door pin switch problem.

6 flashes Low battery voltage, or may be missing an ignition wire which

powers up the alternator

7 flashes Alarm Input triggered

8 flashes Over current - One of the 400 mA (-) transistor outputs of the

control harness is driving too much current. ake sure to use a

relay where necessary.

12 flashesThe Control Switch was turned off.

If you have any questions on the trouble shooting, see Step 10 of the

purple Trouble Shooting Guide.

23. Factory Anti-Theft Systems

any vehicles come with an anti-theft system that must be temporally

bypassed for the vehicle to be remotely started. Some systems use a

resistor in the key. Others use a transponder- a small device in the key

that communicates a high security code to the vehicle before the ve-

hicle will successfully start.

Check the following list of vehicles below. If your vehicle is listed, your

vehicle has an Anti-Theft System that the remote starter UST temporally

bypass in order to start the vehicle.

A Universal Alarm Bypass odule, model #20402, that will temporally

bypass the factory anti-theft systems when using the remote starter. Check

with your local retailer/installer to purchase this Universal Alarm Bypass

odule, model #20402.

List of vehicles and the types of security systems:

Acura 3.2TL 98+ Transponder

Acura CL 97+ Transponder

Acura RL 98+ Transponder

Acura Integra 2000 Transponder

Acura NSX Transponder

Audi A4, A6, A8 98+ Transponder

B W (all 97+) Transponder

Buick Century 97+ VATS

Buick LeSabre 90 – 96, 2000 VATS

Buick Park Ave 91 - 96 VATS

Buick Park Ave 97+ Transponder

Buick Regal 93 -96 VATS

Buick Riviera 93 -96 VATS

Buick Roadmaster 93 - 96 VATS

Buick Skylark 96 - 98 Passlock

Cadillac Allante VATS

Cadillac Brougham VATS

Cadillac Catera Transponder

Cadillac DeVille 92 - 96 VATS

Cadillac DeVille 99+ Transponder

Cadillac Eldorado 89 - 98 VATS

Cadillac Eldorado 99+ Passkey 3

Cadillac Escalade 99+ Passlock 2

Cadillac Fleetwood 90 - 96 VATS

Cadillac Seville 90 - 98 VATS

Cadillac Seville 99+ Passkey 3

Cadillac SLS/STS 97+ Passkey 3

Chevy Astro Van 98+ Passlock 2

Chevy Blazer 98+ Passlock 2

Chevy Camaro 86+ VATS

Chevy Cavalier 96-99 Passlock

Chevy Cavalier 2000 Passlock 2

Chevy Corvette 88+ VATS

Chevy Express 97+ Passlock 2

Chevy Impala 2000 Passkey 3

Chevy Lumina 96+ VATS

Chevy alibu 97+ Passlock 2

Chevy onte Carlo 96 - 99 VATS

Chevy onte Carlo 2000 Passlock 2

Chevy Pickup Full-size 98+ Passlock 2

Chevy S-10 98+ Passlock 2

Chevy Savanah Passlock 2

Chevy Suburban 98+ Passlock 2

Chevy Tahoe 98+ Passlock 2

Chevy Van 98+ Passlock 2

Chevy Venture 99+ Passkey 3

Chrysler Concorde 98+ Transponder

Chrysler LHS 99+ Transponder

Chrysler Sebring Conv 98+ Transponder

Dodge 300 99+ Transponder

Dodge Intrepid 98+ Transponder

Dodge Neon 2000 Transponder

Ford Contour 97 + P.A.T.S.

Ford Crown Vict. 98+ (opt’l) Transponder

Ford Excursion 2000 P.A.T.S.

Ford Expedition 97+ P.A.T.S.

Ford Explorer 98+ P.A.T.S.

Ford Focus 2000 Scurlock

Ford ustang 98+ P.A.T.S.

Ford Pickup (F150/F250) 98+ P.A.T.S.

Ford Ranger 99+ (optional) P.A.T.S.

Ford Taurus 96 + P.A.T.S.

Ford Windstar 2000 P.A.T.S.

G C Denali 99+ Passlock 2

G C Envoy 99+ Passlock 2

G C S-15 Jimmy 98+ Passlock 2

G C Safari 98+ Passlock 2

G C Sierra Pickup 98+ Passlock 2

G C Sonoma 98+ Passlock 2

G C Suburban 98+ Passlock 2

G C Yukon 98+ Passlock 2

G C Yukon XL 2000 Passlock 2

Honda Accord 98+ Transponder

Honda Odyssey 98+ Transponder

Honda Prelude 98+ Transponder

Honda S2000 Transponder

Infinity I30 98+ Transponder

Infinity Q45 98+ Transponder

Infinity QX4 Transponder

Jaguar (all 98+) Transponder

Jeep Grand Cherokee 99+ Transponder

Jeep TJ (Wrangler) 99+ Transponder

Lexus (all 97+) Transponder

Lincoln Continental 97+ P.A.T.S.

Lincoln LS 2000 P.A.T.S.

Lincoln ark V3 97+ P.A.T.S.

Lincoln Navigator 97+ P.A.T.S.

Lincoln Town Car 97+ P.A.T.S.

ercedes (all 97+) Transponder

ercury Cougar 99+ P.A.T.S.

ercury ountaineer 98+ P.A.T.S.

ercury ystique 97+ P.A.T.S.

ercury Sable 96+ P.A.T.S.

Nissan axima 98+ Transponder

Oldsmobile Achieva 95+ Passlock

Oldsmobile Alero 99+ Passlock 2

Oldsmobile Aurora VATS

Oldsmobile Bravada 98 Passlock 2

Oldsmobile Cutlass 97+ Passlock 2

Oldsmobile Eighty-Eight VATS

Oldsmobile Intrigue 98+ Passlock 2

Oldsmobile Ninety-Eight VATS

Oldsmobile Silhouette 99+ Passkey 3

Pontiac Bonneville 89+ VATS

Pontiac Firebird 88+ VATS

Pontiac Grand Am 96 - 98 Passlock

Pontiac Grand Am 99+ Passlock 2

Pontiac Grand Prix 92 – 96 VATS

Pontiac ontana 99 Passkey 3

Pontiac Sunfire 96-99 Passlock

Pontiac Sunfire 2000 Passlock 2

Porsche (most 97+) Transponder

Saab (all 97+) Transponder

Saturn 97+ Factory

Saturn 2000 Passkey 3

Toyota Avalon 98+ Transponder

Toyota Camry 98+ Transponder

Toyota Land Cruiser 98+ Transponder

Toyota Solara 99+ Transponder

Toyota Supra 98+ Transponder

Volkswagon Beetle 98+ Transponder

Volkswagon Golf 98+ Transponder

Volkswagon Passat 98+ Transponder

Volvo (all 98+) Transponder

From

Remote

Starter

To Vehicle's Accessory

+12 V

To Supply Ground (–) output

To Ground

To Vehicle's Accessory

+12 V

12 Volt Constant

From

Remote

Starter

12 Volt Constant

PLEASE HAVE MODEL NUMBER (28622) AND DIAGNOSTIC CODES

OF (STEP 21) READY BEFORE CALLING TECH SUPPORT

HOW TO USE A RELAY

any of the optional steps require a relay to be hooked up. The most

common relay used for this type application is the Bosch type relay (Ra-

dio Shack Cat.# 275-226). Use the diagram below for a typical hookup.

If you have another relay then you need to know that pins 85 and 86 in

this diagram relate to the coils of the relay. Pin 30 is the ‘common’, and

pin 87 is the ‘normally open’ contact. If your relay has a pin 87A in the

middle it is the normally closed contact and is not used.

Important Note:

ake sure that all drivers who will be operating the remote starter are

fully aware of the safety precautions installed and their limitations. Stress

the importance of switching the On/Off control switch to the “OFF” posi-

tion (down) every time the car is serviced. Give the user a copy of the

tan page - USER TIPS AND NOTES so that they can familiarize themselves

with the product.

USER INFORMATION: The tan USER TIPS AND NOTES sheet gives you further

detail regarding daily use of this product. Any modifications not expressly

approved will void the user’s authority to operate the equipment.

7 55 Cameron Brown Court; Springfield, Virginia 22153 USA

Tel: (703)866-2000 or (800)337-4468

www.designtech-intl.com

Table des matières

Autres manuels DesignTech Démarreur à distance

DesignTech

DesignTech AirWolf Manuel utilisateur

DesignTech

DesignTech AutoCommand 20022 Manuel utilisateur

DesignTech

DesignTech Ready start 24739 Manuel utilisateur

Manuels Démarreur à distance populaires d'autres marques

AstroStart

AstroStart 803U Manuel utilisateur

Durite

Durite 0-649-20 Manuel

EINHELL

EINHELL BT-PS 1000 Manuel

Linear

Linear ACCESS AK-21 Caractéristiques techniques

Soundstream

Soundstream TARANTULA RS.2 Manuel utilisateur

Jaycar Electronics

Jaycar Electronics MB3752 Manuel utilisateur

Ultra Start

Ultra Start 72 Series Manuel utilisateur

ADS

ADS FLASHLOGIC FLRSVW1 Manuel utilisateur

Selecta

Selecta JS012 Manuel utilisateur

Black Widow Security

Black Widow Security BW RAS 400 Manuel utilisateur

Vector

Vector Power City DK080706 Supplément

Code Alarm

Code Alarm CA-535 Manuel utilisateur

Ozito

Ozito OJS-800 Manuel utilisateur

Profi-Partner

Profi-Partner 46387 Manuel utilisateur

EZ STARTER

EZ STARTER EZ-45 Manuel utilisateur

Viper

Viper 4204 Manuel utilisateur

Essex Electronics

Essex Electronics KE-1701 Manuel utilisateur

EINHELL

EINHELL EGS 3600 Manuel

DesignTech secure start 28622 Manuel utilisateur

Manuels Démarreur à distance populaires d'autres marques