Desa CMA100F Manuel utilisateur

CMA100F, CMA102F, CMA200F, CMA204F, CMA205U,

CMA210W, GMC80FA, GMC81UA, and GMC82FA Wall

Mantel Kits

ASSEMBLY INSTRUCTIONS

IMPORTANT: Read entire instruction sheet before

assembling or installing mantel kit.

The CMA100 Series mantels are only approved for

use with CGCF, CGFP26E, VMH, and FMH series mod-

els. Do not use mantel with any other product.

The CMA200 and GMC80 Series mantels are approved

for use with any DESA Heating Products compact

ﬁreplace system. Do not use mantel with any other

product.

This mantel kit contains the following:

Description Part No.

• Mantel pieces (unassembled)

• Hardware kit 113166-17

• Black trim kit GAB6094

The hardware items needed from hardware kit*:

• 16 - 1 1⁄4" wood screws • 2 - Trim Plate

• 2 - 3" wood screws • 4 - Set Screws

• 8 - #8 x 3/4" particle board screws • 2 - Trim Shim

• 2 - Brackets

*Extra Hardware may be included.

Tools required:

• #2 Phillips power screw driver

• Slotted screw driver

If any of these pieces are missing or damaged, contact the dealer

where you purchased this mantel or DESA Heating Products at

1-866-672-6040 for referral information.

WARNING: Follow guidelines of paint or ﬁnish

manufacturer. Use care when ﬁnishing or painting

an unﬁnished mantel. Do not ﬁnish or paint mantel

pieces near running heater or open ﬂame. These

vapors are generally highly ﬂammable.

IMPORTANT: If you are staining an unﬁnished mantel, remove

any sawdust, dirt or oils. This will prevent blemishes from appear-

ing under the stain. Stain mantel before assembling according to

manufacturerʼs instructions. Apply sanding sealer.

IMPORTANT: If you are painting an unﬁnished mantel, assemble

the mantel before painting. Follow directions listed on the paint for

wood products. Apply base coat and top coat following directions

listed on product.

Note: Gather all mantel pieces together before assembling mantel.

WARNING: Only use 1 1/4" wood screws to as-

semble header and top. Damage to the mantel will

result if the longer screws provided are used for this

purpose.

Firebox

Perimeter

Trim Included

With This

Mantel

www.desatech.com

www.desatech.com 113146-01B

ASSEMBLING MANTEL

1. Some models require side/corner assembly. For these models,

lay leg side on ﬂoor. Position leg as shown in Figure 1. Align

predrilled screw holes in leg and leg side. Make sure ends are

ﬂush. Attach with two or three 1 1/4" wood screws, depending

on your model. Repeat for other leg.

2. For all models, place header between right and left legs. Make sure

header and legs are snug against each other (see Figure 2). The bot-

tom of header must be ﬂush with shoulder and sides of legs.

3. Position header mounting block as shown in Figure 3. Attach

mounting block through predrilled with two or four 1 1⁄4" wood

screws, depending on your model, as shown in Figure 3. Make

sure mounting block is secured to header and leg assembly.

(Mounting block may already be attached to header or leg as-

sembly, depending on your model.)

4. If your mantel has a heat reﬂector strip included in the kit, place

heat reﬂector strip against front of header and over both corner

sections. Make certain that heat reﬂector strip is ﬂush against

header and spacers are on bottom side. Attach with 1 1/4" wood

screws to each side as shown in Figure 4.

5. Turn top and leg assembly upside down. Place leg assembly

inside top (see Figure 5). The rear of legs should be ﬂush with

back of top and centered left to right. See Figure 6, page 3.

6. Place one metal bracket from hardware kit at the middle of

each leg assembly as shown in Figure 6, page 3. Make sure

brackets are ﬂush against leg assembly and top, then attach to

leg assemblies only with #8 x 3/4" particle board screws.

Figure 1 - Assembling Legs

Left Leg

Right Leg

Header

Figure 5 - Placing Mantel Assembly onto Mantel Top

Figure 3 - Attaching Header

Figure 2 - Installing Header

Note: Sides and header may

differ from illustration.

Note: Sides and

header may differ from

illustration.

Top

Leg

Assembly

Header

Top of

Mantel Figure 4 - Attaching Header

1 1⁄4" Wood Screw

Header

Heat

Reﬂector

Strip

Left Side

Leg Side

Leg

1 1⁄4" Wood

Screws

Left Side Leg

Assembly

Top View

Header

1 1⁄4" Wood Screw

Shoulder

Spacer

Mounting Block

Not All Models

www.desatech.com

113146-01B 3

ASSEMBLING TRIM

1. Remove packaging from three pieces of trim.

2. Locate two adjusting plates with set screws, and two shims in

the hardware packet.

3. Align shim under adjusting plate as shown in Figure 7.

4. Slide one end of adjusting plate/shim in slot on mitered edge

of top trim (see Figure 7).

5. Slide other end of adjusting plate/shim in slot on mitered edge

of side trim (see Figure 7).

6. While ﬁrmly holding edges of trim together, tighten both set

screws on the adjusting plate with slotted screwdriver.

7. Repeat steps 2 through 6 for other corner.

INSTALLING FIREPLACE WITH FULL

HEARTH BASE

1. Fireplace should be fully assembled. See Assembling Fireplace

in ﬁreplace ownerʼs manual,

2. Place mantel base next to wall at installation location. See

ﬁreplace ownerʼs manual for installation clearances.

3. Place ﬁreplace on wood mantel base and center left to right.

Turn mantel right side up, then slide mantel assembly over

heater (see Figure 8).

4. Firmly snap trim assembly on shoulder screws. Shoulder screws

are located on ﬁreplace cabinet (see Figure 8). (Locations may

vary with ﬁreplaces.)

5. Align ﬁreplace, base, and mantel so that the trim overlaps the

mantel evenly on all three sides.

6. Lower bottom louver door. Use two 3" wood screws provided

in hardware packet and attach ﬁreplace base to wooden base

(see Figure 9, page 4).

7. Make sure rear of legs are ﬂush with back of top, and mantel is

centered left to right inside top. Square legs evenly with sides

of mantel top, making certain gap between mantel top and

leg is the same from front to back. See Figure 6. Attach both

brackets to mantel top with #8 x 3/4" particle board screws.

Figure 7 - Assembling Trim

Side Trim

Slot

Top Trim

Mitered Edge

Shim

Set Screws

Adjusting

Plate

Slot

Figure 6 - Securing Top to Leg and Header Assembly

Metal

Brackets

Legs Should Be

Flush With Top

#8 x 3/4"

Particle Board

Screws

Small

Gap

Figure 8 - Fireplace, Trim Assembly, Mantel, and Mantel Base

Shoulder Screw

Assembled

Trim

Hole for 3" Wood Screw for Attaching

Fireplace to Wooden Base

Shoulder

Screws

Gas Line Ac-

cess Hole

Mantel Base

(Side view

for clarity)

Make certain

spacing is the

same front

and back.

113146-01

Rev. B

07/04

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

Technical Service and Parts: 1-866-672-6040

NOT A UPC

Figure 9 - Attaching Fireplace to Mantel and Mantel Base

Hole for 3" Wood Screw

for Attaching Fireplace to

Wooden Base

Bottom

Louver

Door

113146 01

7. Remove trim and mantel without disturbing the location of the

ﬁreplace/base assembly. Be careful not to damage wall, trim,

or mantel.

8. Install gas line. See Connecting To Gas Supply in ﬁreplace

ownerʼs manual.

9. Check for leaks. See Checking Gas Connections in ﬁreplace

ownerʼs manual.

10. Place mantel around ﬁreplace. Be careful not to damage wall

or mantel (see Figure 8, page 3).

11. Place trim kit on the shoulder screws located on the side and

top of the ﬁreplace. Firmly snap the trim over the shoulder

screws on ﬁreplace (see Figure 8, page 3).

12. Replace top louver onto ﬁreplace.

Ce manuel convient aux modèles suivants

Autres manuels Desa Cheminée intérieure

Desa

Desa Design Dynamics VTD-18P-PDG Guide de démarrage rapide

Desa

Desa Comfort Glow CGFB32C Guide de démarrage rapide

Desa

Desa Vanguard BHDV37NC Guide de démarrage rapide

Desa

Desa EFS33NRB Guide de démarrage rapide

Desa

Desa G8001 SERIES Manuel utilisateur

Desa

Desa VC36NE Series Guide de démarrage rapide

Desa

Desa VSGF36NRB Guide de démarrage rapide

Desa

Desa LGCFTP Guide de démarrage rapide

Desa

Desa B36L-MC Guide de démarrage rapide

Desa

Desa CGEF26B Instructions originales

Desa

Desa CD36RN Guide de démarrage rapide

Desa

Desa (V)CB36P(E) Manuel utilisateur

Desa

Desa S36 Series Manuel utilisateur

Desa

Desa E32L Guide de démarrage rapide

Desa

Desa P324E Guide de démarrage rapide

Desa

Desa KC36N SERIES Guide de démarrage rapide

Desa

Desa Variable Manually-Controlled Models Guide de démarrage rapide

Desa

Desa VDVF36PN/PP Guide de démarrage rapide

Desa

Desa IRONHAUS Yellowstone IDVF36SP Guide de démarrage rapide

Desa

Desa F48H Guide de démarrage rapide

Desa

Desa (V)GM36 Manuel utilisateur

Desa

Desa VVF36 Guide de démarrage rapide

Desa

Desa H) Guide de démarrage rapide

Desa

Desa Comfort Glow CGFP28P Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Miles Industries

Miles Industries Vogue 1300IRN Manuel