Desa Firewerks VTDMV18NA Guide de démarrage rapide

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-

lowed exactly, a ﬁre or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

— Installation and service must be performed by a quali-

ﬁed installer, service agency or the gas supplier.

VENTED DECORATIVE GAS LOG HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

VTDMV24NA, VTDMV24PA,

VTDMV18NA AND VTDMV18PA

www.desatech.com 114926-01B

WARNING: Improper installation, adjustment, altera-

tion, service or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualiﬁed installer, service

agency or the gas supplier.

WARNING: This appliance is for installation only in

a solid-fuel burning masonry or UL127 factory-built

ﬁreplace, constructed of noncombustible material and

connected to a working ﬂue. (See page 6 for minimum

ﬂue opening.

WARNING: This is a gas-ﬁred heater. It uses air (oxy-

gen) from the room in which it is installed. Provisions

for adequate combustion and ventilation air must be

provided. Refer to the National Fuel Gas Codes, ANSI

Z233.1/NFPA 54, Section 5.3, Air for Combustion and

Ventilation.

This appliance may be installed in an aftermarket,* per-

manently located, manufactured (mobile) home, where

not prohibited by local codes.

This appliance is only for use with the type of gas indi-

cated on the rating plate. This appliance is not convert-

ible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

State of Massachusetts: The installation must be made

by a licensed plumber or gas ﬁtter in the Commonwealth

of Massachusetts.

TABLE OF CONTENTS

Safety Information ............................................... 3

Local Codes ........................................................ 4

Product Identiﬁcation ........................................... 5

Unpacking ........................................................... 5

Product Features ................................................. 5

Installation ........................................................... 5

Operating Appliance .......................................... 10

Inspecting Burners .............................................11

Cleaning and Maintenance ................................ 12

Service Hints ..................................................... 12

Technical Service .............................................. 12

Replacement Parts ............................................ 12

Troubleshooting ................................................. 13

Speciﬁcations .................................................... 17

Accessories ....................................................... 17

Wiring Diagram .................................................. 17

Illustrated Parts Breakdown and Parts List ....... 18

Warranty Information ...........................Back Cover

www.desatech.com

114926-01B 3

SAFETY INFORMATION

WARNING: This product con-

tains and/or generates chemicals

known to the State of California

to cause cancer or birth defects

or other reproductive harm.

WARNING: Keep ﬂue open

when operating unit.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, operate

or service this log set. Improper use

of this log set can cause serious

injury or death from burns, ﬁre,

explosion, electrical shock and

carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the ﬂu, with head-

aches, dizziness or nausea. If you have these signs,

the log set may not be working properly. Get fresh

air at once! Have log set serviced. Some people

are more affected by carbon monoxide than others.

These include pregnant women, people with heart

or lung disease or anemia, those under the inﬂuence

of alcohol and those at high altitudes.

Natural & LP Gas: Natural & LP gas are odorless.

An odor-making agent is added to the gas. The

odor helps you detect a gas leak. However, the

odor added to the gas can fade. Gas may be present

even though no odor exists.

Make certain you read and understand all warnings.

Keep this manual for reference. It is your guide to

safe and proper operation of this log set.

WARNING: Do not place log

scraps or lava rocks on burner.

WARNING: Any change to

this log set or its controls can

be dangerous.

WARNING: Do not use a blow-

er insert, heat exchanger insert or

other accessory not approved for

use with this appliance.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

WARNING: Do not allow fans

to blow directly into the ﬁreplace.

Avoid any drafts that alter burner

ﬂame patterns.

WARNING: Installed decora-

tive glass door enclosures must

be fully opened when operating

this gas appliance.

Due to high temperatures, the

appliance should be located out

of trafﬁc and away from furniture

and draperies.

Do not place clothing or other

ﬂammable material on or near

the appliance. Never place any

objects on the heater.

Appliance assembly becomes

very hot when running. Keep

children and adults away from hot

surface to avoid burns or clothing

ignition. Appliance will remain hot

for a time after shutdown. Allow

surface to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with appliance.

You must operate this appliance

with a ﬁreplace screen in place.

Make sure ﬁreplace screen is

closed before running appliance.

www.desatech.com 114926-01B

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other ﬂam-

mable vapors and liquids.

Children and adults should be

alerted to the hazard of high tem-

perature and should stay away to

avoid burns or clothing ignition.

1. This appliance, as supplied, is only for use

with the type of gas indicated on the rating

plate. This appliance is not convertible for

use with other gases.

2. Do not place propane/LP supply tank(s) in-

side the structure. Locate propane/LP supply

tank(s) outdoors (propane/LP units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplierʼs

instructions

• if you cannot reach your gas supplier, call

the ﬁre department

4. Never install the log set

• in a recreational vehicle

• where curtains, furniture, clothing or other

ﬂammable objects are less than 42 inches

from the front, top or sides of the log set.

• in high trafﬁc areas

• in windy or drafty areas

5. Before installing in a solid fuel burning ﬁreplace,

the chimney ﬂue and ﬁrebox must be cleaned of

soot, creosote, ashes and loose paint by a qualiﬁed

chimney cleaner. Creosote will ignite if highly

heated. Inspect chimney ﬂue for damage. If dam-

aged, repair ﬂue before operating appliance.

6. You must operate this log set with ﬁreplace

screen in place and fully closed. Unless provided

by other means, screens shall have openings for

introduction of combustion air.

7. You must operate this log set with ﬁreplace screen

in place and fully closed. Unless provided by

other means, screens shall have openings for

introduction of combustion air.

8. To reduce the creation of soot, follow the instruc-

tions in Cleaning and Maintenance, page 12.

SAFETY INFORMATION

Continued

9. Do not use a blower insert, heat exchanger

insert or other accessory not approved for use

with this log set.

10. The installation and provisions for combustion

and ventilation air must conform with the Na-

tional Fuel Gas Codes, ANSI Z233.1/NFPA 54,

Section 5.3, Air for combustion and Ventilation.

11. Do not run heater

• where ﬂammable liquids or vapors are used

or stored

• under dusty conditions

12. Do not burn solid fuel in the ﬁreplace after

installing the log set. Do not use this log set

to cook food or burn paper or other objects.

13. Log set becomes very hot when in use. Keep

children and adults away from hot surface to

avoid burns or clothing ignition. Log set will

remain hot for a time after shutdown. Allow

surface to cool before touching.

14. Carefully supervise young children when they

are in the room with the log set.

15. Do not use heater if any part has been exposed

to or under water. Immediately call a qualiﬁed

service technician to inspect the room heater

and to replace any part of the control system and

any gas control which has been under water.

16. Turn log set off and let cool before servicing,

installing or repairing. Only a qualiﬁed service

person should install, service or repair log set.

17. Provide adequate clearances around air

openings.

LOCAL CODES

Install and use log set with care. Follow all local

codes. In the absence of local codes, use the lat-

est edition of the National Fuel Gas Code ANSI

Z223.1/NFPA 54*

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Battery march park

Quincy, MA 02269

www.desatech.com

114926-01B 5

PRODUCT

IDENTIFICATION

WARNING: Failure to posi-

tion the parts in accordance

with these diagrams or failure

to use only parts speciﬁcally

approved with this appliance

may result in property damage

or personal injury.

Figure 1 - Product Identiﬁcation

Log Set

Assembly

Piezo

Ignitor

Control

Knobs

Chassis

Assembly

Ember Pod

UNPACKING

CAUTION: Do not remove the

data plates from the grate as-

sembly. The data plates contain

important warranty and safety

information.

1. Remove log set assembly from carton.

IMPORTANT: Do not pick up assembly by

logs. This could damage the unit. Always

handle assembly by grate.

2. Remove all protective packaging applied to log

set for shipment.

3. Check all items for any shipping damage. If

damaged, promptly inform dealer where you

bought appliance.

PRODUCT FEATURES

This unitized gas log set is tested and approved to

ANSIZ21.60-2003 and CSA 2.2-2003 as a vented

decorative appliance.

This unit has a piezo ignitor. This system requires

no matches, batteries or other sources to light ap-

pliance.

INSTALLATION

WARNING: A qualiﬁed ser-

vice person must install heater.

Follow all local codes.

WARNING: Before installing

in a solid fuel burning ﬁreplace,

the chimney ﬂue and ﬁrebox

must be cleaned of soot, creo-

sote, ashes and loose paint by a

qualiﬁed chimney cleaner. Creo-

sote will ignite if highly heated. A

dirty chimney ﬂue may create and

distribute soot within the house.

Inspect chimney ﬂue for damage.

If damaged, repair ﬂue damper

before operating appliance.

CAUTION: This heater creates

warm air currents. These currents

move heat to wall surfaces next

to heater. Installing heater next

to vinyl or cloth wall coverings or

operating heater where impurities

(such as, but not limited to, to-

bacco smoke, aromatic candles,

cleaning ﬂuids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls or cause odors.

NOTICE: Installation, service and

repair of this appliance must be

performed by a qualiﬁed installer,

service agency, company or

gas supplier experienced with

this type of gas appliance. Only

factory authorized components

listed in these instructions may

be used in accordance with the

manufacturer's instructions and

all codes and requirements of

the authority having jurisdiction.

Any modiﬁcations to or use of

unauthorized components or

accessory items will void the

manufacturer’s warranty and may

result in a hazardous condition.

www.desatech.com 114926-01B

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP) for

your unit. If your gas supply is not correct, do not

instal in ﬁreplace. Call dealer where you bought

the appliance for proper type of appliance.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

INSTALLATION AND CLEARANCES

Figure 2 shows technical information regarding

the installation of your gas log set. Please make

sure all speciﬁcations shown are applicable before

installation is attempted.

LOG SIZING REQUIREMENTS

MINIMUM FIREBOX SIZE

LOG FRONT REAR* MIN. FLUE

SIZE HEIGHT DEPTH WIDTH WIDTH SIZE

18" 20" 14" 25" 20.5" 6.5"

24" 20" 14" 29" 24.5" 6.5"

*Measured at 14" depth

Figure 4 - Attaching Damper Clamp

Manufactured

Fireplace

Masonry

Fireplace

Damper

Clamp

Damper

Clamp Damper

VENTING SPECIFICATIONS FOR

INSTALLATION

The ﬁreplace chimney ﬂue and vent must be draft-

ing properly. To check the vent for proper drafting:

Light a tightly rolled newspaper on one end and

place it at the inside front edge of the ﬁreplace.

Observe the smoke and be sure the vent is properly

INSTALLATION

Continued

SPECIFICATIONS (W.C.)

FUEL INLET MANIFOLD

PRESSURE PRESSURE

Min. Max.

NG 7" 10.5" 3.5"

LP 11" 14" 10"

FLUE OPENING SPECIFICATIONS

Note: This vented appliance must be installed only

in a solid-fuel burning or UL127 factory-built ﬁre-

place constructed of noncombustible material and

connected to a working ﬂue. The ﬁreplace chimney

must have a permanent vent opening to outside

with minimum openings shown in Figure 3.

Figure 2 - Technical Information Chart

Figure 3 - Sizes and Clearances

drawing it up the chimney. If the smoke spills out

into the room, extinguish the ﬂame and remove any

obstruction until proper venting is achieved.

The chimney ﬂue damper must be ﬁxed open to pro-

vide a minimum of 32 square inch of free air opening

at all times during operation of the log set. A damper

clamp is included to secure the damper.

The minimum ﬂue sizes shown in Figure 3 are

based on a 6' chimney height using round pipe. Your

minimum ﬂue size will vary based on input rate and

chimney height. Refer to the National Fuel Gas Code

ANSI Z223.1/NFPA 54, Section 6.6 for details.

INSTALLING DAMPER CLAMP

Secure the damper stop clam to the edge of the

damper as shown in Figure 4. If for any reason

this clamp doesn't work on your ﬁreplace, another

suitable clamp or permanent stop must be installed,

or the damper blade must be cut or removed.

Valve Bracket

INSTALLING REMOTE CONTROL

ACCESSORY BRACKET

If installing optional remote control accessory you

will need to install the remote accessory bracket

for the receiver.

Use screws provided to attach bracket to valve

bracket as shown in Figure 5.

Follow installation instructions included with

remote accessory.

Figure 5 - Attaching Remote Bracket to

Valve Bracket

Remote

Bracket

www.desatech.com

114926-01B 7

INSTALLING APPLIANCE

WARNING: Special care is

required if you are installing the

unit into a sunken ﬁreplace. You

must raise the ﬁreplace ﬂoor to

allow access to gas log controls.

This will insure adequate air

ﬂow and guard against sooting.

Raise the ﬁreplace ﬂoor using

noncombustible material.

CAUTION: Do not pick up ap-

pliance assembly by logs. This

could damage unit. Only handle

assembly by grate.

IMPORTANT: Make sure appliance is level. If

unit is not level it will not work properly.

Center the appliance in the ﬁreplace. Make certain

the grate front feet sit inside the front edge of

the ﬁreplace and that there is adequate clearance

around the appliance for access and operation.

Note: The installation of appliances designed for

manufactured home (U.S. only) or mobile home

installation must conform with the standard CAN/

CSA Z240, Mobile Housing, in Canada, or with

the Manufactured Home Construction and Safety

Standard, Title 24 CFR, Part 3280, in the United

States, or when such a standard is not applicable,

ANSI/NCSBCSA225.1/NFPA501A, Manufactured

Home Installations Standard.

CONNECTING TO GAS SUPPLY

WARNING: A qualiﬁed service

person must connect heater to gas

supply. Follow all local codes.

WARNING: This appliance

requires a 3/8" NPT (National Pipe

Thread) inlet connection to the

control valve.

INSTALLATION

Continued CAUTION: Never connect

propane/LP unit directly to the

propane/LP supply. This unit re-

quires an external regulator (not

supplied). Install the external

regulator between the unit and

the propane/LP supply.

WARNING: Never connect

natural gas ﬁreplace to private

(non-utility) gas wells. This

gas is commonly known as

wellhead gas.

Installation Items Needed

Before installing heater, make sure you have the

items listed below.

• approved ﬂexible gas hose and ﬁttings (supplied

with appliance -if allowed by local codes)

• external regulator (propane/LP models only)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve*

• test gauge connection*

• sediment trap

• tee joint

• pipe wrench

* A CSA design-certiﬁed equipment shutoff valve

with 1/8" NPT tap is an acceptable alternative to

test gauge connection. Purchase the optional CSA

design-certiﬁed equipment shutoff valve from your

dealer. See Accessories, page 17.

For propane/LP units, the installer must supply an

external regulator. The external regulator will reduce

incoming gas pressure. You must reduce incoming gas

pressure to between 11 and 14 inches of water. If you

do not reduce incoming gas pressure, control valve

damage could occur. Install external regulator with the

vent pointing down as shown in Figure 6. Pointing the

vent down protects it from freezing rain or sleet.

Propane/LP

Supply Tank External

Regulator

Vent

Pointing

Down

Figure 6 - External Regulator with Vent

Pointing Down

www.desatech.com 114926-01B

INSTALLATION

Continued

CAUTION: Use only new, black

iron or steel pipe. Internally-tinned

copper tubing may be used in

certain areas. Check your local

codes. Use pipe of 1/2" diameter

or greater to allow proper gas vol-

ume to heater. If pipe is too small,

undue loss of volume will occur.

Installation must include an equipment shutoff

valve, union and plugged 1/8" NPT tap. Locate NPT

tap within reach for test gauge hook up. NPT tap

must be upstream from log set (see Figure 7).

IMPORTANT: Install equipment shutoff valve in an

accessible location. The equipment shutoff valve is for

turning on or shutting off the gas to the appliance.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could result

in clogged heater valves.

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

We recommend that you install a sediment trap in

supply line as shown in Figure 7. Locate sediment

trap where it is within reach for cleaning. Install in

piping system between fuel supply and appliance.

Figure 7 - Gas Connection

* Purchase the optional CSA design-certiﬁed shutoff

valve from your dealer. See Accessories, page 17.

** Minimum inlet pressure for purpose of input

adjustment.

Approved Flexible

Gas Hose (If

allowed by local

codes)

CSA Design-Certiﬁed

Equipment Shutoff

Valve with 1/8" NPT

Tap*

Natural

From Gas

Meter (5" W.C.**

to 10.5" W.C.

Pressure)

Propane/LP

From External

Regulator (11"

W.C.** to 14"

W.C. Pressure)

3" Min.

Pipe Cap Tee

Nipple Joint

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections for leaks after

installing or servicing. Correct

all leaks at once.

WARNING: Never use an open

ﬂame to check for a leak. Apply a

noncorrosive leak detection ﬂuid

to all joints. Bubbles forming show

a leak. Correct all leaks at once.

CAUTION: Make sure exter-

nal regulator has been installed

between propane/LP supply

and appliance. See guidelines

under Connecting to Gas Sup-

ply, page 7.

PRESSURE TESTING GAS SUPPLY

PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

1. Disconnect appliance with its appliance main

gas valve (control valve) and equipment shutoff

valve from gas supply piping system. Pressures

in excess of 1/2 psig will damage control valve.

2. Cap off open end of gas pipe where equipment

shutoff valve was connected.

3. Pressurize supply piping system by either

opening propane/LP supply tank valve for

propane/LP gas or opening main gas valve

located on or near gas meter for natural gas

or using compressed air.

4. Check all joints of gas supply piping system.

Apply noncorrosive leak detection ﬂuid to all

joints. Bubbles forming show a leak.

5. Correct all leaks at once.

Locate sediment trap where trapped matter is not

likely to freeze. A sediment trap traps moisture and

contaminants. This keeps them from going into

heater controls. If sediment trap is not installed or

is installed wrong, heater may not run properly.

CAUTION: Avoid damage to

gas control. Hold gas control

with wrench when connecting it

to gas piping and/or ﬁttings.

Sedament Trap

www.desatech.com

114926-01B 9

INSTALLATION

Continued

Figure 8 - Equipment Shutoff Valve

Equipment

Shutoff

Valve

Open

Closed

Figure 10 - Checking Gas Joints

(Natural Gas Only)

Control Valve

Location

Equipment

Shutoff Valve

Propane/LP

Supply Tank

Equipment

Shutoff Valve

Gas Meter

Figure 9 - Checking Gas Joints

(Propane/LP Gas Only)

Control Valve

Location

6. Reconnect heater and equipment shutoff

valve to gas supply. Check reconnected ﬁt-

tings for leaks.

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 8).

2. Pressurize supply piping system by either

opening propane/LP supply tank valve for

propane/LP gas or opening main gas valve

located on or near gas meter for natural gas

or using compressed air.

3. Check all joints from gas meter to equipment

shutoff valve for natural gas or propane/LP supply

to equipment shutoff valve for propane/LP (see

Figure 9 or 10). Apply noncorrosive leak detection

ﬂuid to all joints. Bubbles forming show a leak.

4. Correct all leaks at once.

Pressure Testing Appliance Gas

Connections

1. Open equipment shutoff valve (see Figure 8).

2. Open main gas valve located on or near gas

meter for natural gas or open propane/LP

supply tank valve.

3. Make sure control knob of appliance is in the

OFF position.

4. Check all joints from equipment shutoff valve

to gas control (see Figure 9 or 10). Apply

noncorrosive leak detection ﬂuid to all joints.

Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light appliance (see Operating Appliance,

page 10) Check all other internal joints for

leaks.

7. Turn off appliance.

PLACEMENT OF LOOSE EMBERS

CAUTION: Do not place

any loose embers around pilot

assembly.

Two bags of loose embers are provided with this

unit. For this installation use the embers that are

approximately 1" square in size. If needed, larger

embers can be broken to size. These embers aid

in concealing the burner pan, directing ﬂames

through the ember bed, quiet operation of the unit

and gives a natural random ﬂame pattern.

Place embers as follows:

1. Place embers around the center ember bed or

ember pod.

2. Place individual embers on their edge (not ﬂat)

along the top of the burner pan. This aids in

directing ﬂames from the burner through the

ember bed.

Note: Too many embers or embers placed ﬂat

along burner pan can suppress the ﬂames.

3. When unit is lit, check ﬂames for random appear-

ance and ember bed glowing red-orange in color

(see Burner Flame Pattern, page 11). If this is

not happening, either add, remove or reposition

loose embers. IMPORTANT: Turn unit off and

let cool before repositioning loose embers.

Figure 11 - Placement of Embers

www.desatech.com 114926-01B

5. Wait ﬁve (5) minutes to clear out any gas.

If you then smell gas, STOP! Follow "B" in

the safety information in column 1. If you

don't smell gas, go on the next step.

6. Press in and turn control knob counter-

clockwise to the PILOT position.

Press in control knob for ﬁve (5) seconds

(see Figure 12).

7. With control knob pressed in, press and release

ignitor button. This will light pilot. If needed,

keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a

qualiﬁed service person or gas supplier for

repairs.

8. Keep control knob pressed in for 30 seconds

after lighting pilot. After 30 seconds, release

control knob.

• If control knob does not pop out when

released, contact a qualiﬁed service person

or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4

through 8.

9. Slightly push in and turn control knob coun-

terclockwise to the ON position.

10. Wait one minute and move switch to the

ON position to light burner. Note: AUTO is

only functional when using optional remote

control accessory.

11. Set ﬂame adjustment knob to any level

between HI and LO.

Figure 12 - Setting Control Knobs

Piezo Ignitor

Control

Knob

Flame Adjustment Knob

TO TURN OFF GAS

TO APPLIANCE

1. Push switch into OFF position. The pilot

will remain lit for normal service.

2. Access control knobs.

3. Depress gas control knob slightly and turn

clockwise to OFF. Do not force.

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: Remote control accessory must be pur-

chased separately (see Accessories, page 17).

Follow instructions included with the remote

control.

OPERATING APPLIANCE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: Keep ﬂue open

when operating unit.

WARNING: If you do not fol-

low these instructions exactly,

a ﬁre or explosion may result

causing property damage, per-

sonal injury or loss of life.

A. This appliance has a pilot which must be

lighted with a piezo ignitor. When lightning

the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell next

to the ﬂoor because some gas is heavier than

air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not

use any phone in your building.

• Immediately call your gas supplier from

a neighborʼs phone. Follow the gas

supplierʼs instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

C. Use only your hand to push in or turn gas

control knob. Never use tools. If the knob

will not push in or turn by hand, do not try

to repair it, call a qualiﬁed technician. Force

or attempted repair may result in a ﬁre.

D. Do not use this appliance if any part has been

under water. Immediately call a qualiﬁed

service technician to inspect the appliance and

to replace any part of the control system and

any gas control which has been under water.

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information,

above.

2. Make sure switch is in OFF position.

3. Be sure gas line shut-off valve is OPEN.

4. Press in and turn control knob clockwise

to the OFF position (see Figure 12).

Note: Knob cannot be turned from PILOT

to OFF unless knob is pushed in slightly. DO

NOT FORCE.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Desa Chauffage au gaz

Desa

Desa Comfort Glow CGP10 Guide de démarrage rapide

Desa

Desa Comfort Glow CG10P Guide de démarrage rapide

Desa

Desa BCLP375 Manuel utilisateur

Desa

Desa LSFG20NT Instructions originales

Desa

Desa VDL18PR Guide de démarrage rapide

Desa

Desa Comfort Glow CGB3924PR Guide de démarrage rapide

Desa

Desa ROPANE CONSTRUCTION HEATER Manuel utilisateur

Desa

Desa GN30A Instructions originales

Desa

Desa CDR3924PT Guide de démarrage rapide

Desa

Desa Comfort Glow RFN30TA Guide de démarrage rapide

Desa

Desa Comfort Glow CGB3924NR Guide de démarrage rapide

Desa

Desa VUL24ND Guide de démarrage rapide

Desa

Desa 24" Variably-Controlled Models Guide de démarrage rapide

Desa

Desa Comfort Glow CGG3324N Guide de démarrage rapide

Desa

Desa TC100R Manuel utilisateur

Desa

Desa FLAME-MAX FVFM27PR Guide de démarrage rapide

Desa

Desa CGP18C Guide de démarrage rapide

Desa

Desa Flame-Max VYM27PR Guide de démarrage rapide

Desa

Desa SGS3124P Guide de démarrage rapide

Desa

Desa RCLP375B Manuel utilisateur

Desa

Desa CFN2800BTB Guide de démarrage rapide

Desa

Desa Vanguard VVTR18 Guide de démarrage rapide

Desa

Desa Vanguard VN600BA Guide de démarrage rapide

Desa

Desa Comfort Glow SYCAMORE SPLIT SMS18 Guide de démarrage rapide

Manuels Chauffage au gaz populaires d'autres marques

Superior

Superior BGE18NV Manuel utilisateur

Dru

Dru Room-sealed atmospheric gas-fired heating... Manuel utilisateur

klover

klover TKR 35 Manuel utilisateur

Rothenberger Industrial

Rothenberger Industrial 035984 Manuel utilisateur

New Buck Corporation

New Buck Corporation 34 Manuel utilisateur

Hargrove

Hargrove Timberland Glow Guide de démarrage rapide

Kinder

Kinder Cameo BF Manuel utilisateur

Qlima

Qlima GH 438 B-2 Manuel

Gasmate

Gasmate AH100 Series Manuel utilisateur

Medallion

Medallion MBP20TLB Guide de démarrage rapide

Clarke

Clarke DEVIL 910SS Manuel utilisateur

Superior

Superior BGE18NR Manuel utilisateur

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Instructions d'installation

L.B. White

L.B. White Therma Grow HW220 Manuel

Sealey

Sealey LP35.V5 Manuel utilisateur

Italkero

Italkero Falo Evo Manuel utilisateur

Williams

Williams 2509822A Manuel utilisateur

Romotop

Romotop Heckla 1301 Caractéristiques techniques