Deponti Pinela Manuel utilisateur
User manual / Assembly instructions
Louvered Pergola
Type Pinela
Version: EN – September 2020
Contents
1. Introduction
2. Safety precautions and warnings
3. Product description
4. Parts overview
1. Terminology
2. Hardware details
3. Exploded view
4. Delivery Inspection
5. Preparation for assembly
1. Conditions for assembly
2. Inspection of tools and accessories
6. Assembly
1. Mounting the wall profile (in case of wall installation)
2. Pillar and integrated gutter connection
3. Panel installation
4. Perimeter lightning installation
7. Programming instructions
1. Remote control
2. Programming
8. FAQ
9. Maintenance
10. Disposal of waste
11. Warranty conditions
12. Contact
3
3
5
6
6
7
9
10
11
11
12
13
13
15
17
20
23
23
24
26
26
26
27
27
ti
KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE USE!
For the duration and the terms and conditions of the warranty we recommend that you contact your supplier. We
also refer you to our General Terms and Conditions of Sale and Delivery which are available on request. Depon
B.V. accepts no liability for any damage or injury resulting from a failure to carefully follow the instructions in this
manual or exercise due caution during transport, assembly, use and maintenance of the pergola. As a result of
our policy of continuous product improvement, certain product details may differ from what is described in this
manual. For this reason the instructions provided only serve as a guideline for installation of the product this
manual describes. This manual has been compiled with the utmost care, but Deponti B.V. cannot be held
responsible for any errors in this manual or the consequences thereof. Furthermore, all rights are reserved and no
part of this manual may be reproduced in any way whatsoever.
page
2
LEES
AANDACHTIG
!
1. Introduction
2. Safety precautions and warnings
Important:
Please read the safety precautions and warnings before assembling the pergola.
During assembly, carefully follow the instructions and guidelines as described in this manual.
Never change the order of the steps to be performed. If any aspect of the assembly
procedure is unclear, please contact your Acrylshop24 partner. We reserve the right to make
technical changes without written notice.
We normally recommend that the pergola must be assembled by at least two
people (qualified technicians/authorized installers) working together.
Check the delivery immediately upon receipt. In the event of damage or an incomplete
delivery please contact your partner immediately.
The materials must be stored in a dry, ventilated area, not exposed to direct sunlight.
Open the packaging carefully. Make sure that you do not damage the product.
To prevent damage to your pergola, place the parts on a smooth, clean surface. Place the
profiles on a flat surface, protected from sun and rain.
Congratulations on the purchase of your Acrylshop24 pergola!
Before you can start enjoying your pergola it must be assembled properly. This manual provides clear
instructions for all the steps you must complete for correct assembly of your Acrylshop24 pergola. We
recommend that you take the time to read the entire manual before you begin the assembly.
Check whether you have received all the necessary parts before you begin assembly. For your safety,
follow all the applicable instructions. This also guarantees the safety of the installed roof. If you
should have any questions, please feel free to contact your Acrylshop24 partner.
!
READ
CAREFULLY
This manual should be kept in a safe, dry and shady place. In the event of damage or loss, the user
must request a new copy of the manual from the dealer.
page
3
2. Safety precautions and warnings (continued)
Adding or removing parts, the use or installation of materials. other than described in this
manual, may adversely affect the safety of the pergola and is therefore strongly discouraged!
Pay attention and be aware of moving parts. Make sure that all power supply is cut off during
the assembly.
Cordon off the assembly location so that others are kept at a distance.
Always wear the correct protective clothing (work gloves, dust mask, safety glasses, shoes
with non-slip soles, etc.) during installation or servicing.
Mount the system against a firm, flat wall and on a flat and stable foundation. Ensure that
the wall and the ground are clean and dry.
Never step or walk on the panelsystem.
You must maintain and clean your pergola at least once a year. During this yearly
maintenance make sure all fasteners are properly tightened.
Dispose the product in accordance with local laws and regulations.
It is forbidden to tamper with the bioclimatic pergola system.
When safety regulations and instructions are not followed correctly, Acrylshop24 will not
accept responsibility for damage(s) and injuries.
page
4
3. Product description
page
5
The Pinela roof is a bioclimatic pergola system which is a rotatable panel system. The Pinela panels
can rotate 120⁰ degree. Also it protects from sun, rain and limited snow loads. The panels are
connected to a linear actuator and are operated with the remote control by the motor.
The Pinela is available in the following dimensions;
Width (mm):
Projection (mm):
3000 / 3500
3011 / 3539* / 4067 / 4947 * only by 3500 mm width!
NOTE: All pillars have a length/height of 350cm and don’t have a foot/base plate.
When assembled as a freestanding pergola with additional mounting bracket, the maximum gutter
height is 250cm. The extra length of the pillar is to prevent collapsing.
Optional additions:
Perimeter lighting system
Mounting bracket for pillars
Wind resistance:
No of
Panel
Projection (cm) Projection (cm) Width (cm)
(Freestanding) (Wall installation) 300 350
16 301.1 303.9 7 7
19 353.9 356.7 7 7
22 406.7 409.5 7 7
27 494.7 497.5 7 7
The values given are according to the Beaufort scale ( 7 Beaufort = 13.9 – 17.1 m/s ≤ 0.18
kN/m2).
Calculated for the Pinela with a front height of 250 cm according to Eurocode EN 1991-1-4
Terrain Category 4.
Snow load (kg/m2):
No of
Panel
Projection (cm) Projection
(cm) Width (cm)
(Freestanding) (Wall
installation) 300 350
16 301.1 303.9 125.3 119.0
19 353.9 356.7 103.3 98.0
22 406.7 409.5 81.4 77.0
27 494.7 497.5 44.8 42.0
4. Parts Overview
4.1 Terminology
Linear Actuator
Linear Actuator provides the movement of the bioclimatic pergola pannels. The linear actuator is
located on the lateral Integrated gutter. The linear actuator has to be adjust to exact movement. This
must be done during to installation.
The linear actuators works with 24V power. The control box provids power for the linear actuator.
The control box works with 230V. The control box is located on rear Integrated gutter. (see below)
page
6
2. Hardware details
Freestanding model:
Integrated gutter – Pillar connection:
a. M8 nut stainless steel
b. Washer for M8x60
c. M6 nut stainless steel
d. Washer for M6x45
Wall installation
Wall bracket – Integrated Gutter connection:
NOTE: Wall mounting hardware not included. Choose the correct hardware for your installation
situation
a.
b.
M8x25mm bolt
M4.8x25mm self-drilling screw
page
7
Linear Actuator – Linear Actuator Connector:
a. 16mm Segment
Linear Actuator Connector– 40x20mm Profile connection:
a.
b.
c.
M10x50 hexagonal bolt stainless steel
M10 washer stainless steel
M10 nut stainless steel
40x20mm Profile – Panel Connection:
a. 8mm Segment
page
8
4.3 Exploded view
Exploded view integrated Gutter
Exploded view panels
BOMID Description QTY BOMID Description QTY
1 M8x60 stay bolt 6 6 Integrated gutter for Pinela 1
2 Sealed Nut M8 stainless steel 6 7 Insulation cover - left 1
3 Washer M8 stainless steel 6 8 M6x40 stay bolt 2
4 Insulation cover - right 1 9 Nut (M6) 2
5 Washer M6 2
BOMID Description QTY BOMID Description QTY
1 Power pin 2 5 Panel profile for Pinela 1
2 Side cover cap 2 6 Top Gasket 1
3 Side cover cap screw 4
4 Fixed pin 2
page
9
Exploded view Pillar
Two module connector
4.4 Delivery Inspection
Always carefully check the delivered items against the accompanying delivery note to ensure that the
quantity and quality are correct. Any visible defects must be reported in writing within 7 days of
delivery.
Note:
Boxes with red label: Electronic parts like Control Unit Box. Remote Controls.
Boxes with blue label: Metal parts like U Brackets. Mounting brackets. Pillar caps.
page
10
Table des matières
Autres manuels Deponti Accessoires
