DentalEZ Forest Manuel utilisateur

INSTALLATION

INSTRUCTIONS

2.17.21 0097-305 Rev. T 4 of 4

6200 NE Cherry Drive, Hillsboro, OR 97124 USA (TF) 800 . 423 . 3555 (T) 503 . 640 . 3012 (F) 503 . 693 . 9715

DTE OREGON, INC. DENTALEZ.COM

REAR PIVOT MOUNT

1 of 4

ALERT SYMBOL KEY

The safety notices associated with the following should be

given special attention when they appear in maintenance,

operating and emergency procedures in the guide.

WARNING indicates that the personal safety of the

patient, end user or technician could be compromised

by disregarding the WARNING. Not following instruc-

tions may result in an injury.

CAUTION indicates that a particular procedure

or precaution must be followed to avoid system

irregularity or possible damage to the product.

NOTE indicates special information to improve the

ease of maintaining the product, or to clarify important

information.

CAUTION: To avoid electrostatic discharge (ESD)

damage to electronics, always wear grounded wrist

strap attached to a ground adapter (eg: Banana or

Grounding plug) when handling circuit boards, chair

controls, and cables or working in the area of electrical

circuits.

CAUTION: Field modiﬁcations that alter the electrical

and/or mechanical safety of Forest products conﬂict

with agency construction ﬁle requirements and are not

sanctioned by Forest.

NOTE: Installation Veriﬁcation: Refer to Operator’s

Guide or Service Manual on our website at Forest-

dental.com; perform all operations. If operations

performing as intended installation complete. If

operations not performing as intended, review steps in

installation instructions to conﬁrm correct installation or

call Forest Technical Support at 800-423-3555.

FIG.1: POSITION CHAIR

Tools Required: 1/8”, 5/32”, 3/16”, 3/32” & 5/16”, 3mm, 8mm, and

10mm, Allen Hex Wrenches, 1/8”, 5/16” Allen Sockets with

Torque Wrench, 3/4”, 9/16” & 15/16” Wrench, Flathead Screw-

driver, and Nitrile Gloves.

NOTE: Chairs purchased before July of 2014 contain

metric screws, all chairs purchased after this date

contain standard screws. This kit contains a metric and

standard nut and bolt set to accommodate either chair.

Please check to make sure that you are using the

correct tools and hardware for your chair before

proceeding.

NOTE: If rear pivot is already installed, proceed to page 3.

REAR PIVOT ASSISTANT’S OR CUSPIDOR

MOUNT 3900 CHAIR

STEP 1: Position the chair’s back in the fully up position and

the base in the fully down position. (FIG. 1)

STEP 2: Remove the 6 screws holding the upholstery in place

(Phillips screwdriver). Sit upholstery and hardware aside.

(FIG. 2)

FIG. 2: REMOVE SEAT UPHOLSTERY

ROUTING DRAIN/SUCTION LINE

STEP 1: Remove covers. (FIG. 1)

STEP 2: Route and secure tubings together with zip tie. (FIG. 2)

CAUTION: Do not kink tubings with zip tie.

STEP 3: Make appropriate connection at utility center.

STEP 4: Reinstall covers.

STEP 5: Reinstall upholstery if originally removed.

FIG. 1: REMOVE COVERS.

COVERS

DRAIN LINE FROM

REAR PIVOT UNIT

ZIP TIE

TUBINGS

TOGETHER

FIG. 2: REAR UNIT DRAIN/SUCTION LINE.

2 of 4 3 of 4

REAR PIVOT ASSISTANT’S OR CUSPIDOR

MOUNT 3900 CHAIR (CONTINUED)

LIFT COVER PLATE INSTALLATION (FIG. 3)

STEP 1: Remove existing lift cover plate from chair (1/8” or

3mm hex).

STEP 2: Use pre-existing screws to install the new cover plate

that contains the umbilical routing hole.

REAR PIVOT MOUNT SETUP (FIG. 4)

STEP 1: Install rear pivot bumpers on the mounting plate using

the screws provided (5/32” hex). Choose hole location based

on the desired limits of the link arm that will be attached.

REAR PIVOT MOUNT INSTALLATION (FIG. 5)

STEP 1: Remove 3 shoulder bolts as shown (3/8” or 10mm hex)

If a chair mounted touchpad is installed, remove it during this

step.

STEP 2: Install mounting plate and spacers with nuts and

bolts provided. (5/16” hex & 3/4” socket or 8mm hex & 19mm

socket). If re/installing a chair mounted touchpad, insert the

touchpad mount assembly in place of the provided spacer.

STEP 3: Remove remaining shoulder bolt. Insert spacer and

secure with nut and bolt (5/16” hex & 3/4” socket or 8mm hex

& 19mm socket).

FIG. 3:

STEP 1: REMOVE

BOLTS (3)

STEP 2: INSTALL SPACERS/BOLTS

(3)

REAR PIVOT BEARING ASSEMBLY - ASSISTANT’S

1090/1091/1095/1096/1290

REAR PIVOT BEARING ASSEMBLY - CUSPIDOR OR DUO CONTROL

1490/1495PI/1500PI/1580/1590/1591

CAUTION: Protect work area. Threads to be

sealed must be clean and dry. Shake the product

applicator before use.

FIG. 4:

FIG. 5:

CAUTION: Protect work area. Threads to be sealed

must be clean and dry. Shake the product applicator

before use.

(REAR ADAPTER)

MAIN BEARINGS

1115-314

GREASE

BEARINGS

(LINK 1110-625)

LOCTITE®

(243/242) P/N:

0030-010

(ARM SIDE )

INTERMEDIATE BEARINGS

0010-679

MODEL 3900

CHAIR

ASSISTANT’S UNIT

(LINK = 1110-911)

(REAR ADAPTER)

MAIN BEARINGS

1115-314

MODEL 3900

CHAIR

GREASE

BEARINGS

LOCTITE®

(243/242) P/N:

0030-010

(ARM SIDE )

INTERMEDIATE BEARINGS

0010-728

CAUTION: 2 or 3 screw threads from bolt (1) should

protrude below the nut (13) for proper installation.

CAUTION: 2 or 3 screw threads from bolt (1) should

protrude below the nut (13) for proper installation.

STEP 3: REMOVE BOLT; INSTALL

SPACER/BOLT (1) CUSPIDOR OR

DUO CONTROL

LOCTITE®

(243/242) P/N:

0030-010

Autres manuels DentalEZ Équipement dentaire

DentalEZ

DentalEZ Heritage Simplicity LED Light Manuel utilisateur

DentalEZ

DentalEZ aXcs Magellan Manuel utilisateur

DentalEZ

DentalEZ StarDental 430 SWL Flex Manuel utilisateur

DentalEZ

DentalEZ TruSim Manuel utilisateur

DentalEZ

DentalEZ Aeras Ramvac C3 Manuel utilisateur

DentalEZ

DentalEZ AERAS Star Manuel utilisateur

DentalEZ

DentalEZ Star Titan Low-Speed Manuel utilisateur

DentalEZ

DentalEZ Aeras 400 Flex Manuel utilisateur

DentalEZ

DentalEZ Simplicity LED Light Head Manuel

DentalEZ

DentalEZ Star TITAN 3 Manuel utilisateur

DentalEZ

DentalEZ Forest Manuel utilisateur

DentalEZ

DentalEZ J-Chair J-3 Manuel utilisateur

DentalEZ

DentalEZ StarDental 430 SWL Torque Manuel utilisateur

DentalEZ

DentalEZ Star LUBRICATED PROPHY ANGLE Manuel utilisateur

DentalEZ

DentalEZ aXcs Basic-Duo Manuel utilisateur

DentalEZ

DentalEZ StarDental 430 SWL RA Manuel utilisateur

DentalEZ

DentalEZ StarDental Concentrix FX Manuel utilisateur

DentalEZ

DentalEZ Star Manuel utilisateur

DentalEZ

DentalEZ Aeras Ramvac RV4-12 Manuel utilisateur

DentalEZ

DentalEZ Star TITAN 3 5K MOTOR Manuel utilisateur

DentalEZ

DentalEZ StarDental Blis-sonic K Manuel utilisateur

DentalEZ

DentalEZ aXcs Series Manuel utilisateur

DentalEZ

DentalEZ Heritage Manuel utilisateur

DentalEZ

DentalEZ Star TITAN Manuel utilisateur

Manuels Équipement dentaire populaires d'autres marques

Vatech

Vatech EzRay Air VEX-P300 Manuel utilisateur

KaVo

KaVo GENTLEpower LUX Contra-angle 25 LP Manuel utilisateur

DENTSPLY

DENTSPLY SmartLite Focus Manuel utilisateur

LM ProPower CombiLED Manuel utilisateur

Owandy Radiology

Owandy Radiology RX-AC Manuel utilisateur

mectron

mectron Piezosurgery Manuel utilisateur

Belmont

Belmont CREDIA G1 Manuel utilisateur

Planmeca

Planmeca Sovereign Classic Manuel utilisateur

Bego

Bego Fornax T Manuel utilisateur

Renfert

Renfert SYMPRO Guide rapide

Ateco

Ateco AT-301 Manuel utilisateur

Nevadent

Nevadent NZPS 3 A1 Manuel utilisateur

Muss Dental

Muss Dental MA 50 Manuel technique

Diplomat

Diplomat Comfort Series Manuel utilisateur

Dentatus

Dentatus Nyström Manuel utilisateur

OMS

OMS DUKE EASY Manuel

OMS

OMS LINEA PATAVIUM Manuel

BRYANT DENTAL

BRYANT DENTAL Ignis Gesture A-494322 Manuel utilisateur