These operating instructions do not purport to cover all details or variation in equipment, nor to provide for every possible contingency to be met in connection with
installation, operation or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the Purchaserﾕs
purposes, the matter should be referred to the local Sales Office. The contents of these operating instructions shall not become part or modify any prior or existing
agreement, commitment or relationship. The Sales Contract contains the entire obligations. The warranty contained in the contract between the parties is the sole warranty.
Any statements contained herein do not create new warranties or modify the existing warranty.
For the purpose of this operating instructions and product labels,“Danger “ indicates death,
severe personal injury or substantial property damage will result if proper precautions are not taken.
For the purpose of this operating instructions and product labels,“Warning” indicates death,
severe personal injury or substantial property damage can result it proper precautions are not taken.
For the purpose of this operating instructions and product labels,
“Caution” indicates minor personal injury or property damage can result if proper precautions are not taken.
114.1
104 （2）
12 16.75
19.4
8.6
R3.3
±1.5
45.5
2.5
12.22 7.5
51.1
96.7
7.57.5 7.5
7.5 7.5
±1135.6 ±1
DIN EN50022 35X7.5
609.75
Input Terminal
Input Terminal
LED
=NOTES=
*1 At 100/200VAC,Ta = 25℃and maximum output power.
*2 For cases where conformance to various safety specs (UL,CSA,EN) are required,
input voltage range will be 100~230VAC(50/60Hz).
*3 Not applicable for the in-rush current to Noise Filter less than 0.2ms.
*4 Measure with JEITA RC-9131 probe, Bandwise of scope : 100MHz, and Please refer to Fig. A
for measurement of ripple voltage.
*5 85~264VAC,constant load at Line Regulation. No load-full load at Load Regulation.
*6 Constant current limit with automatic recovery. Avoid to operate over load or dead short for 30seconds.
*7 OVP circuit will shutdown output, manual reset.
*8 Measure by the each measuring method of UL,CSA,EN (at 60Hz).
*9 At 100VAC maximum output current.
*10 Refer to OUTPUT DERATING CURVE (BB018-01-03_)
APS75-30 Specification
■APS75-30 Specifications
(Please refer to Instruction manual before use)
■Basic Connection
MODEL
ITEM APS75-30
30VDC
0A
2.4A
72W
80%
85 〜264VAC
50Hz／60Hz (47Hz〜63Hz)
1.9A／1.2A (1.6A at 115VAC)
18A at 100VAC, 40A at 230VAC, Ta=25℃, Cold Start
Fixed
150m Vpp
±1%
±2%
2.8A〜4.8A
115%〜
0.2mA(Typ) at 100VAC／0.45mA(Typ) at 230VAC
20ms at 100VAC
-10℃〜+50℃: 100%, +55℃: 70%
30%〜90%RH（No dewdrop）
-30℃〜+85℃
10%〜95%RH（No dewdrop）
Convection Cooling
Input - FG: 2kVAC（20mA）, Input - Output: 3kVAC（20mA）,Output - FG: 500VDC（100mA）for 1 min
More than 100MΩat 25℃and 70%RH, Output - FG...500VDC
Mounting DIN rail : 10Hz〜55Hz, Half-wave Amplitude 0.5mm (1 hour), Mounting screw: 10Hz〜55Hz, Half-wave Amplitude 1mm (1 hour)
Mounting DIN rail : 150m/s2 (11ms), Mounting screw: 300m/s2 (18ms)
Apploved by UL1950, CSA950(C-UL), EN60950(TU
..V), Built to meet EN50295(AS-i)
Built to meet EN55011-B, EN55022-B, FCC-ClassB, VCCI-B
Built to meet EN55011-B, EN55022-B, FCC-ClassB, VCCI-B
Built to meet EN50082-2, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6
Noise Voltage : 2kV (Nomal, Common), pulse Width : 1us (Pulse Rise 1ns)
IP20
620g
45 ×135 ×105 mm (Refer to Outline Drawing)
【APS75-30】
APS75-30 Derating Curve
Unit:mm
Measurement point
for ripple Voltage
Fig. A
AS-i -
LineGND
AS-I+ A
0.1uF
■Output Derating Curve
OUTPUT DERATING CURVE
0
20
40
60
80
100
-10 0 10 20 30 40 50 60
LOAD(%)
Ta（℃）
MOUNTING : STANDARD MOUNTING ONLY
Outline drawing
APS75-30 Instruction Manual
BEFORE USING THIS PRODUCT
1. Terminal Explanation
DANGER
WARNING
CAUTION
䡬
1L1 : Input terminal Live line
䡬
2N : Input terminal Neutral line
䡬
3FG : Frame Ground
䡬
4POWER INDICATOR LED (Lights green during power output)
䡬
5AS-i + : AS-i Output terminal
䡬
6AS-i + : AS-i Output terminal
䡬
7Live GND : Live ground (Isolated from input FG)
䡬
8AS-iー：AS-i Output terminal
䡬
9AS-iー：AS-i Output terminal
■Outline
APS75-30 was developed to meet AS-Interface (Actuator Sensor
Interface) requirement.
AS-Interface is a kind of international open network for FA
application as the actuator-sensor level of the architecture.
AS-Interface applies one cable only that supplies the signal and
electric power stably together, so that will make cost saving and
cable reduction possible.
■Feature
●AS-Interface Power Supply
●Global scale wide input range: AC85-264V
●Output: 30V 2.4A max.
●DIN rail mountable type
■Safety standard
■AS-i
■EMC
●Immunity : Comform to EN50082-2
EN61000-4-2 （Electrostatics discharge）
EN61000-4-3 （Radiated electromagnetic field）
EN61000-4-4 （Electrical fast transient）
EN61000-4-5 （Surge）
EN61000-4-6 （Induced electromagnetic field）
CONFORM
EN55011-B, EN55022-B
CONFORM
VCCI-B
CONFORM
FCC-B
APPROVE
EN50295（AS-i）
APPROVE AS-International Association(No.37901)
MEET Low Voltage Directive
APPROVE
UL1950,CSA950（C-UL）
APPROVE
EN60950（TUV）
. .
EMI
Radiated
EmissonNoise
1. Nominal Output Voltage
2. Minimum Output Current
3. Maximum Output Current
4. Maximum Output Power
5. Efficiency (Typ) (*1)
6. Input Voltage Range (*2)
7. Input Frequency
8.
Input Current(100/200VAC)(Typ)
9. Inrush Current(Typ) (*3)
10. Output Voltage Range
11. Maximum Ripple & Noise (*4)
12. Initial Setting Voltage (*1)
13. Maximum Line & Load (*5)
& temperature Regulation
14. Over Current Protection (*6)
15.
Over Voltage Protection(Typ)
(*7)
16. Leakage Current (*8)
17. Hold-up Time (Typ) (*9)
18. Operating Temperature (*10)
19. Operating Humidity
20. Storage Temperature
21. Storage Humidity
22. Cooling
23. Withstand Voltage
24. Isolation Resistance
25. Vibration（IEC68-2-6）
26. Shock（IEC68-2-27）
27. Safety
28. Conducted Emission
29. Radiated Emission
30. Immunity
31. Impulse Noise Simulation
32. Degree of Protection（IEC529）
33. Weight(Typ.)
34. Size (W×H×D)
ASi-En-中身(刷り色P655CVC)02.2.144:13pmページ1
