Denon AVR-5805 Manuel

29.Mar.06

1/25

DENON AVR/AVC control protocol

Ver. 4.37a

Application model :AVR-5805/AVC-A1XV

Application terminal : RS-232C/ Ethernet

Connector specification

1. RS-232C

Connector type : DB-9pin female type, slave straight connection (DCE type)

( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )

Communication format :

Synchronous system : Tone step synchronization

Communication system : A half duplex

Communication speed : 9600bps

Character length : 8 bits

Parity control : None

Start bit : 1 bit

Stop bit : 1 bit

Communication procedure : Non procedural

Communication data length : 135 bytes (maximum)



29.Mar.06

2/25

2. Ethernet

Connector type ：RJ-45(10BASE-T/100BASE-TX)

Communication format ：

Communication system : A half duplex

Communication speed : 10Mbps/100Mbps

Communication port : TCP port 23 (telnet)

Communication data length : 135bytes (maximum)

AVR/AVC

Ethernet

Cross cable

AVR/AVC

HUB

Ethernet

Straight

cable

Ethernet

Straight

cable

Example ①

Example ②

29.Mar.06

3/25

NETWORK SETUP of AVR-5805/AVC-A1XV

>Procedure of Network Setup mode.

(1)Push the POWER switch during STANDARD button and 9CH STEREO button press simultaneously.

(2)Press SYSTEM SETUP button, then System Setup Menu appears on FL-display(and OSD)

(3)Select Option Setup and select Network Setup.

(4)Set parameters described below.

<DHCP> "ON"---Use this setting when DHCP server is on the local network.

"OFF"---Use this setting when DHCP server is not on the local network.

<IP Address> When <DHCP> sets "OFF”, please set IP address.

When <DHCP> sets "ON”, you can confirm the IP address that is set by server.

<Subnet Mask> When <DHCP> sets "OFF”, please set Subnet Mask.

When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.

<Gateway> Set the address of Gateway when Gateway is on the local network.

Do not set this parameter when Gateway is not on the local network.

<Primary DNS> Do not set this parameter.

<Second DNS> Do not set this parameter.

<Proxy> Set this parameter "OFF".

“OFF”---Use this setting when using the AVR-5805/AVC-A1XV connected in a network.

“ON”--- Use this setting when not using the AVR-5805/AVC-A1XV connected in a network.

This setting is reducing the power consumption in the standby mode.

29.Mar.06

4/25

Protocol specification

The following three data forms is defined.

COMMAND : The message sent to a system(AVR/AVC) from a controller(Touch Panel etc.)

A command to a system is given from a controller.

EVENT : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)

The result is sent, when a system is operated directly and a state changes.

*The form of EVENT presupposes that it is the same as that of COMMAND.

**Refer to the following table for the contents of COMMAND and EVENT.

RESPONSE : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)

if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.

The RESPONSE should be sent within 200ms of receiving the COMMAND.

*The form of RESPONSE presupposes that it is the same as that of EVENT.

Basic specification : The command by ASCII CODE, parameter expression

*ASCII CODE which can be used is from 0x20 to 0x7F : the alphabet and the number of 0-9 , and space (0x20) , Some signs ,

AND carriage return(0x0D)--- It is used only as a pause sign.

Command structure : COMMAND + PARAMETER + CR(0x0D)

COMMAND : ASCII CODE of 2 characters

ex. SI : Select Input source

MS : surround Mode Setting

MV : Master Volume setting

PW : system PoWer setting

PARAMETER : ASCII CODE ( up to 25 characters)

ex. DVD : function name

CDR/TAPE : function name

THX SURROUND EX : surround mode name

SUPER STADIUM : surround mode name

*Special Parameter--- ? : for request command

29.Mar.06

5/25

The example of a command * <CR> is the meaning of 0x0D.

SIDVD<CR> : Select Input source DVD

MSTHX SURROUND EX<CR> : surround Mode Set to THX SURROUND EX

MVUP<CR> : Master Volume UP

PWON<CR> : system PoWer ON

PWSTANDBY<CR> : system PoWer STANDBY

SI?<CR> : Request command for now playing input source>> Return RESPONSE ‘SI***<CR>’

29.Mar.06

6/25

Others

A) COMMAND is receivable also during transmission of EVENT.

B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels

returns as EVENT.

C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,

the data of an intact channel is set to "50".

D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (andalso the value of the channel

volume of all channels , It described in B) ) returns as EVENT.

E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME

does NOT return.

F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.

G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.

H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to

the another request commands(ex. SV command).

I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.

J) If the MASTER VOLUME & ZONE2 VOLUME（ZONE2 THEATER:5.1ch or 7.1ch system）& CHANNEL VOLUME set with 0.5dB step, the PARAMETER

(with COMMAND and RESPONSE, EVENT) defines three ASCII characters as bellows.

ex. MASTER VOLUME = +1.0dB : MV81<CR>

+0.5dB : MV805<CR>

0dB : MV80<CR>

-0.5dB : MV795<CR>

-1.0dB : MV79<CR>

| |

-79.5dB : MV005<CR>

-80.0dB : MV00<CR>

--- : MV99<CR>

* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.

29.Mar.06

7/25

COMMAND and PARAMETER list

COMMAND PARAMETER function example

PW ON POWER ON/STANDBY change PWON<CR>

STANDBY PWSTANDBY<CR>

MV UP MASTER VOLUME UP/DOWN , direct change to ***dB MVUP<CR>

DOWN MVDOWN<CR>

** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) MV80<CR>

CV FL UP CHANNEL VOLUME UP/DOWN , direct change to ***dB CVFL UP<CR>

FL DOWN ---FRONT Lch CVFL DOWN<CR>

FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50<CR>

FR UP CVFR UP<CR>

FR DOWN ---FRONT Rch CVFR DOWN<CR>

FR ** **:38 to 62 by ASCII , 50=0dB CVFR 50<CR>

C UP CVC UP<CR>

C DOWN ---CENTER ch CVC DOWN<CR>

C ** **:38 to 62 by ASCII , 50=0dB CVC 50<CR>

SW1 UP ---SWLeft or SWFront or SWMain ch (SWch 2 or 3SP) CVSW1 UP<CR>

SW1 DOWN ---SUBWOOFER (When SWch is 1SP) CVSW1 DOWN<CR>

SW1 ** **:00,38 to 62 by ASCII , 50=0dB, 00=OFF CVSW1 50<CR>

SW2 UP CVSW2 UP<CR>

SW2 DOWN ---SWRight or SWBack ch (SWch 2 or 3SP) CVSW2 DOWN<CR>

SW2 ** **:00,38 to 62 by ASCII , 50=0dB, 00=OFF CVSW2 50<CR>

LFE UP CVLFE UP<CR>

LFE DOWN ---LFEch (SWch 2 or 3SP) CVLFE DOWN<CR>

LFE ** **:00,38 to 62 by ASCII , 50=0dB, 00=OFF CVLFE 50<CR>

SLA UP CVSLA UP<CR>

SLA DOWN ---SURROUND L(A)ch CVSLA DOWN<CR>

SLA ** **:38 to 62 by ASCII , 50=0dB CVSLA 50<CR>

SRA UP CVSRA UP<CR>

SRA DOWN ---SURROUND R(A)ch CVSRA DOWN<CR>

SRA ** **:38 to 62by ASCII , 50=0dB CVSRA 50<CR>

MV , CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

The BOLD COMMANDS are new.

29.Mar.06

8/25

COMMAND PARAMETER function example

CV SLB UP CVSLB UP<CR>

SLB DOWN ---SURROUND L(B)ch CVSLB DOWN<CR>

SLB ** **:38 to 62 by ASCII , 50=0dB CVSLB 50<CR>

SRB UP CVSRB UP<CR>

SRB DOWN ---SURROUND R(B)ch CVSRB DOWN<CR>

SRB ** **:38 to 62 by ASCII , 50=0dB CVSRB 50<CR>

SBL UP CVSBL UP<CR>

SBL DOWN ---SURROUND BACK Lch (SBch 2SP) CVSBL DOWN<CR>

SBL ** **:38 to 62 by ASCII , 50=0dB CVSBL 50<CR>

SBR UP CVSBR UP<CR>

SBR DOWN ---SURROUND BACK Rch (SBch 2SP) CVSBR DOWN<CR>

SBR ** **:38 to 62 by ASCII , 50=0dB CVSBR 50<CR>

SB UP CVSBL UP<CR>

SB DOWN ---SURROUND BACKch (SBch 1SP) CVSBL DOWN<CR>

SB ** **:38 to 62 by ASCII , 50=0dB CVSBL 50<CR>

EXLA UP CVEXLA UP<CR>

EXLA DOWN ---EX L(A) ch CVEXLA DOWN<CR>

EXLA ** **:38 to 62 by ASCII , 50=0dB CVEXRA 50<CR>

EXRA UP CVEXRA UP<CR>

EXRA DOWN ---EX R(A) ch CVEXRA DOWN<CR>

EXRA ** **:38 to 62 by ASCII , 50=0dB CVEXRA 50<CR>

EXLB UP CVEXLB UP<CR>

EXLB DOWN ---EX L(B) ch CVEXLB DOWN<CR>

EXLB ** **:38 to 62 by ASCII , 50=0dB CVEXRB 50<CR>

EXRB UP CVEXRB UP<CR>

EXRB DOWN ---EX R(B) ch CVEXRB DOWN<CR>

EXRB ** **:38 to 62 by ASCII , 50=0dB CVEXRB 50<CR>

CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

The BOLD COMMANDS are new.

29.Mar.06

9/25

CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

The BOLD COMMANDS are new.

COMMAND PARAMETER function example

CV EXLC UP CVEXLC UP<CR>

EXLC DOWN ---EX L(C) ch CVEXLC DOWN<CR>

EXLC ** **:38 to 62 by ASCII , 50=0dB CVEXLC 50<CR>

EXRC UP CVEXRC UP<CR>

EXRC DOWN ---EX R(C) ch CVEXRC DOWN<CR>

EXRC ** **:38 to 62 by ASCII , 50=0dB CVEXRC 50<CR>

MU ON OUTPUT MUTE ON/OFF change MUON<CR>

OFF MUOFF<CR>

SI PHONO Select INPUT source SIPHONO<CR>

CD SICD<CR>

TUNER SITUNER<CR>

DVD SIDVD<CR>

VDP SIVDP<CR>

TV SITV<CR>

DBS SIDBS<CR>

VCR-1 SIVCR-1<CR>

VCR-2 SIVCR-2<CR>

VCR-3 SIVCR-3<CR>

VCR-4 SIVCR-4<CR>

V.AUX SIV.AUX<CR>

CDR/TAPE SICDR/TAPE<CR>

DTU SIDTU<CR>

ZM ON MAIN-ZONE ON/OFF change ZMON<CR>

OFF ZMOFF<CR>

SV DVD VIDEO SELECT mode set , and select source SVDVD<CR>

VDP SVVDP<CR>

TV SVTV<CR>

DBS SVDBS<CR>

VCR-1 SVVCR-1<CR>

VCR-2 SVVCR-2<CR>

VCR-3 SVVCR-3<CR>

VCR-4 SVVCR-4<CR>

V.AUX SVV.AUX<CR>

SOURCE VIDEO SELECT mode cancel SVSOURCE<CR>

29.Mar.06

10/25

COMMAND PARAMETER function example

SD AUTO set DIGITAL INPUT AUTO mode SDAUTO<CR>

PCM set DIGITAL INPUT force PCM mode SDPCM<CR>

DTS set DIGITAL INPUT force DTS mode SDDTS<CR>

RF ---Invalid at AVR-5805 SDRF<CR>

ANALOG set force ANALOG INPUT mode SDANALOG<CR>

EXT.IN-1 set EXT.IN-1 or EXT.IN mode SDEXT.IN-1<CR>

EXT.IN-2 set EXT.IN-2 mode SDEXT.IN-2<CR>

MS DIRECT SURROUND mode set MSDIRECT<CR>

PURE DIRECT MSPURE DIRECT<CR>

STEREO MSSTEREO<CR>

MULTI CH IN ---This is received as "SATNDARD". MSMULTI CH IN<CR>

MULTI CH DIRECT MSMULTI CH DIRECT<CR>

MULTI CH PURE D MSMULTI CH PURE D<CR>

DOLBY PRO LOGIC All are received as "STANDARD" , MSDOLBY PRO LOGIC<CR>

DOLBY PL2 the surround mode which changed return as EVENT. MSDOLBY PL2<CR>

DOLBY PL2x MSDOLBY PL2X<CR>

DOLBY DIGITAL MSDOLBY DIGITAL<CR>

DOLBY D EX MSDOLBY D EX<CR>

DTS NEO:6 MSDTS NEO:6<CR>

DTS SURROUND MSDTS SURROUND<CR>

DTS ES DSCRT6.1 MSDTS ES DSCRT6.1<CR>

DTS ES MTRX6.1 MSDTS ES MTRX6.1<CR>

DOLBYH/P MSDOLBYH/P<CR>

DTS+DOLBYH/P MSDTS+DOLBYH/P<CR>

HOME THX CINEMA All are received as "THX SURROUND" , MSHOME THX CINEMA<CR>

THX5.1 the surround mode which changed return as EVENT.MSTHX5.1<CR>

THX U2 CINEMA MSTHX U2 CINEMA<CR>

THX MUSIC MODE MSTHX MUSIC MODE<CR>

THX GAMES MODE MSTHX GAMES MODE<CR>

THX6.1 ---Operate as Matrix6.1 or Discrete6.1 MSTHX6.1<CR>

THX SURROUND EX MSTHX SURROUND EX<CR>

WIDE SCREEN MSWIDE SCREEN<CR>

The BOLD COMMANDS are new.

Autres manuels pour AVR-5805

Ce manuel convient aux modèles suivants

Autres manuels Denon Récepteur

Denon

Denon AVR 2308CI - AV Receiver Manuel utilisateur

Denon

Denon AVR-X6400H Manuel utilisateur

Denon

Denon AVR-3805 Manuel

Denon

Denon AirPlay AVR-3311CI Manuel de la liste des pièces

Denon

Denon M-CR612 Manuel utilisateur

Denon

Denon AVR-X4100W Manuel utilisateur

Denon

Denon AVR-2105 Manuel utilisateur

Denon

Denon AVR-1600 Manuel utilisateur

Denon

Denon AVR-4802R Manuel utilisateur

Denon

Denon AVR-1911 Manuel utilisateur

Denon

Denon AVR-683 Manuel utilisateur

Denon

Denon AVR-485S Manuel utilisateur

Denon

Denon AVR-1912 Manuel utilisateur

Denon

Denon AVR-X1100W Manuel utilisateur

Denon

Denon AVR-X3200W Manuel utilisateur

Denon

Denon Ceol Piccolo DRA-N4 Manuel utilisateur

Denon

Denon AVR-S530BT Manuel utilisateur

Denon

Denon AVR-2807 Manuel utilisateur

Denon

Denon AVR-988 Manuel utilisateur

Denon

Denon MULTEQXT AVR-4306 Manuel utilisateur

Denon

Denon AVR-3808 Manuel utilisateur

Denon

Denon AVR-1404/484 Manuel utilisateur

Denon

Denon AVR-487 Manuel utilisateur

Denon

Denon IN-Command AVR-X4000 Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur