Denon MC4000 Manuel utilisateur

VirtualDJ 8 –Denon MC4000

Table of Contents

INSTALLATION.........................................................................................................................3

Connections ...........................................................................................................................3

Firmware.................................................................................................................................3

Drivers....................................................................................................................................3

VirtualDJ 8 Setup ...................................................................................................................3

Advanced Setup.....................................................................................................................4

A. MIXER ...................................................................................................................................6

B. BROWSER............................................................................................................................6

C. SAMPLER.............................................................................................................................7

D. DECK CONTROLS...............................................................................................................8

E. HOTCUES.............................................................................................................................9

HotCues 1-4 mode.................................................................................................................9

HotCues 5-8 mode.................................................................................................................9

Hot-Loop 1-4 mode..............................................................................................................10

Loop Rolls mode ..................................................................................................................10

F. EFFECTS & LOOPS...........................................................................................................11

G. MICROPHONE ...................................................................................................................13

H. MASTER .............................................................................................................................13

I. REAR PANEL.......................................................................................................................14

J. FRONT PANEL ...................................................................................................................14

INPUTS & RECORDING.........................................................................................................15

VirtualDJ 8 –Denon MC4000

INSTALLATION

Connections

Use the included power adapter (6V DC, 3A, center-positive) to connect MC4000 to a power

outlet. Connect the unit’s USB socket with a USB port of your computer. Connect a pair of

amplified speakers or amplifier to the Master Output sockets (RCA or XLR). Power on

MC4000.

Firmware

Windows & Mac

Currently there is no firmware available, but please make sure of that by visiting the MC4000

product page. http://denondj.com/products/view/mc4000

Drivers

Windows only

Download and install the latest ASIO drivers from: http://denondj.com/products/view/mc4000

No drivers need to be installed for Mac OSX computers

VirtualDJ 8 Setup

Download and install VirtualDJ 8 from

http://www.virtualdj.com/download/index.html

(in case you have not done already)

Once VirtualDJ 8 is launched, a Login Window

will appear. Login with your virtualdj.com

account’s credentials.

A Pro Infinity, a PLUS or a Pro Subscription

License is required to use the Denon DJ

MC4000. Without any of the above Licenses,

the controller will operate for 10 minutes each

time you restart VirtualDJ.

http://www.virtualdj.com/buy/index.html

VirtualDJ 8 –Denon MC4000

A detection window will appear next, asking

to use or not the pre-defined audio setup

with the built-in sound card of the MC4000.

Select “Use Soundcard” and click OK

The unit is now ready to operate.

Advanced Setup

MIDI Operation

The unit should be visible in the

CONTROLLERS tab of Config and the

“factory default” available/selected from the

Mappings drop-down list.

The factory default Mapping offers the

functions described in this Manual, however

those can be adjusted to your needs via VDJ

Script actions.

Find more details at

http://www.virtualdj.com/wiki/VDJscript.html

AUDIO Setup

The unit has a pre-defined Audio setup and

a special button in the AUDIO tab of Config

to provide that.

See also Inputs & Recording.

Please read the manual of the unit for further connections/capabilities.

http://denondj.com/products/view/mc4000

For further software settings please refer to the User Guides of VirtualDJ 8.

http://www.virtualdj.com/wiki/PDFManuals.html

VirtualDJ 8 –Denon MC4000

S. SHIFT. Press and hold this button to access secondary functions of other

controls on the MC4000

M. PAD MODE. Press and hold this button to access a different mode for the

HotCue PADS or Sampler PADS

VirtualDJ 8 –Denon MC4000

A. MIXER

1. CROSSFADER. Blends audio

between the left and right decks

2. VOLUME. Use these faders to

adjust the Volume of each deck.

3. VU METERS The Led Meters

indicate the Output Level of each

deck

4. CUE/PFL. Press these buttons to

send this deck's pre-fader signal to

the Cue Channel for monitoring.

When engaged, the button will be

lit.

5. FILTER. Use these knobs to apply

a High/Low Pass Filter on the

left/right decks.

6. EQ LOW. Adjusts the low (bass)

frequencies of each deck.

7. EQ MID. Adjusts the middle (mid)

frequencies of each deck

8. EQ HIGH. Adjusts the high (treble)

frequencies of each deck

9. GAIN. Adjusts the audio level

(gain) of the corresponding deck

B. BROWSER

10. LOAD. Use these buttons to load the selected track from the Browser to the left or

right deck. Hold the same button for more than 2 seconds to unload the same deck.

Hold SHIFT down and then use these buttons to clone the deck to the opposite one.

11. LIBRARY. Use this encoder to scroll through Folders or Files. Hold SHIFT down and

use this encoder to scroll faster (+/- 10 tracks per step). Push the encoder to set

focus to the Songs List.

12. BACK Use this button to set focus to the Folders List. If the focus is on the Folders

list, use this button to expand/collapse sub-folders.

Hold SHIFT down and then use this button to cycle through the available center

panels of the default GUI of VirtualDJ (Mixer, Video, Scratch an Master view)

VirtualDJ 8 –Denon MC4000

13. LOAD/PREP. Press this button to add the selected track to the Automix List of

Sideview.

Hold SHIFT down to set focus to Sideview.

If focus is on the Sideview hold SHIFT down and then use this button to cycle

through the Sideview windows (Automix, Sidelist, Karaoke, Sampler and Shortcuts)

Hold SHIFT down and press this button for more than 2 seconds to open/close the

Sideview.

C. SAMPLER

14. SAMPLER BUTTONS. Use these buttons to

trigger Samples 1 to 4 of the selected Sampler

Bank of VirtualDJ.

Hold down any of the PAD MODE buttons (M)

and then use the left Sampler buttons to select

the previous and next Sampler Bank.

Hold down any of the PAD MODE button (M) and

then use the right Sampler buttons to select the

previous and next Sampler mode (On/Off,

Stutter, Hold and Unmute)

Depending on the selected Sampler mode, hold

SHIFT down and then use the same Sampler

buttons to stop the playing samples.

15. SAMPLER VOLUME. Use this knob to adjust the

Master Volume of the Sampler (will affect the

Output Volume of all Samples)

VirtualDJ 8 –Denon MC4000

D. DECK CONTROLS

16. PLAY. Plays / Pauses the

track. Press and hold

SHIFT and then press this

button to "stutter-play" the

track from the last set Cue

Point.

17. CUE. When the Deck is

paused, you can set a

Cue Point by moving the

Platter to place the Audio

Pointer at the desired

location and then pressing

the Cue Button.

During playback, you can

press the Cue Button to

return the track to this

Cue Point. (If you did not

set a Cue Point, then it

will return to the beginning

of the track.).

If the Deck is paused, you can press and hold the Cue Button to play the track from

the Temporary Cue Point. Releasing the Cue Button will return the track to the

temporary Cue Point and pause it.

To continue playback without returning to the Temporary Cue Point, press and hold

the Cue Button, then press and hold the Play Button, and then release both buttons.

Press and hold SHIFT and then press this button to return to the beginning of the

track.

18. SYNC. Press this button to automatically match the corresponding Deck's tempo

and phase with the opposite Deck's (or the Master Deck’s if using a 4 decks Skin)

tempo and phase. Hold SHIFT down and then press this button to set this deck as

Master Deck (for 4 decks skins).

19. PITCH BEND. Press and hold these buttons down to temporary speed up/slow

down the song while pressed. When released, the track playback will return to the

speed designated by the Pitch Fader.

Hold SHIFT down and then use these buttons to move the track forward or

backwards by 8 beats (seek)

20. KEYLOCK. Press this button to "lock" the track's pitch to its original key. The track's

tempo will remain at the speed designated by the Pitch Fader. Hold SHIFT down and

then use this button to select the next available range of the Pitch Fader ( from ±6%,

±8%, ±10%, ±12%, ±20%, ±25%, ±33%, ±50% to ±100%).

21. PITCH. Adjust the track's playback speed (tempo).

VirtualDJ 8 –Denon MC4000

22. JOG. Touch sensitive jogwheel. Use the jogwheel to scratch (if Vinyl mode is

selected) or pitch bend. The Jogwheel also offers Loop In and Loop Out point

adjustment (see Effects & Loops)

23. SCRATCH. Press this button to set the Jogwheel to Vinyl (Scratch) or CD (Bend)

mode. In Vinyl mode, use the outer part of the Jogwheel to bend (temporary speed

up –slow down the tempo of the track).

Hold SHIFT down and then keep this button down to play the track in reverse. When

the button is released, the track will continue playing from the position it would have

been if never used (CENSOR).

E. HOTCUES

The 4Pads (24) offer 4 different

modes, depending on the PAD MODE

selection button (M).

Hold the PAD MODE button down and

then press one the 4 Pads to select a

mode as per the image.

HotCues 1-4 mode

Hold the PAD MODE button (M) down and then press Pad Nr1 button to select the HotCues

1-4 mode. The LED of the PAD MODE selection button will be turned off after the selection.

Each one of the 4 Pads assigns a Hot

Cue Point (1 to 4) or returns the track to

that Hot Cue Point.

When a Pad is unlit, you can assign a Hot

Cue Point by pressing it at the desired

point in your track. Once it is assigned,

the Hot Cue Button will light up blue.

Hold SHIFT and then press any of the 4 Pads to delete its assigned Hot Cue Point.

HotCues 5-8 mode

Hold the PAD MODE button (M) down and then press Pad Nr2 button to select the HotCues

5-8 mode. The LED of the PAD MODE selection button will be turned on blue after the

selection.

VirtualDJ 8 –Denon MC4000

Same as the HotCues 1-4 mode, each

one of the 4 Pads assigns a Hot Cue

Point (5 to 8) or returns the track to that

Hot Cue Point.

When a Pad is unlit, you can assign a

Hot Cue Point by pressing it at the

desired point in your track. Once it is

assigned, the Pad will light up blue.

Hold SHIFT and then press any of the 4 Pads to delete its assigned Hot Cue Point.

Hot-Loop 1-4 mode

Hold the PAD MODE button (M) down and then press Pad Nr3 button to select the Hot-

Loops 1-4 mode. The LED of the PAD MODE selection button will be turned on red after the

selection.

Each one of the 4 Pads assigns a Hot

Cue Point (1 to 4) or returns the track to

that Hot Cue Point, but in both cases, it

also triggers a Loop.

The currently selected length will be

used for the triggered Loop

While loop is triggered, press the same

Pad to disable the Loop.

The LED of the Pad will turn red if the HotCue is assigned and will flash while the loop is

triggered.

Hold SHIFT down and then press a pad to delete its assigned Hot Cue Point.

Use the LOOP HALF and LOOP DOUBLE buttons (38) to half and double the size of the

applied Loop.

Loop Rolls mode

Hold the PAD MODE button (M) down and then press Pad Nr4 button to select the Loop

Rolls mode. The LED of the PAD MODE selection button will be turned on purple after the

selection.

Each one of the 4 Pads triggers a

momentary (while pressed) Loop Roll of a

different size in beats as per the image.

Once the Pad is released, the track will

continue to play from the position it would

have been if the Loop was never triggered.

Autres manuels pour MC4000

Table des matières

Autres manuels Denon Mixeur musical

Denon

Denon DN-X400 Manuel utilisateur

Denon

Denon DN-X120 Manuel utilisateur

Denon

Denon DN-410X Manuel utilisateur

Denon

Denon DN-X600 Manuel utilisateur

Denon

Denon DNX050 - PRO DJ TWO CHANNEL MIXER Manuel utilisateur

Denon

Denon MC6000 MKII Manuel utilisateur

Denon

Denon DN-X1100 - DJ Mixer Manuel utilisateur

Denon

Denon DN-X100 Manuel utilisateur

Denon

Denon DN-410X Manuel utilisateur

Denon

Denon DN-X300 Manuel utilisateur

Denon

Denon DN-312X Manuel utilisateur

Denon

Denon DN-X300 Manuel utilisateur

Denon

Denon MC6000MK2 Manuel utilisateur

Denon

Denon DN-X1100 - DJ Mixer Manuel utilisateur

Denon

Denon DN-X120 Manuel utilisateur

Denon

Denon MC2000 Manuel utilisateur

Denon

Denon DN-X1 20 Manuel utilisateur

Denon

Denon DNX500 - Pro DJ Mixer Manuel utilisateur

Denon

Denon DN-MC6000 Manuel utilisateur

Denon

Denon MC4000 Manuel utilisateur

Denon

Denon DN-X1500S - DJ Mixer Manuel utilisateur

Denon

Denon DN-X400 Manuel utilisateur

Denon

Denon DN-X300 Manuel utilisateur

Denon

Denon DN-X400 Manuel utilisateur

Manuels Mixeur musical populaires d'autres marques

Neve

Neve 8816 Manuel utilisateur

Mackie

Mackie Onyx Analogue Mixer Manuel utilisateur

Behringer

Behringer EUROPOWER PMP518M Manuel utilisateur

Peavey

Peavey S-32 Sanctuary Series Manuel utilisateur

Rane

Rane MP 4 Manuel utilisateur

True

True T9 Touchscreen Console Manuel utilisateur

Studiomaster

Studiomaster Air Pro 24 Manuel utilisateur

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Manuel utilisateur

Roland

Roland M-160 Manuel utilisateur

Yamaha

Yamaha MR1642 Manuel utilisateur

Ecler

Ecler MAC40v Manuel utilisateur

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Manuel utilisateur

Veeder-Root

Veeder-Root TLS-350 Series Manuel utilisateur

Alto

Alto APM80.QUAD Manuel utilisateur

Omnitronic

Omnitronic PM-211 Manuel utilisateur

SoundCraft

SoundCraft B400 Manuel utilisateur

Roland

Roland SoundCanvas SC-8820 Manuel utilisateur

CARVIN

CARVIN RX 1200 Manuel utilisateur