Denon S-301 Manuel utilisateur

-1-

DENON AVR/AVC control protocol

Ver. 4.0

Application model : S-301

Application terminal : RS-232C

Connector specification

Connector type : DB-9pin female type, slave straight connection (DCE type)

( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )

Communication format :

Synchronous system: Tone step synchronization

communication system : Ahalf duplex

Communication speed : 9600bps

Character length : 8 bits

Parity control : None

Start bit : 1 bit

Stop bit : 1 bit

Communication procedure : Non procedural

Communication data length : 135 bytes (maximum)

-2-

Protocol specification

The following three data formsis defined.

COMMAND : The message sent to a system(AVR/AVC) from a controller(Touch Panel etc.)

A command to a system is given from a controller.

EVENT : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)

The result is sent, when a system is operated directly and a state changes.

*The form of EVENT presupposes that it is the same as that of COMMAND.

**Refer to the following table for the contents of COMMAND and EVENT.

RESPONSE : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)

if the ‘request command’(COMMAND+?+CR(0x0D)) has came from a controller.

The RESPONSE should be sent within 200ms of receiving the COMMAND.

*The form of RESPONSE presupposes that it is the same as that of EVENT.

Basic specification : The command by ASCII CODE, parameter expression

*ASCII CODE which can be used is from 0x20 to 0x7F : the alphabet and the number of 0-9 , and space (0x20) , Some signs ,

AND carriage return(0x0D)--- It is used only as a pause sign.

Command structure : COMMAND + PARAMETER + CR(0x0D)

COMMAND : ASCII CODE of 2 characters

ex. SI : Select Input source

MS : surround Mode Setting

MV : Master Volume setting

PW : system PoWer setting

PARAMETER : ASCII CODE ( up to 25 characters)

ex. DVD : function name

CDR/TAPE-1 : function name

THX SURROUND EX : surround mode name

SUPER STADIUM : surround mode name

*Special Parameter--- ? : for request command

-3-

The example of a command * <CR> is the meaning of 0x0D.

SIDVD<CR> : Select Input source DVD

MSTHX SURROUND EX<CR> : surround Mode Set to THX SURROUND EX

MVUP<CR> : Master Volume UP

PWON<CR> : system PoWer ON

PWSTANDBY<CR> : system PoWer STANDBY

SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’

-4-

Others

A) COMMAND is receivable also during transmission of EVENT.

B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns

as EVENT.

C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data

of an intact channel is set to "50".

D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel volume

of all channels , It described in B) ) returns as EVENT.

E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME does NOT

return.

F) Although EVENTof SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.

G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.

H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to the another

request commands(ex. SV command).

I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.

J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three ASCIIcharacters

as bellows.

ex. MASTER VOLUME = +1.0dB : MV81<CR>

+0.5dB : MV805<CR>

0dB : MV80<CR>

-0.5dB : MV795<CR>

-1.0dB : MV79<CR>

| |

-79.5dB : MV005<CR>

-80.0dB : MV00<CR>

--- : MV99<CR>

* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.

-5-

COMMAND and PARAMETER list

COMMAND PARAMETER function example Receive?

PW ON POWER ON/STANDBY change PWON<CR> ○

STANDBY PWSTANDBY<CR> ○

MV UP MASTER VOLUME UP/DOWN , direct change to **dB MVUP<CR> ○

DOWN MVDOWN<CR> ○

** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) MV80<CR> ○

CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP<CR> ○

FL DOWN ---FRONT Lch CVFL DOWN<CR> ○

FL ** **:00 to 99 by ASCII , 50=0dB CVFL 50<CR> ○

FR UP CVFR UP<CR> ○

FR DOWN ---FRONT Rch CVFR DOWN<CR> ○

FR ** **:00 to 99 by ASCII , 50=0dB CVFR 50<CR> ○

C UP CVC UP<CR> ×

C DOWN ---CENTERch CVC DOWN<CR> ×

C ** **:00 to 99 by ASCII , 50=0dB CVC 50<CR> ×

SW UP CVSW UP<CR> ○

SW DOWN ---SUBWOOFERch CVSW DOWN<CR> ○

SW ** **:00 to 99 by ASCII , 50=0dB CVSW 50<CR> ○

SL UP CVSL UP<CR> ×

SL DOWN ---SURROUND LchCVSL DOWN<CR> ×

SL ** **:00 to 99 by ASCII , 50=0dB CVSL 50<CR> ×

SR UP CVSR UP<CR> ×

SR DOWN ---SURROUND Rch CVSR DOWN<CR> ×

SR ** **:00 to 99 by ASCII , 50=0dB CVSR 50<CR> ×

SBL UP ---SURROUND BACK Lch (SBch 2SP) CVSBL UP<CR> ×

SBL DOWN CVSBL DOWN<CR> ×

SBL ** **:00 to 99 by ASCII , 50=0dB CVSBL 50<CR> ×

SBR UP ---SURROUND BACK Rch (SBch 2SP) CVSBR UP<CR> ×

SBR DOWN CVSBR DOWN<CR> ×

SBR ** **:00 to 99 by ASCII , 50=0dB CVSBR 50<CR> ×

MV , CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

-6-

COMMAND PARAMETER function example Receive?

CV SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP<CR> ×

SB DOWN CVSB DOWN<CR> ×

SB ** **:00 to 99 by ASCII , 50=0dB CVSB 50<CR> ×

MU ON OUTPUT MUTE ON/OFF change MUON<CR> ○

OFF MUOFF<CR> ○

SI PHONO Select INPUT source SIPHONO<CR> ×

CD SICD<CR> ×

TUNER SITUNER<CR> ○

DVD SIDVD<CR> ○

VDP SIVDP<CR> ×

TV SITV<CR> ○

DBS/SAT ---Select DBS function at AVR-3805 SIDBS/SAT<CR> ×

VCR-1---Select AUX1 Function at D-EX SIVCR-1<CR> ○

VCR-2---Select AUX2 Function at D-EX SIVCR-2<CR> ○

VCR-3---Invalid at AVR-3805 SIVCR-3<CR>

V.AUX ---Select PORTABLE Function at D-EX SIV.AUX<CR> ○

CDR/TAPE1 ---Select CDR/TAPE function at AVR-3805

---Select AUX3 Function at D-EX SICDR/TAPE1<CR> ○

MD/TAPE2 ---Invalid at AVR-3805 SIMD/TAPE2<CR> ×

USB SIUSB<CR> ○

IPOD SIIPOD<CR> ○

ZM ON MAIN-ZONE ON/OFF change at AVR-3805 ZMON<CR> ×

OFF ZMOFF<CR> ×

Z1 PHONO MULTI ZONE-3 mode set , and select source at AVR-3805 Z1PHONO<CR> ×

| ---The name of PARAMETER is |

CDR/TAPE1 the same as that of the time of SI COMMAND. Z1MD/TAPE2<CR>

SOURCE MULTI ZONE-3 mode cancel at AVR-3805 Z1SOURCE<CR> ×

UP MULTI ZONE-3 VOLUME UP/DOWN , direct change to ***dB Z1UP<CR> ×

DOWN at AVR-3805 Z1DOWN<CR> ×

** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) Z180<CR> ×

ON MULTI ZONE-3 ON/OFF change at AVR-3805 Z1ON<CR> ×

OFF Z1OFF<CR> ×

CV , Z1 COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

-7-

COMMAND PARAMETER function example Receive?

Z2 PHONO MULTI ZONE-2 mode set , and select source at AVR-3805 Z2PHONO<CR> ×

| ---The name of PARAMETER is |

CDR/TAPE1 the same as that of the time of SI COMMAND. Z2MD/TAPE2<CR>

SOURCE MULTI ZONE-2 mode cancel Z2SOURCE<CR> ×

UP MULTI ZONE-2 VOLUME UP/DOWN , direct change to ***dB Z2UP<CR> ×

DOWN Z2DOWN<CR> ×

** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) Z280<CR> ×

ON MULTI ZONE-2 ON/OFF change at AVR-3805 Z2ON<CR> ×

OFF Z2OFF<CR> ×

SR PHONO REC SELECT mode set , and select source SRPHONO<CR> ×

| ---The name of PARAMETER is |

CDR/TAPE1 the same as that of the time of SI COMMAND. SRMD/TAPE2<CR>

SOURCE REC SELECT mode cancel SRSOURCE<CR> ×

SV DVD VIDEO SELECT mode set , and select source SVDVD<CR> ×

VDP SVVDP<CR> ×

TV SVTV<CR> ×

DBS/SAT ---Select DBS function at AVR-3805 SVDBS/SAT<CR> ×

VCR-1 SVVCR-1<CR> ×

VCR-2 SVVCR-2<CR> ×

VCR-3 ---Invalid at AVR-3805 SVVCR-3<CR> ×

V.AUX SVV.AUX<CR> ×

SOURCE VIDEO SELECT mode cancel SVSOURCE<CR> ×

SD AUTO set DIGITAL INPUT AUTO mode SDAUTO<CR> ○

PCM set DIGITAL INPUT force PCM mode SDPCM<CR> ○

DTS set DIGITAL INPUT force DTS mode SDDTS<CR> ○

RF ---Invalid at AVR-3805 SDRF<CR> ×

ANALOG set force ANALOG INPUT mode SDANALOG<CR> ○

EXT.IN-1 set EXT.IN-1 mode ---Set EXT.IN mode at AVR-3805 SDEXT.IN-1<CR> ×

EXT.IN-2 set EXT.IN-2 mode ---Invalid at AVR-3805 SDEXT.IN-2<CR> ×

Z2 COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

-8-

COMMAND PARAMETER function example Receive?

MS DIRECT SURROUND mode set MSDIRECT<CR> ×

PURE DIRECT MSPURE DIRECT<CR> ×

STEREO MSSTEREO<CR> ○

MULTI CH IN MSMULTI CH IN<CR> ×

MULTI CH DIRECT MSMULTI CH DIRECT<CR> ×

MULTI CH PURE D MSMULTI CH PURE D<CR> ×

DOLBY PRO LOGIC All are received as "DOLBY SURROUND" ,MSDOLBY PRO LOGIC<CR> ×

DOLBY PL2 the surround mode which changed return as EVENT. MSDOLBY PL2<CR> ×

DOLBY PL2x MSDOLBY PL2X<CR> ×

DOLBY DIGITAL MSDOLBY DIGITAL<CR> ×

DOLBY D EX MSDOLBY D EX<CR> ×

DTS NEO:6 All are received as "DTS SURROUND" ,MSDTS NEO:6<CR> ×

DTS SURROUND MSDTS SURROUND<CR> ×

DTS ES DSCRT6.1 MSDTS ES DSCRT6.1<CR> ×

DTS ES MTRX6.1 MSDTS ES MTRX6.1<CR> ×

DOLBY H/P ---Invalid at AVR-3805 MSDOLBY H/P<CR> ○

DTS+DOLBY H/P ---Invalid at AVR-3805 MSDTS+DOLBY H/P<CR> ○

HOME THX CINEMA ---Invalid at AVR-3805 MSHOME THX CINEMA<CR> ×

THX5.1 ---Invalid at AVR-3805 MSTHX5.1<CR> ×

THX U2 CINEMA ---Invalid at AVR-3805 MSTHX U2 CINEMA<CR> ×

THX MUSIC MODE ---Invalid at AVR-3805 MSTHX MUSIC MODE<CR> ×

THX6.1 ---Invalid at AVR-3805 MSTHX6.1<CR> ×

THX SURROUND EX ---Invalid at AVR-3805 MSTHX SURROUND EX<CR>×

WIDE SCREEN MSWIDE SCREEN<CR> ×

5CH STEREO Both are received as "5CH/7CH STEREO" ,MS5CH STEREO<CR> ×

7CH STEREO the surround mode which changed return as EVENT. MS7CH STEREO<CR> ×

SUPER STADIUM MSSUPER STADIUM<CR> ×

ROCK ARENA MSROCK ARENA<CR> ○

JAZZ CLUB MSJAZZ CLUB<CR> ○

CLASSIC CONCERT MSCLASSIC CONCERT<CR> ×

MONO MOVIE MSMONO MOVIE<CR> ×

MATRIX MSMATRIX<CR> ×

VIDEO GAME MSVIDEO GAME<CR> ×

VIRTUAL MSVIRTUAL<CR> ×

-9-

COMMAND PARAMETER function example Receive?

MS MPEG2 AAC ---Invalid at AVR model MSMPEG2 AAC<CR> ×

AAC+DOLBY EX ---Invalid at AVR model MSAAC+DOLBY EX<CR> ×

DVS REF. MSDVS REF.<CR> ○

DVS WIDE MSDVS WIDE<CR> ○

PS TONE DEFEAT ON PARAMETER setting PSTONE DEFEAT ON<CR> ×

TONE DEFEAT OFF TONE DEFEAT ON/OFF PSTONE DEFEAT OFF<CR> ×

SB:MTRX ON SURROUND BACK SP MODE set PSSB:MTRX ON<CR> ×

SB:NON MTRX ---MTRX ON = SURR.EX ON = DSCRT ON PSSB:NON MTRX<CR> ×

SB:PL2xCINEMA (@THX) (@ES DSCRT) PSSB:PL2X CINEMA<CR> ×

SB:PL2xMUSIC PSSB:PL2X MUSIC<CR> ×

SB:OFF PSSB:OFF<CR> ×

CINEMA EQ.ON CINEMA EQ. ON/OFF PSCINEMA EQ.ON<CR> ○

CINEMA EQ.OFF PSCINEMA EQ.OFF<CR> ○

MODE : MUSIC CINEMA / MUSIC / GAME / PL mode change PSMODE:MUSIC<CR> ○

MODE : CINEMA (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.) PSMODE:CINEMA<CR> ○

MODE : GAME ---SB=ON：PL2x mode / SB=OFF：PL2 mode PSMODE:GAME<CR> ×

MODE : PRO LOGIC --- GAME can change DOLBY PL2 & PL2x mode PSMODE:PRO LOGIC<CR> ○

MODE : EMULATION PSMODE:EMULATION<CR> ×

MODE : OFF --- PL can change ONLY DOLBY PL2 mode PSMODE:OFF<CR> ×

ROOM EQ:NORMAL ROOM EQ mode direct change PSROOM EQ:NORMAL<CR> ×

ROOM EQ:FRONT PSROOM EQ:FRONT<CR> ×

ROOM EQ:FLAT PSROOM EQ:FLAT<CR> ×

ROOM EQ:MANUAL PSROOM EQ:MANUAL<CR> ×

ROOM EQ:OFF PSROOM EQ:OFF<CR> ×

DELAY UP AUDIO DELAY UP/DOWN , direct change to ***ms PSDELAY UP<CR> ○

DELAY DOWN ***:000 to 999 by ASCII , 000=0ms, 200=200ms PSDELAY DOWN<CR> ○

DELAY *** (3 digits) ---AVR5805 can be operated from 0 to 200 PSDELAY ***<CR> ○

TF UP TUNER Frequency UP/DOWN , direct change TFUP<CR> *○

DOWN TFDOWN<CR> *○

****** (6 digits) --- ****.** kHz at AM band (>050000 is AM.)

****.** MHz at FM band (<050000 is FM.) TF105000<CR>

(1050.00kHz at AM) ○

TP UP TUNER PRESET CH UP/DOWN , direct change to No.** TPUP<CR> ○

DOWN TPDOWN<CR> ○

**(PRESET No.) TPA1<CR> (PRESET No.”A1”) ○

TP11<CR> (PRESET No.”11”)

-10 -

COMMAND PARAMETER function example Receive?

TM TUNER BAND , MODE Select ○

AM ---Band set to AM TMAM<CR>

FM ---Band set to FM TMFM<CR> ○

AUTO ---Tuning mode set to AUTO mode TMAUTO<CR> *○

MANUAL ---Tuning mode set to MANUAL mode TMMANUAL<CR> *○

CO 080 Sub-Woofer Crossover Frequency CO080<CR> ○

120 80Hz / 120Hz / 150Hz / 180Hz CO120<CR> ○

150 CO150<CR> ○

180 CO180<CR> ○

TF, TP, TM COMMAND : '*' parameters can NOT operate when INPUT source isn’t TUNER.

Autres manuels pour S-301

Table des matières

Autres manuels Denon Système de cinéma maison

Denon

Denon ADV-700 Manuel utilisateur

Denon

Denon DHT-500SD Manuel utilisateur

Denon

Denon DHT-500SD Manuel utilisateur

Denon

Denon S-102 Manuel utilisateur

Denon

Denon S-101 Manuel utilisateur

Denon

Denon DHT-500SD Manuel utilisateur

Denon

Denon DHT-S416 Manuel utilisateur

Denon

Denon S-32 Guide de l'utilisateur

Denon

Denon S-52 Dimensions

Denon

Denon DHT-1000DV Manuel utilisateur

Denon

Denon DHT-483DVD Manuel utilisateur

Denon

Denon DHT-485DV Manuel utilisateur

Denon

Denon DHT-1312XP Manuel utilisateur

Denon

Denon DHT FS5 - X-SPACE Surround System Home Theater Speaker... Manuel utilisateur

Denon

Denon DHT-1312XP Manuel utilisateur

Denon

Denon S-102 Manuel utilisateur

Denon

Denon S-101 Manuel utilisateur

Denon

Denon DHT FS5 - X-SPACE Surround System Home Theater Speaker... Manuel utilisateur

Denon

Denon AVR-1907 Guide de l'utilisateur

Denon

Denon AVR 2809CI - AV Receiver Guide de l'utilisateur

Denon

Denon DHT-488BA Manuel utilisateur

Denon

Denon AVR 2809CI - AV Receiver Manuel utilisateur

Denon

Denon DHT FS5 - X-SPACE Surround System Home Theater Speaker... Manuel utilisateur

Denon

Denon DHT-485DV Instructions de montage

Manuels Système de cinéma maison populaires d'autres marques

Samsung

Samsung HT-ES4200K Manuel utilisateur

Harman Kardon

Harman Kardon HS 100 Manuel utilisateur

Samsung

Samsung HT-P10 Manuel utilisateur

Philips

Philips HTS5131 Mode d'emploi

Goodmans

Goodmans GDVD19SWS Manuel utilisateur

Moxi

Moxi media center Manuel utilisateur

Samsung

Samsung HT-EM35 Manuel utilisateur

LG HE903PAW Manuel utilisateur

Bose

Bose SoundTouch 520 Manuel utilisateur

Sony

Sony BDV-N990W Manuel utilisateur

Manta

Manta GK-500 Manuel utilisateur

Sharp

Sharp SBW800 Manuel utilisateur

Philips

Philips HTS3541 Manuel utilisateur

LG LHT799 Manuel utilisateur

Samsung

Samsung HT-TWZ415 Manuel utilisateur

Loewe

Loewe REFERENCE 52 SL FHD+ 200 NMP Manuel utilisateur

Samsung

Samsung AH68-02166R Manuel utilisateur

RCA

RCA 600-Watt Manuel utilisateur