Demon International Hurricane E Manuel utilisateur
Hurricane E
Tornado E Bowser
Tornado E Mini-Bowser
Including electric start variants and bowser washers
Declaraon of Conformity
(E.H.S.R.)
We, Demon Internaonal Limited of Abbots Close, Lee Mill Industrial Estate,
Ivybridge, Devon, PL21 9GA, declare that this machine must be operated in
accordance with the operaon and safety instrucons as supplied with this
machine.
This machine is manufactured in accordance with the following standards
and recommendaons.
HSE PVB PM29 - BS5415 Part - BS5415 Secon 2.4 1986
This instrucon manual is relevant only to the following machine and will not
be kept updated unless specically requested by the customer. However,
any changes to the operang procedure or changes which might aect the
safety of this machine will be noed to the registered owner
Machine Type
Serial Number
Working Pressure
Date of Supply
Rev 1
Operaons Manual
Demon Baery E Range
Technical Specicaons
Hurricane E Tornado E Bowser
Motor 24 Volt DC Motor 24 Volt DC
Pump XT 11/14 Pump XT 11/14
Pressure 1120—1500 PSI Pressure 1120—1500 PSI
Flow 11 lpm Flow 15 lpm
Nozzle 2504 Nozzle 2504
Baery 135amp sealed Lithium Baery 200amp sealed lithium
Unloader Minimac 4/B Unloader Minimac 4/B
Pump Oil 10W/40 Pump Oil 10W/40
Tornado E Mini-Bowser
Motor 24 Volt DC
Pump XT 11/14
Pressure 1120—1500 PSI
Flow 13 lpm
Nozzle 2504
Baery 135amp sealed lithium
Unloader Minimac 4/B
Pump Oil 10W/40
Machine Hurricane E Electron Bowser Electron Mini-Bowser
Valve Kit 1864 1864 1864
Seal Kit 1874 1874 1874
Piston Kit 2629 2629 2629
Oil Kit 1872 1872 1872
Support Ring
Kit
O Rings
Kits for the Baery E Range
FAULT CAUSE REMEDY
Machine stops suddenly
Or will not start.
Low oil
Flat Baery (Electron )
Check and top up oil
Re-charge
Sudden pressure loss. Water supply failed.
No chemical
Check water supply.
Check chemical drum, close valve
Low pressure
HP nozzle worn or un-
loader set
Incorrectly.
Replace HP nozzle. Set unloader
to correct seng.
Low pressure with noise and
vibraon.
Valves worn or blocked.
Piston seals worn.
Pump sucking air.
Clean/replace as required.
Replace.
Check water supply pipe and
unions.
Pump will not by-pass. Non return valve dirty
or jammed. Clean or replace.
Water drips from pump box. Pump seals worn. Replace.
Oil drips from pump boom. Oil seal worn. Replace.
Oil is milky in colour. Water ingress through
oil lter plug. Rinse pump out and replace oil.
IF IN DOUBT ASK—OUR ADVICE IS FREE AND CAN SAVE YOU MONEY
Fault Finder
DAILY CHECK THE FOLLOWING
a. Oil level - top up as required.
b. Baery percentage - top up as required.
c. All hose unions for leaks- replace O rings if leaking.
d. Hose condion - cuts etc.
EVERY 500 HOURS OR SIX MONTHS (WHICHEVER COMES FIRST)
a. Drain and replace pump oil.
d. Clean water lter.
e. Replace high pressure nozzle.
EVERY 1000 HOURS OR 12 MONTHS (WHICHEVER COMES FIRST)
a. Complete 500 hour service.
b. Replace pump seals.
c. Replace oil seals.
d. Check unloading pressure and safety valve pressure and adjust.
The above service schedules are intended as a guide only, actual service mes
and replacements parts required will vary according to the area and the usage
of the machine.
Minimum Service Schedules
Preparaon
Water Supply:
AEnsure there is an adequate water supply either from the mains or mini bowser tank.
BAach water supply hoses to suitable tap or immerse the sucon hose with approved
sucon lter into the reservoir.
NOTE: ONLY CLEAN WATER SHOULD BE USED. THE PUMP MAY BE DAMAGED IF DIRTY OR
CONTAMINATED WATER IS ALLOWED TO PASS THROUGH THE PUMP.
Hoses: High pressure outlet.
For all models use 3/8” RIT or 3/8” R2T hoses.
ACheck the condion of the “O” rings in the ends of the hose.
BAach the high pressure hose to the pump connecon.
CAach the spray gun to opposite ends of the high pressure hose.
OPERATION
AFully charge baery.
BCheck baery isolator is showing green.
CTo start DC Motor turn key and pull switch up.
DAdjust pressure regulator as required to obtain working pressure if required.
EDirect lance on to surface to be cleaned. Press the lance trigger.
FNOTE: The high pressure water will cause the gun to “kick” make sure you have a rm grip
of the gun and lance.
GLeaving the pressure washer on by-pass for prolonged periods without operang the lance
Will cause the water in the pump to heat up. This heat build up may damage the seals and
Valves in the pump.
HOn compleon of operaon stop the DC motor.
IOperate lance trigger
JRelease residual pressure in gun and lance by operang trigger.
Charging
The E range is ed with an indicator light which will glow green.
Baeries MUST NOT be fully discharged before re-charging to maximise life cycles of the
baeries.
When using Cleaning Agents:
A. Set machine up as for water.
B. Connect detergent hose to machine and place lter end into detergent.
C. On compleon of work, ush through hose and gun with clean water to remove any residu-
al detergent.
NOTE: CHEMICAL PICKUP ONLY OPERATES AT PRESSURES BELOW 250PSI.
OPEN LANCE VALVE FULLY TO OBTAIN THIS PRESSURE
.
Tornado Mini Bowser E General Arrangement
Tank Lid TOR0116
Lid Seals TORO1115
Tank TOR0113
Filter MTM85002
WHEEL400
Pump to hose reel hose
15 Mtr Hose
HH00050MVGH
R
Hose Reel MTM20021
15 mtr Hose HH00050MVGHR
Castor Wheel WHEEL500
Ball Valve
BV12169
Brass Swivel
MTM20060
O Rings
MTM20024
Unloader ARMM4B/C
Pressure Gauge
DEM20620
ARXT11.14 Pump
Hurricane - E General Arrangement
WHEEL400
Knob DEM102255
Stop/start
Pressure Gauge
DEM20620
Unloader
ARMM4B/C
ARXT11.14 Pump
Bowser E General Arrangement
Hose Reel
MTM20022
Pump to hose reel hose
Jockey Wheel
XLE00320
30 Mtr Hose
HH00100MVGHR
ARXT11.14 Pump
Unloader Minimac 4/B
24V DC Motor
200 amp 24V sealed baery
Charging
When the machine requires charging please follow the instrucons below.
1. Switch o the pressure washer.
2. Release the pressure in the lance.
3. Plug in the mains lead to 13 amp supply.
4. Charger should start on 24V Cold seng (if not set with the charge mode buon)
5. If the charger does not start as the baeries are totally discharged push the
Pre-charge buon. Then complete charging as instrucon 4.
Pre-Charge Buon
Charge Indicators
Charge Mode
Pre-Charge Buon
Baery Charger
13amp Plug
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Demon International Rondelle
