DELTAVISION DVR 1016 Manuel utilisateur
0
DVR Manual version 4.020 Nov. 22, 2001 rev.2
Digital Video
Recorder
Model:
DVR 1016
Software version 4.020
User’s Guide
Nov. 22, 2001 rev. 2
1
DVR Manual version 4.020 Nov. 22, 2001 rev.2
Read all safety cautions and operating instructions before using
the DVR. Keep these instructions for future reference.
§To reduce the risk of electrical shock, do not remove the cover
of the unit. There are no user serviceable parts inside. Refer
servicing to qualified personnel.
§To prevent fire or shock hazard, do not expose the unit to
rain or moisture.
§Any unauthorized modification to this equipment could
result in the revocation of the authorization to operate the
equipment.
2
DVR Manual version 4.020 Nov. 22, 2001 rev.2
Product Introduction
Thank you for purchasing the Deltavision DVR 1016 Digital Video Recorder.
•This is the user’s guide for the DVR 1016.
•This guide provides a hardware and software sections.
•It is recommended that you read this manual before using the DVR, even though you may be
familiar to similar products.
Repairs
•If treated with care, this DVR will provide years of satisfactory performance. However, in the
event of difficulty, the user or installer is advised not to attempt to make repairs or to open the
case. Servicing should always be referred to qualified personnel.
3
DVR Manual version 4.020 Nov. 22, 2001 rev.2
Please verify the following points before installing or using the DVR.
lAvoid any locations that has a high moisture, dust or dirt content.
lAvoid any locations that is subject to direct sun light or heat.
lHigh or low temperature are not suitable for the DVR.
The recommended temperature range is between 5°C and 35°C (41°Fand 95°F)
lAvoid any locations that is subject to high voltage or magnetic interference.
lBe careful not to insert any debris in any ventilation openings.
lBe sure the DVR is off and remove the power cord before installation.
lEnsure there is enough clearance for cables in the rear of the DVR.
Before installation
4
DVR Manual version 4.020 Nov. 22, 2001 rev.2
Contents
Mouse
Key Board
Power Cable
User Guide
Verify that the following items are included when you open the box.
Should there be anything missing contact your distributor .
(Monitor must be purchased separately and capable of 1024 x 768.)
Communication transforming cable
( used for PAN/TILT CAMERA )
Serial Port Connection Cable
Front mouse port interconnection cable
DVR
Keys
5
DVR Manual version 4.020 Nov. 22, 2001 rev.2
1.Front of System 7
2. Rear of System 8
3. Connecting Speed Domes and aux. monitor 9
4. Connecting PSTN and ISDN 10
5. Connecting external Sensor 11
6. Connecting Control outputs 11
1. How to install
1.1 Display mode 13
1.2 Password setting 14
1.3 Hardware setup 15
1.4 Motion detection setup 19
1.5 Schedule setup 23
1.6 Screen split setup 25
1.7 Communication setup 26
1.8 Site Information 31
1.9 Password setup 33
1.10 Audio setup 34
1.11 System setup 35
Motion Tracking (future option)
1.12 Storage setup 36
1.13 E-Map setup 37
1. Configuring the Program
2. Software user guide
Table of Contents
6
DVR Manual version 4.020 Nov. 22, 2001 rev.2
2. Display mode Setup
2.1 Selecting split screen 38
2.2 Changing between Pan/Tilt & surveillance mode 39
2.3 Controlling Pan/Tilt 40
2.4 Using E-Map 41
3.1 Search mode 43
3.2 Selecting search date and time 44
3.3 Basic search –Playing data 45
3.4 Basic search –Screen magnification and brightness 47
3.5 Inteli search –Selecting data 48
3.6 Inteli search –Controls 49
3.7 Audio playback 51
3.8 Data backup 55
3.6 Printing searched data 64
3. Search mode Setup
7
DVR Manual version 4.020 Nov. 22, 2001 rev.2
1.
1. Front of System
1-Never press the reset switch unless the system is completely frozen.
2-The front filter should be cleaned periodically.
1
2
CDR
8
DVR Manual version 4.020 Nov. 22, 2001 rev.2
2. Rear of System
9
DVR Manual version 4.020 Nov. 22, 2001 rev.2
3. Connecting Speed Domes
3. Connecting Speed Domes
and Aux. Monitor
and Aux. Monitor
Caution: Care is to be taken with the polarity of the serial interconnection
to the speed domes. Wrong polarity might cause damage.
!
To COM1:
RUN LED
TXD LED
RXD LED
Call / Spot Monitor
IR Remote Receiver
RS232 to COM1:
via serial port connection
cable
RS-422 to Speed Dome
Signal +
Signal -
NC
Front mouse port interconnection cable
Serial port connection cable
Table des matières
