Delta Electronics Ethernet Communication Module DVPEN01-SL Manuel utilisateur

DVPEN01-SL

Ethernet Communication Module

Application Manual

Ethernet Communication Module DVPEN01-SL

DVP-PLC Application Manual 1

Warning

Please read this instruction carefully before use and follow this instruction to operate the device in order to prevent

damages on the device or injuries to staff.

Switch off the power before wiring.

RTU-DNET is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne dust,

humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the

device (e.g. key or specific tools are required for operating the enclosure) in case danger and damage on the

device may occur.

RTU-DNET is to be used for controlling the operating machine and equipment. In order not to damage it, only

qualified professional staff familiar with the structure and operation of RTU-DNET can install, operate, wire and

maintain it.

DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check

all the wirings again before switching on the power and DO NOT touch any terminal when the power is switched

on. Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference.

Table of Contents

1INTRODUCTION...................................................................................................................................3

1.1 Functions.....................................................................................................................................3

1.2 Specifications ..............................................................................................................................3

2PRODUCT PROFILE & OUTLINE .......................................................................................................4

2.1 Dimension ...................................................................................................................................4

2.2 Product Profiles...........................................................................................................................4

2.3 LED Indicators.............................................................................................................................5

2.4 RJ-45 PIN Definition....................................................................................................................5

3INSTALLATION & WIRING ..................................................................................................................5

3.1 Installation ...................................................................................................................................5

4CONTROL REGISTER (CR) ................................................................................................................6

4.1 Control Registers in DVPEN01-SL..............................................................................................6

4.2 Explanations on CR ....................................................................................................................8

4.3 Numbering of Left-Side Extension Modules..............................................................................12

5SETTING UP SOFTWARE.................................................................................................................13

5.1 Setting up Communication & Searching for Modules................................................................13

5.2 Basic Settings ...........................................................................................................................16

5.3 Network Settings .......................................................................................................................18

5.4 Setting up E-Mails .....................................................................................................................20

5.5 Data Exchange..........................................................................................................................22

Ethernet Communication Module DVPEN01-SL

DVP-PLC Application Manual

5.6 IP Filter ..................................................................................................................................... 23

5.7 Static ARP Table ....................................................................................................................... 24

5.8 Setting up Password................................................................................................................. 25

5.9 Returning to Default Setting ..................................................................................................... 26

5.10 Export & Import of DVPEN01-SL Files ..................................................................................... 27

5.11 Recording IP Address ............................................................................................................... 28

6APPLICATION EXAMPLES............................................................................................................... 29

6.1 Setting up IP and Communicating through WPLSoft................................................................ 29

6.2 Connecting the PC with DVPEN01-SL through LAN ................................................................ 32

6.3 Setting up IP and Communicating through WPLSoft................................................................ 36

6.4 Setting up Password and Clearing Password .......................................................................... 37

6.5 When the Password is Lost (Returning to Default Setting by RS-232)..................................... 39

6.6 IP Filter Protection .................................................................................................................... 40

6.7 Setting up Static ARP Table ...................................................................................................... 42

6.8 Application of E-Mail................................................................................................................. 43

6.9 Application of Data Exchange (1) ............................................................................................. 45

6.10 Application of Data Exchange (2) ............................................................................................. 47

6.11 Application of Data Exchange (3) ............................................................................................. 48

6.12 Application of Modbus TCP Master (1)..................................................................................... 49

Ethernet Communication Module DVPEN01-SL

DVP-PLC Application Manual 3

1 Introduction

Thank you for choosing DVPEN01-SL module. To correctly install and operate DVPEN01-SL, please read

the manual carefully before using the module.

DVPEN01-SL is an Ethernet communication module for remote setting and communication through

WPLSoft. DVPEN01-SL is able to send E-mails, automatically correct the RTC in DVP28SV11R/T and

exchange data. It supports Modbus TCP communication protocol and can conduct remote monitoring by using

SCADA (Supervisor Control And Data Acqusition) software or HMI (Human Machine Interfaces). DVPEN01-SL

can be the master of Modbus TCP, sending out Modbus TCP instrcutions and controlling the peripheral

equipment. In addition, under MDI/MDI-X auto-detection, it does not need to use a crossing cable. See the

contents below for more detailed instructions on DVPEN01-SL module.

1.1 Functions

zAuto-detects 10/100Mbps transmission speed

zMDI/MDI-X auto-detection

zSupports Modbus TCP protocol (at the same time supports Master and Slave mode)

zAble to send out E-mails

zAuto-corrects the RTC in PLC through the Internet time correction function

zSupports point-to-point data exchange (Max. data exchange length: 200 bytes)

1.2 Specifications

Internet interface

Item Specification

Interface RJ-45 with Auto MDI/MDIX

Number of ports 1 Port

Transmission method IEEE802.3, IEEE802.3u

Transmission cable Category 5e

Transmission speed 10/100 Mbps Auto-Detect

Network protocol ICMP, IP, TCP, UDP, DHCP, SMTP, NTP, Modbus TCP

Serial communication interface

Item Specification

Interface RS-232

Number of ports 1 Port

Transmission cable DVPACAB230, DVPACAB215, DVPACAB2A30, DVPACAB2B10

Environment

Item Specification

Noise immunity

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV

Analog & Communication I/O: 1KV

Damped-Oscillatory Wave: Power Line: 1KV

RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m

Environment Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), Pollution degree 2;

Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)

Ethernet Communication Module DVPEN01-SL

DVP-PLC Application Manual

Item Specification

Vibration/ Shock Resistance Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

Electrical specifications

Item Specification

Power supply voltage 24VDC (-15% ~ 20%) (Power is supplied by the internal bus of MPU.)

Power consumption 1.5W

Insulation voltage 500V

Weight (g) 92 (g)

2 Product Profile & Outline

2.1 Dimension

LAN

RS-232

LINK

DVPEN01

RS-232

POWER

100M

60 [2.362]

90 [3.543]

3 [0.118]

Unit：mm [inches]

2.2 Product Profiles

LAN

RS-232

LINK

DVPEN01

RS-232

POWER

100M

1. Model name 6. Fixing tenon for extension unit/module

2. Extension port to connect device 7. Fixing clip for extension unit/module

3. Extension port to connect extension module 8. RS-232 connection port

4. POWER, LINK, RS-232, 100M indicators 9. Ethernet RJ-485 connection port

5. DIN rail clip

Ethernet Communication Module DVPEN01-SL

DVP-PLC Application Manual 5

2.3 LED Indicators

Indicator Color Indication

POWER Green Power indication

RS-232 Red Communication status of the series port

100M Orange Network connection status

LINK Green Network communication speed

2.4 RJ-45 PIN Definition

RJ-45 sketch Terminal No. Definition Explanation

1 Tx+ Positive pole for data transmission

2 Tx- Negative pole for data transmission

3 Rx+ Positive pole for data receiving

6 Rx- Negative pole for data receiving

4, 5, 7, 8 - N/C

3 Installation & Wiring

This section gives instructions on how to connect DVPEN01-SL with PLC MPU and how to connect

DVPEN01-SL to the network.

3.1 Installation

Connect PLC MPU to DVPEN01-SL

zAdjust the extension clip on the left side of the MPU.

zMeet the extension port of the MPU with DVPEN01-SL as shown in the figure below.

zFasten the extension clip.

DVP28SV

LAN

RS-232

LINK

100M

DVPEN01

POWER

Connect DVPEN01-SL to other extension modules

zTo connect DVPEN01-SL with the other extension module, lift the extension clip of the extension

module by a screwdriver and open the side cover.

Ethernet Communication Module DVPEN01-SL

DVP-PLC Application Manual

Connect DVPEN01-SL to the Network

Connect DVPEN01-SL to the Ethernet Hub by twisted pair cable CAT-5e. DVPEN01-SL has Auto MDI/MDIX

function; therefore, DVPEN01-SL does not need to use a crossing cable between the PC and DVPEN01-SL.

Network connection between the PC and DVPEN01-SL:

4 Control Register (CR)

4.1 Control Registers in DVPEN01-SL

CR#

HW LW Attribute Content Explanation

#0 R Model name Set up by the system; read only. Model code of DVPEN01-SL

= H’4050

#1 R Firmware version Displaying the current firmware version in hex.

#2 R Communication mode b0: Modbus TCP mode; b1: data exchange mode

#3 W E-Mail Event 1 trigger Set up whether to send E-Mail 1

#4 W E-Mail Event 2 trigger Set up whether to send E-Mail 2

#5 W E-Mail Event 3 trigger Set up whether to send E-Mail 3

#6 W E-Mail Event 4 trigger Set up whether to send E-Mail 4

Ethernet

PC Maste

DVP28SV

LAN

RS-232

LINK

100M

DVPEN01

POWER

DVP28SV

DVPEN01

DVP28SV

LAN

RS-232

LINK

100M

DVPEN01

POWER

DVP28SV

DVPEN01

Ethernet Communication Module DVPEN01-SL

DVP-PLC Application Manual 7

CR#

HW LW Attribute Content Explanation

#7 R

Status of E-Mail 1, 2 b0 ~ b7: Current status of E-Mail 2

b8 ~ b15: Current status of E-Mail 1

#8 R Status of E-Mail 3, 4 b0 ~ b7: Current status of E-Mail 4

b8 ~ b15: Current status of E-Mail 3

#9 R/W

E-Mail 1 additional

message Filled in by the user, and it will be send by E-mail.

#10 R/W

E-Mail 2 additional

message Filled in by the user, and it will be send by E-mail.

#11 R/W

E-Mail 3 additional

message Filled in by the user, and it will be send by E-mail.

#12 R/W

E-Mail 4 additional

message Filled in by the user, and it will be send by E-mail.

#13 R/W Data exchange trigger Set up whether to send out data in data exchange mode

#14 R Status of data exchange Displaying current status of data exchange.

#24 ~ #15 - Reserved

#26 #25 R/W Destination IP Destination IP address for data exchange

#27 - Reserved

#28 R/W Destination Slave ID Destination Slave ID for data exchange

#48 ~ #29 R/W Data transmission buffer Buffer for transmitted data in data exchange

#68 ~ #49 R Data receiving buffer Buffer for received data in data exchange

#69 R/W DHCP/Static IP Selecting DHCP or Static IP

#71 #70 R/W IP address Setting up IP address

#73 #72 R/W Subnet mask Setting up subnet mask of DVPEN01-SL

#75 #74 R/W Gateway Setting up default gateway IP address

#76 R IP status Displaying current IP status

#80 ~ #77 - Reserved

#81 R/W

Read address for data

exchange Slave transmission buffer address for data exchange

#82 R/W

Read length for data

exchange Number of registers for read data

#83 R/W

Received address for

data exchange Buffer address for the receiving Master in data exchange

#84 R/W

Written-in address for

data exchange Buffer address for the receiving Slave in data exchange

#85 R/W

Written-in length for data

exchange Number of registers for data transmission

#86 R/W

Transmission address

for data exchange Master transmission buffer address for data exchange

#110 ~ #87 - Reserved

#111 R/W 8-bit processing mode Setting up Modbus TCP Master control as 8-bit mode

#113 ~ #112 - Reserved

#114 R/W Modbus TCP time-out Setting up Modbus TCP time-out (in ms)

#115 R/W Modbus TCP trigger Setting up whether to send out data in Modbus TCP mode

#116 R/W Modbus TCP status Displaying current status of Modbus TCP mode

#118 #117 R/W Modbus TCP

destination IP Setting up destination IP address for Modbus TCP transaction

Ethernet Communication Module DVPEN01-SL

DVP-PLC Application Manual

CR#

HW LW Attribute Content Explanation

#119 R/W Modbus TCP data length Setting up the data length for Modbus TCP transaction

#219 ~ #120 R/W Modbus TCP data buffer Data buffer of Modbus TCP for storing sending/receiving data

#248 ~ #220 - Reserved

#251 R Error code Displaying the errors. See table of error codes in the following

section for more information.

#255 ~ #252 - Reserved

Symbols “R” refers to “able to read data by FROM instrcution”; “W” refers to “able to write data by TO

instrcution”.

4.2 Explanations on CR

CR#0:Model Name

Explanations:

1. Model code of DVPEN01-SL = H’4050.

2. You can read the model code in the program to see if the extension module exists.

CR#1: Firmware Version

Explanations:

The firmware version of DVPEN01-SL is displayed in hex, e.g. H’0100 indicates version V1.00.

CR#2: Communication Mode

Explanations:

Bit No. Mode “0” “1”

b0 Modbus TCP Disable Enable

b1 Data exchange Disable Enable

E-mail Functions

CR#3 ~ 6: E-Mail Event 1 ~ 4 Trigger

Explanations:

When the CR is set as “1”, E-mail sending will be enabled. After the sending is completed, the

CR will automatically be reset as “0”. Note: Please trigger by differential instrcutions.

CR#7 ~ 8: Status of E-Mail 1 ~ 4

Explanations:

1. CR#7_b0 ~ b7: current status of E-Mail 2; CR#7_b8 ~ b15: current status of E-Mail 1.

2. CR#8_b0 ~ b7: current status of E-Mail 4; CR#8_b8 ~ b15: current status of E-Mail 3.

3. Table of E-Mail status

CR value E-Mail status

0 Not been sent

1 Being processed

2 E-Mail sending is successful

Table des matières

Autres manuels Delta Electronics Carte réseau

Delta Electronics

Delta Electronics Extension Drive Board EB Series Manuel utilisateur

Delta Electronics

Delta Electronics DVP Series PLC DVP04TC-H2 Manuel utilisateur

Delta Electronics

Delta Electronics DeviceNet Slave Communication Module IFD9502 Manuel utilisateur

Delta Electronics

Delta Electronics LCP-1250A4FSR Manuel utilisateur

Delta Electronics

Delta Electronics LonWorks Communication Module LN-01 Manuel utilisateur

Delta Electronics

Delta Electronics Distribution Box TAP-CN01/02/03 Manuel utilisateur

Delta Electronics

Delta Electronics Analog Output Module DVP02DA-S Manuel utilisateur

Delta Electronics

Delta Electronics Function Card DVP-EH Manuel utilisateur

Delta Electronics

Delta Electronics DeviceNet Slave Communication Module... Manuel utilisateur

Delta Electronics

Delta Electronics Digital I/Oextension Unit DVP-ES/EX Manuel utilisateur

Delta Electronics

Delta Electronics High-speed Counter Module DVP-01HC Manuel utilisateur

Delta Electronics

Delta Electronics Ethernet Communication Module IFD9507 Manuel utilisateur

Delta Electronics

Delta Electronics TP05 Manuel utilisateur

Delta Electronics

Delta Electronics Network Device GEN Manuel utilisateur

Delta Electronics

Delta Electronics Igniter IGT005 Manuel utilisateur

Delta Electronics

Delta Electronics DeviceNet CME-DN01 Manuel utilisateur

Delta Electronics

Delta Electronics Digital Keypad KPE-LE01 Manuel utilisateur

Delta Electronics

Delta Electronics EME-A22A Manuel utilisateur

Delta Electronics

Delta Electronics CANopen Slave Station Communication Module... Manuel utilisateur

Delta Electronics

Delta Electronics Ignition Coil IGT001 Manuel utilisateur

Delta Electronics

Delta Electronics Digital Keypad KPE-LE02 Manuel utilisateur

Delta Electronics

Delta Electronics Analog Output Module DVP04DA-S Manuel utilisateur

Delta Electronics

Delta Electronics AC Motor Drive VFD007S23A Manuel utilisateur

Delta Electronics

Delta Electronics Inverter ESI 48/230V Manuel utilisateur

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITXR Manuel utilisateur