Delta Electronics DVP-SS2 Manuel utilisateur

2010

699

DVP-1160070-01

- 1 -

………………………………………………………………… ENGLISH ……………………………………………………………………

Thank you for choosing Delta DVP-SS2. DVP-SS2 is a 14-point (8DI + 6DO) PLC MPU,

offering various instructions and with 8k steps program memory, able to connect to all

DVP-S series extension models, including digital I/O (max. 480 I/O points) and analog

modules (for A/D, D/A conversion and temperature measurement). 4 groups of

high-speed (10kHz) pulse output satisfy all kinds of applications. DVP-SS2 is small in

size and easy to install.

aThis instruction sheet only provides introductory information on electrical

specifications, general specifications, installation and wiring. For detailed information

on programming and instructions, please refer to “DVP-SS2 Operation Manual:

Programming”. For information about optional peripherals, please see individual

product instruction sheet enclosed with DVP-SS2.

aThis is an OPEN TYPE device and therefore should be installed in an enclosure free

of airborne dust, humidity, electric shock and vibration. The enclosure should prevent

non-maintenance staff from operating the device (e.g. key or specific tools are

required to open the enclosure) in case danger and damage on the device may

occur.

aDO NOT connect input AC power supply to any of the I/O terminals; otherwise

serious damage may occur. Check all the wiring again before switching on the power.

Make sure the ground terminal is correctly grounded in order to prevent

electromagnetic interference. DO NOT touch any terminals when the power is

switched on.

Product Profile

[ Figure 1 ]

60.00

EXTENSION

PORT

90.00

3.00

Unit: mm

1. POWER, RUN, ERROR indicator 8. Nameplate

2. RUN/STOP switch 9. Extension port

3. I/O port for program communication (RS-232) 10. DIN rail mounting slot (35mm)

4. DIN rail clip 11. Extension unit clip

5. I/O terminals 12. RS-485 communication port

6. I/O point indicator 13. Mounting rail for extension module

7. Mounting hole for extension module 14. DC power input

Electrical Specifications

Model

Item DVP14SS211R DVP14SS211T

Power supply voltage

24VDC (-15% ~ 20%)

(with counter-connection protection on the polarity of DC input power)

DVPPS01(PS02): input 100-240VAC, output 24VDC/1A(PS02: 2A)

Inrush current Max. 7.5A@24VDC

- 2 -

Model

Item DVP14SS211R DVP14SS211T

Fuse capacity 1.85A/30VDC, Polyswitch

Power consumption 1.8W 1.5W

Power protection With counter-connection protection on the polarity of DC input power

Insulation resistance > 5MΩ(all I/O point-to-ground: 500VDC)

Noise immunity

ESD: 8kV Air Discharge

EFT: Power Line: 2kV, Digital I/O: 1kV, Analog & Comm. I/O: 250kKV

RS: 26MHz ~ 1GHz, 10V/m

Grounding

The diameter of grounding wire cannot be smaller than the wire

diameter of terminals L and N (All DVP units should be grounded

directly to the ground pole).

Operation / storage Operation: 0°C ~ 55°C (temp.), 50 ~ 95% (humidity), Pollution degree2

Storage: -25°C ~ 70°C (temp.), 5 ~ 95% (humidity)

Vibration / shock

resistance

International standards: IEC61131-2, IEC 68-2-6 (TEST

Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

Weight (g) 97g 82.5g

Input Point

Spec.

Items 24VDC (-15% ~ 20%) single common port input

Input No. X0 ~ X3 X4 ~ X7

Input type DC (SINK or SOURCE)

Input Current (± 10%) 24VDC, 5mA

Input impedance 4.7kΩ

Max. frequency 20kHz 10kHz

OffOn > 15VDC

Action

level OnOff < 5VDC

OffOn < 10μs < 20μs

Response

time OnOff < 20μs < 50μs

Filter time Adjustable within 0 ~ 20ms by D1020 (Default: 10ms)

Output Point

Spec.

Items Relay Transistor

Output No. Y0 ~ Y5 Y0 ~ Y3 Y4, Y5

Max. frequency 1Hz 10kHz 1kHz

Working voltage 250VAC, < 30VDC 5 ~ 30VDC #1

Resistive 1.5A/1 point (5A/COM) 0.5A/1 point (3A/COM)

Inductive #2 15W (30VDC)

Max. load

Lamp 20WDC/100WAC 2.5W (30VDC)

OffOn 20μs 100μs

Response

time OnOff Approx. 10ms 30μs 100μs

#1: UP, ZP must work with external auxiliary power supply 24VDC (-15% ~ +20%), rated

consumption approx. 1mA/point.

#2: Life curves

Contact

Current(A)

0.5

0.1 0.2

0.3 0.7 12

200

300

500

100

1000

2000

3000

Operation(X10)

120VAC Resistive

30VDC Inductive(t=7ms)

240VAC Inductive(cos 0.4)

120VAC Inductive(cos =0.4)

30VDC

Inductive

(t=40ms)

[ Figure 2 ]

- 3 -

I/O Configuration

Input Output I/O Configuration

Model Point Type Point Type Relay Transistor

14SS211R Relay

14SS211T

8 DC

(Sink Or Source) 6

Transistor

S/S

Note: The layout of output terminals on DVP-SS2 is different from that on DVP-SS.

Dimension & Installation

Please install the PLC in an enclosure with sufficient

space around it to allow heat dissipation, See

[Figure 3].

Direct Mounting: Use M4 screw according to the

dimension of the product.

DIN Rail Mounting: When mounting the PLC to

35mm DIN rail, be sure to use the retaining clip to

stop any side-to-side movement of the PLC and

reduce the chance of wires being loose. The retaining clip is at the bottom of the PLC.

To secure the PLC to DIN rail, pull down the clip, place it onto the rail and gently push

it up. To remove the PLC, pull the retaining clip down with a flat screwdriver and gently

remove the PLC from DIN rail.

Wiring

1. Use 22-16AWG (1.5mm) single or multiple core wire

on I/O wiring terminals. See the figure in the right hand

side for its specification. PLC terminal screws should be

tightened to 1.90 kg-cm (1.65 in-lbs) and please use only

60/75ºC copper conductor.

22-16AWG

< 1.5mm

2. DO NOT wire empty terminal. DO NOT place the I/O signal cable in the same wiring

circuit.

3. DO NOT drop tiny metallic conductor into the PLC while screwing and wiring. Tear

off the sticker on the heat dissipation hole for preventing alien substances from

dropping in to ensure normal heat dissipation of the PLC.

Power Supply

The power input of DVP-SS2 is DC. When operating DVP-SS2, please note the

following points:

1. The power is connected to two terminals, 24VDC and 0V, and the range of power is

20.4 ~ 28.8VDC. If the power voltage is less than 20.4VDC, the PLC will stop running,

all outputs will go “Off”, and the ERROR indicator will start to blink continuously.

2. The power shutdown for less than 10ms will not affect the operation of the PLC.

However, the shutdown time that is too long or the drop of power voltage will stop the

operation of the PLC, and all outputs will go off. When the power returns to normal

- 4 -

status, the PLC will automatically resume the operation. (Please take care of the

latched auxiliary relays and registers inside the PLC when doing the programming).

Safety Wiring

Since DVP-SS2 is only compatible with DC power supply, Delta’s power supply modules

(DVPPS01/DVPPS02) are the suitable power supplies for DVP-SS2. We suggest you

install the protection circuit at the power supply terminal to protect DVPPS01 or

DVPPS02. See the figure below.

cAC power supply:100 ~ 240VAC, 50/60Hz dBreaker

eEmergency stop: This button cuts off the system power supply when accidental

emergency takes place.

fPower indicator gAC power supply load

hPower supply circuit protection fuse (2A) iDVPPS01/DVPPS02

jDC power supply output: 24VDC, 500mA kDVP-PLC (main processing unit)

lDigital I/O module

Input Point Wiring

There are 2 types of DC inputs, SINK and SOURCE. (See the example below. For

detailed point configuration, please refer to the specification of each model.)

DC Signal IN – SINK mode

Input point loop equivalent circuit

DC Signal IN – SOURCE mode

Input point loop equivalent circuit

24G

+24V

S/S

[ Figure 5 ]

+24V

24G

S/S

[ Figure 6 ]

Output Point Wiring

1. DVP-SS2 has two output modules on it, relay and transistor. Be aware of the

connection of shared terminals when wiring output terminals.

2. Output terminals, Y0, Y1, and Y2, of relay models use C0 common port; Y3, Y4, and

Y5 use C1 common port. See [Figure 7]. When the output points are enabled, their

corresponding indicators on the front panel will be on.

- 5 -

3. Output terminals, Y0 ~Y5 of transistor models use UP, ZP common port. See [Figure

8].

4. Isolation circuit: The optical coupler is used to isolate signals between the circuit

inside PLC and input modules.

Relay (R) output circuit wiring

cDC power supply dEmergency stop: Uses external switch

eFuse: Uses 5~10A fuse at the shared terminal of output contacts to protect the output circuit

fTransient voltage suppressor (SB360 3A 60V): Extends the life span of contact.

1. Diode suppression of DC load: Used when in smaller power [Figure 10a]

2. Diode + Zener suppression of DC load: Used when in larger power and frequent On/Off

[Figure 10b]

gIncandescent light (resistive load) hAC power supply

iManually exclusive output: For example, Y3 and Y4 control the forward running and reverse

running of the motor, forming an interlock for the external circuit, together with the PLC

internal program, to ensure safe protection in case of any unexpected errors.

jAbsorber: Reduces the interference on AC load [Figure 11]

Transistor (T) output circuit wiring

- 6 -

cDC power supply dEmergency stop eCircuit protection fuse

fThe output of the transistor model is “open collector”. If Y0/Y1 is set to pulse output, the

output current has to be bigger than 0.1A to ensure normal operation of the model.

1. Diode suppression: Used when in smaller power [Figure 13a]

2. Diode + Zener suppression: Used when in larger power and frequent On/Off [Figure 13b]

gManually exclusive output: For example, Y3 and Y4 control the forward running and reverse

running of the motor, forming an interlock for the external circuit, together with the PLC

internal program, to ensure safe protection in case of any unexpected errors.

RS-485 Wiring

Figure 14

D+ D- D+ D- D+ D-

1 2 2

cMaster node dSlave node

eTerminal resistor

Note: 1. Terminal resistors are suggested to be connected to master and the last slave with

resistor value of 120Ω.

2. To ensure communication quality, please apply double shielded twisted pair cable

(20AWG) for wiring.

Table des matières

Autres manuels Delta Electronics Contrôleurs

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-SC Manuel utilisateur

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-PLC Manuel utilisateur

Delta Electronics

Delta Electronics Programmable Logic Controller DVP06XA-H2 Manuel utilisateur

Delta Electronics

Delta Electronics DVP-ES2 Series Manuel utilisateur

Delta Electronics

Delta Electronics Position Control Module DVP01PU-H Manuel utilisateur

Delta Electronics

Delta Electronics AC Motor Drive VFD-G Manuel utilisateur

Delta Electronics

Delta Electronics Temperature Controller DTE Manuel utilisateur

Delta Electronics

Delta Electronics DTC1000 Series Manuel utilisateur

Delta Electronics

Delta Electronics Programmable Logic Controller DVP04AD-H2 Manuel utilisateur

Delta Electronics

Delta Electronics ASDA-A2 Series Manuel utilisateur

Delta Electronics

Delta Electronics AC Motor Drive VFD-EL Manuel utilisateur

Delta Electronics

Delta Electronics DVP-MC Series Manuel utilisateur

Delta Electronics

Delta Electronics Valve Temperature Controller DTV Manuel utilisateur

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-EC3 Manuel utilisateur

Delta Electronics

Delta Electronics Programmable Logic Controller DVP04DA-H2 Manuel utilisateur

Delta Electronics

Delta Electronics VFD-L Series Manuel utilisateur

Delta Electronics

Delta Electronics Programmable Logic Controller DVP28SV Manuel utilisateur

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-SS Manuel utilisateur

Delta Electronics

Delta Electronics AC Motor Drive VFD-VE Series Manuel utilisateur

Delta Electronics

Delta Electronics Program Copy Card TP-PCC01 Manuel utilisateur

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-SA Manuel utilisateur

Delta Electronics

Delta Electronics DVP-EH DIDO Manuel utilisateur

Delta Electronics

Delta Electronics AH500 Manuel utilisateur

Delta Electronics

Delta Electronics AH500 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur