Delphi Display Systems Endura 15X Manuel utilisateur

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 1 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

Title: Endura 15X OCS 15” Speaker Post Installation Instructions Doc Number: RDS-INS15XSSP

Revision: A

Department: Sales

Area:

Training

Approved and released Effective Date: 10/25/2016

Review Period: 365 days

Order Confirmation System (OCS)

Speaker Post Installation Instructions

Delphi Display Systems, Inc.

PROPRIETARY INFORMATION

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 2 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

This page intentionally left blank

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 3 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

Table of Contents

INTRODUCTION ............................................................................................................................................... 5

1.1

PEAKER

OST

OUNTING

PTION

................................................................................................................ 5

1.2

ECHNICAL

UPPORT

..................................................................................................................................... 5

REQUIRED TOOLS ........................................................................................................................................... 5

SITE PREPARATION ........................................................................................................................................ 6

3.1

ELECT

OCATION FOR THE

PEAKER

OST

................................................................................................... 6

3.2

ONDUITS

....................................................................................................................................................... 6

3.3

OOTING AND

NCHOR

OLTS

....................................................................................................................... 6

3.4

NCHOR

OLT

NSTALLATION

–

NSTALLATION

.................................................................................... 7

3.4.1

Retrofit of an Existing OCS ................................................................................................................... 7

3.5

UNNING THE

LECTRICAL

IRING

–

NSTALLATION

........................................................................... 8

3.6

UNNING THE

ATA AND

UDIO

ABLES

–

NSTALLATION

.................................................................. 8

MOUNTING THE SPEAKER POST ................................................................................................................ 8

4.1

LECTRICAL

ONNECTIONS

–

ONDUIT

OUNTED

UNCTION

............................................................. 11

4.2

LECTRICAL

ONNECTIONS

–

PEAKER

OST

OUNTED

UNCTION

.................................................... 11

4.3

IRCUIT

REAKER

ABELING

....................................................................................................................... 13

4.4

PEAKER

NSTALLATION

SING

EW OR

XISTING

LEMENTS

.................................................................... 13

4.5

ICROPHONE

NSTALLATION

SING

EW OR

XISTING

LEMENTS

............................................................. 13

4.6

ONNECTING THE

UDIO

ABLES

................................................................................................................ 13

OCS DISPLAY MODULE INSTALLATION ................................................................................................ 14

5.1

NSTALLING THE

OCS

ISPLAY

ODULE IN THE

PEAKER

OST

................................................................. 14

5.2

ONNECTING THE

ATA

ABLE

(

) ............................................................................................................... 16

5.3

ONNECTING THE

OWER

ABLE

................................................................................................................. 17

5.4

ECURING THE

ACK

ANEL

........................................................................................................................ 17

CABLE CONNECTIONS INSIDE THE STORE .......................................................................................... 17

CHANGE HISTORY ........................................................................................................................................ 18

APPENDIX A - FOOTING AND CONDUIT SPECIFICATIONS................................................................. 1

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 4 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

Table of Figures

IGURE

–

NCHOR

OLT

IT AND

EMPLATE

............................................................................................................. 6

IGURE

OMPLETED

OOTING

................................................................................................................................... 7

IGURE

OCK ON

ACK OF

PEAKER

OST

............................................................................................................... 8

IGURE

ETTING THE

OST

........................................................................................................................................ 9

IGURE

XAMPLE OF

SING

HIMS

......................................................................................................................... 10

IGURE

NSURE

OST IS

EVEL

............................................................................................................................... 10

IGURE

OWER

IPPLE FOR

LECTRICAL

ONNECTION

.................................................................................... 11

IGURE

NCOMING

LECTRICAL

OUTED

NTO

UNCTION

........................................................................ 12

IGURE

ONNECT

NCOMING

OWER PER LOCAL CODE AND

NEC .................................................................... 12

IGURE

ONNECTION

OMPLETE

UNCTION

EALED

............................................................................. 12

IGURE

XAMPLES OF

ROPERLY

ABELED

IRCUIT

REAKER

............................................................................ 13

IGURE

PEAKER

SSEMBLY

NSTALLATION

........................................................................................................ 13

IGURE

ETAIL OF

LIGNMENT

NGLE

TOP

....................................................................................................... 14

IGURE

NSERT

NDURA

15X

AT AN ANGLE

.......................................................................................................... 14

IGURE

NDURA

15X

NSERTED

NTO

HELF

....................................................................................................... 15

IGURE

TRAPS

NSERTED

TTACH

UTS TO

ECURE

...................................................................................... 15

IGURE

IGHTEN

#10

UTS WITH

5/16"

RIVER

................................................................................................... 16

IGURE

ATERTIGHT

ONNECTION

...................................................................................................................... 16

IGURE

NSERT

OWER

ONNECTOR

..................................................................................................................... 17

IGURE

ACK

ANEL

............................................................................................................................................ 17

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 5 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

1 Introduction

This document describes the installation procedure for the Delphi Order Confirmation System (OCS) Speaker Post

and is used in conjunction with other installation manuals which vary based on specific customer or system

requirements. This manual covers only preparation for and installation of the speaker post; which includes installing

the microphone, speaker and OCS into the post.

1.1 Speaker Post Mounting Option

The Speaker Post has been designed as a free standing integrated mounting system for the 9330 Series displays and

audio system speakers. The Speaker Post will accommodate a wide variety of speaker systems in either full or half

duplex configurations. The Speaker Post is constructed of aircraft quality aluminum 6061 and has been designed to

be aesthetically pleasing as well as durable and easy to install.

1.2 Technical Support

For technical assistance, please contact:

Delphi Display Systems, Inc.

3160 Pullman St.

Costa Mesa, CA 92626

Toll Free: (800) 456-0060

Email: tec[email protected]

2 Required Tools

The following is a list of required tools. Some tools may not be required for all installations.

 3/8" drive ratchet

 3/4" deep well socket

 3/4" open end wrench

 10" #2 Philips screwdriver

 5/16" nut driver

 3/8” nut driver

 Wire Strippers

 Portable soldering iron

 200' fish tape

 Cordless Drill/Driver

 Hammer

 Multi-Meter

 Hammer Drill - for use when installing new bolts in an existing concrete pad.

 Level

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 6 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

3 Site Preparation

This section describes the steps necessary to properly prepare the site for installation of the Delphi OCS Speaker

Post. Please read the entire section before beginning any work. The following items must be completed prior to

installation of the OCS Speaker Post.

3.1 Select Location for the Speaker Post

The OCS Speaker Post has been designed so that the display is positioned at the optimum height for most vehicles

when the bottom of the speaker post is level with the top of the curb near the vehicle. Refer to Appendix A when

selecting a location for distance specs. The speaker post must be placed in a position where the customer can see

both the OCS and the menu board clearly. If the speaker and microphone are to be installed in the speaker post, be

sure to select a position where an optimal audio condition can be maintained. Consider the underground vehicle

detector (loop) also. The center line position in front of the speaker post must be within 18” of the loop. If it is not,

a new loop may be necessary.

3.2 Conduits

A minimum of three (3) conduits must be run to the OCS Speaker Post; one for a dedicated electrical circuit, one for

audio cables and another for the data cables. Ensure that the conduits will be centered in the bolt pattern. Refer to

Appendix A for detailed specifications.

3.3 Footing and Anchor Bolts

Before pouring the footing, make sure that all of the conduit has been run and is in the correct locations. Locate the

anchor bolt mounting kit and verify the following contents shown in the figure below.

 Four (4) each ½” ‘J’ anchor bolts

 Eight (8) each ½” zinc plated hex nuts

 Eight (8) each ½” zinc plated flat washers

 One (1) each anchor bolt template

Figure 1 – Anchor Bolt Kit and Template

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 7 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

3.4 Anchor Bolt Installation – New Installation

Install the ½” anchor “J” bolts into the template and secure with the ½” nuts and washers. This will insure the

alignment of the mounting bolts in the concrete. Pour the concrete footing and locate the anchor bolts in the correct

position using the alignment tool. Make sure to keep the anchor bolt threads clean and finish the surface of the

concrete as smooth and level as possible. A properly installed footing, anchor bolts, and conduits should resemble

the one in the picture below.

Figure 2 - Completed Footing

3.4.1 Retrofit of an Existing OCS

In many retrofit installations, existing slabs may be used to mount the OCS Speaker Post. The footing must be at

least 12” wide by 12” deep and of sufficient depth to support the OCS Speaker Post. It may be necessary to remove

existing anchor bolts and install new ones to match up to the base plate mounting hole pattern. Verify that the

existing conduits will be centered within the bolt pattern.

Some installations may have conduits that have been run outside the existing speaker post. In these cases, conduit

can be run into the back of the speaker post utilizing the provided “knock outs”. If the “knock outs” are not in the

correct position to be used, you may cut your own “knock out” in the bottom of the back of the speaker post. DO

NOT PUNCH A HOLE AND EXTEND THE CONDUIT. You must cut the bottom edge of the post out. If you

do not, it will not be possible to remove the speaker post without first removing the conduit from the post.

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 8 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

3.5 Running the Electrical Wiring – New Installation

The OCS Speaker Post must be wired to a dedicated circuit on an isolated ground with the Point of Sale (POS)

system. Pull the electrical wiring in accordance with NEC and local building codes. Terminate the electrical wiring

with a standard single-gang junction box.

3.6 Running the Data and Audio Cables – New Installation

The data cable is provided by Delphi Display Systems and is pre-terminated on the OCS end with a weather proof

connector. Pull the data cable through the appropriate conduit starting at the OCS end. Leave five (5) feet of cable

protruding from the end of the conduit. This will allow enough cable to route up through the speaker post and

connect to the back of the display module. Do not under any circumstances leave any more than 5’ of data

cable inside of the speaker post.

4 Mounting the Speaker Post

Remove the back panel of the Speaker Post by using the supplied key to unlock the back panel.

Figure 3 - Lock on Back of Speaker Post

Lock on back of post.

Key located inside front of

Speaker Post in a plastic

bag tie strapped to the

mounting bracket

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 9 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

Install the speaker post over the bolts and conduits. Level the base plate and fasten with four (4) ½” nuts. If the

footing is not level, the base plate can be leveled using the supplied leveling shims around the bolts between the

speaker post and footing. After the speaker post is level, secure the bolts with the nuts provided.

Figure 4 - Setting the Post

Delphi Display Systems, Inc. RDS-INS15XSSP, Rev, A Page 10 of 19

Confidential Document:

Printed copies are Uncontrolled unless clearly marked as a Controlled document. User responsible for verifying document is the current revision.

Figure 5 - Example of Using Shims

Figure 6 - Ensure Post is Level

Table des matières

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur