Dell PowerEdge 2400 Manuel utilisateur



™









Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, notices, cautions, and warnings,

and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your

computer system.





  !"

"#

$%&$%&!"

"#

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer

Corporation is strictly forbidden.

Trademarks used in this text: Dell, PowerEdge, and the DELL logo are trademarks of Dell Computer

Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any

proprietary interest in trademarks and trade names other than its own.

Ocober 1999 P/N 8761T Rev. A01

Dell PowerEdge 2400 Systems — Installing Redundant Power Supplies 1-1







This document provides instructions on upgrading your Dell system with dual, redun-

dant hot-plug power supplies and a power-supply distribution board (PSDB).





 !!"



#$$%#&$'

'



()"*%++*#+



1. Remove the front bezel and both computer covers.

For instructions, see Chapter 7, Checking Inside the Computer,in the Installa-

tion and Troubleshooting Guide.

2. Disconnect the AC power cable from the AC power receptacle on the back of the

power supply.

3. Remove the two screws at the front edge of the top cover (see Figure 1-1).

1-2 Dell PowerEdge 2400 Systems —Installing Redundant Power Supplies



4. Slide the top cover about 2 centimeters (cm) (about half an inch) toward the front

of the computer and lift the cover away.

5. Disconnect the power cable harness from the POWER connector on the small

computer system interface (SCSI) backplane board, the POWER1 connector on

the system board, and the diskette drive and other drives in the external drive

bays.

When you disconnect a cable connector from the SCSI backplane board and the

system board, press the plastic latch on one side of the connector to release it.

6. Remove the two screws on either side of the power supply (see Figure 1-2).

To p c o ve r

Screws (2)

Dell PowerEdge 2400 Systems —Installing Redundant Power Supplies 1-3



7. Slide the power supply out of the system chassis.

8. Install the PSDB onto the PSDB tray (see Figure 1-3):

a. While holding the PSDB by its edges, position the PSDB so that the three

tabs on the PSDB tray fit through the corresponding slots in the PSDB and

the two power supply connectors face the back of the chassis.

b. Slide the PSDB toward the back of the system about 1 cm (a quarter of an

inch).

c. Secure the PSDB by tightening the thumbscrew.

Power-supply

mounting

screws (2)

Power

supply

1-4 Dell PowerEdge 2400 Systems —Installing Redundant Power Supplies

 !

9. Attach the 12-conductor cable labeled "PWR3" to connector P3 on the PSDB (see

Figure 1-4) and to connector POWER2 on the system board.

PSDB

Power supplies (2)

Catch on power supply handle

Dell PowerEdge 2400 Systems —Installing Redundant Power Supplies 1-5

" 

10. Attach the 24-conductor cable labeled "PWR1" to connector P1 on the PSDB and

connector POWER1 on the system board.

11. To attach the cable harness provided in the upgrade kit, perform the following

steps:

a. Attach the 18-pin connector labeled "PWR2" to connector P2 on the PSDB.

b. Attach the 16-pin connector to the connector labeled "POWER" on the SCSI

backplane board.

c. Connect the remaining connectors on the cable harness to the diskette

drive, tape drive, and other drives in the external drive bays.

12. Replace the top cover and secure it with the two screws.

13. Replace the two computer covers.



()"*),$,'

,$

1. Using your thumb and index finger, squeeze the catch in the middle of the power

supply handle (see Figure 1-3).

2. Rotate the handle downward.

()"*#-$,+,



3. Slide the power supply into the chassis (see Figure 1-3).

Power connector P2

Thumbscrew Power connector P3

Power Connector P1

1-6 Dell PowerEdge 2400 Systems —Installing Redundant Power Supplies

4. Rotate the power supply handle to the closed position (see Figure 1-3).

For better leverage, press against the upper corners of the handle.

NOTE: The power supply will not function until the handle is closed.

5. Repeat steps 1 through 4 to install the second power supply.

6. Connect the AC power cable to the power supplies and to the electrical outlet.

7. Make sure that the AC power cable passes through the plastic strain-relief clip on

the system back panel.

Autres manuels pour PowerEdge 2400

Table des matières

Autres manuels Dell Serveur

Dell

Dell PowerApp .cache 100 Manuel technique

Dell

Dell PowerEdge 500SC Manuel technique

Dell

Dell PowerEdge 2970 Manuel utilisateur

Dell

Dell PowerEdge C8000 Fiche technique

Dell

Dell EMC VxFlex Ready Node Manuel utilisateur

Dell

Dell PowerEdge 1955 Manuel utilisateur

Dell

Dell PowerEdge T310 Guide de démarrage rapide

Dell

Dell PowerEdge C6320 Manuel utilisateur

Dell

Dell VMware ESX Server 3i Manuel utilisateur

Dell

Dell PowerEdge 2600 Manuel technique

Dell

Dell PowerEdge M1000e Manuel utilisateur

Dell

Dell PowerEdge C6320 Manuel utilisateur

Dell

Dell PowerEdge 2410 Manuel utilisateur

Dell

Dell PowerEdge C8000 Manuel utilisateur

Dell

Dell PowerEdge R630 Manuel utilisateur

Dell

Dell PowerEdge R320 Manuel utilisateur

Dell

Dell PowerEdge NM176 Manuel utilisateur

Dell

Dell External OEMR R210II Manuel utilisateur

Dell

Dell PowerEdge T610 Manuel utilisateur

Dell

Dell PowerEdge C5230 Manuel utilisateur

Dell

Dell EMC DSS 9000R Manuel utilisateur

Dell

Dell PowerVault NX200 Manuel utilisateur

Dell

Dell PowerEdge C8000 Manuel utilisateur

Dell

Dell 6100 Instructions d'installation

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY BX900 Manuel utilisateur

Asus

Asus RS700DA-E6 PS4 Manuel utilisateur