Dell PowerEdge 1855 Manuel technique

www.dell.com | support.dell.com

Information Update

For instructions on installing your Dell

™

2342M Integrated Fibre Channel Module, refer to the

PowerEdge

™

1855

Installation and Troubleshooting Guide

. Configuration information, drivers, and

a list of EMC-approved software are available on

support.dell.com

Using the StorPort Driver with the Microsoft®Windows®

Server 2003 Operating System

If you are using the StorPort driver with the Microsoft

Windows Server 2003 operating system and

do not have Service Pack 1 or later installed, make sure you are using the latest

storport.sys

driver.

Updated StorPort drivers are available from

www.microsoft.com

. Refer to the EMC Support Matrix

(ESM) at

www.emc.com

for the latest required hotfix.

QLogic SANblade Manager Application

At present, the QLogic SANblade Manager application does not support the Dell 2342M

Integrated Fibre Channel Module daughter card for the PowerEdge 1855. When complete, drivers

will be available at

support.dell.com

If you need to implement Target Persistent Bindings, download the SANblade CLI available at

www.qlogic.com

in the EMC Approved Software section.

High Availability Clustering with Microsoft Cluster Server

High availability clustering with Microsoft Cluster Server (MSCS) is not supported. Support for

this feature is planned for Q1 2005.

Boot from SAN Option

Under certain SAN configurations, the

Hard Disk Drive Sequence

setting under

BIOS Setup

will

display as

Embedded

, followed by random ASCII characters. This truncated ASCII string

represents the external SCSI TARGET/LUN combination. Select this string to boot your system.

Despite this message, the Boot from SAN function works properly. A future version of the option

ROM (version 1.46 or later) for your fibre channel module will eliminate this issue. When

completed, this update will be available on

support.dell.com

November 2004

C8552am1.fm Page 1 Monday, November 22, 2004 1:08 PM

www.dell.com | support.dell.com

Brocade-based Switches May Cause Panic and Reboot

Fibre channel HBA paths may be dropped on hosts using the QLogic 7.00.03 Red Hat

Enterprise

Linux (version 3) driver and Brocade-based fibre channel switches running Brocade firmware

versions prior to 4.4.0 or prior to and including 3.2.0, depending on the switch model being used.

The workaround for this issue requires that you disable the FDMI feature in the QLogic 7.00.03

Red Hat Enterprise Linux (version 3) driver by recompiling the driver after performing the

following steps:

Contact Dell Technical Support to obtain the

patch_to_fix_mgmt_srv_unresolved_sym

driver patch.

qla_settings.h

, change

#define REG_FDMI_ENABLE 1

#define

REG_FDMI_ENABLE 0

Change to the directory where the QLogic 7.00.03 Red Hat Enterprise Linux (version 3)

driver source is located and apply the patch:

patch -p1 < patch_to_fix_mgmt_srv_unresolved_sym

Rebuild the driver as instructed in the

README.qla2x00

file.

___________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, PowerEdge, and the DELL logo are trademarks of Dell Inc.; EMC is the registered trademark

of EMC Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation; Red Hat is a registered

trademark of Red Hat, Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names

or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

C8552am1.fm Page 2 Monday, November 22, 2004 1:08 PM

Autres manuels pour PowerEdge 1855

Table des matières

Autres manuels Dell Serveur

Dell

Dell PowerEdge T20 Series Manuel utilisateur

Dell

Dell PowerEdge T20 Manuel du propriétaire

Dell

Dell PowerEdge M630 Manuel utilisateur

Dell

Dell POWEREDGE 4300 Mode d’emploi

Dell

Dell PowerEdge T100 Manuel utilisateur

Dell

Dell PowerEdge T20 Manuel utilisateur

Dell

Dell EMC VxFlex Ready Node 14G Manuel utilisateur

Dell

Dell PowerEdge B02S Manuel utilisateur

Dell

Dell PowerConnect W-AirWave 7.6 Manuel utilisateur

Dell

Dell EMC PowerEdge MX740c Manuel utilisateur

Dell

Dell PowerEdge SC1420 Manuel utilisateur

Dell

Dell PowerEdge Cluster SE500W Mode d’emploi

Dell

Dell PowerEdge T410 Manuel utilisateur

Dell

Dell PowerEdge M620 Manuel utilisateur

Dell

Dell PowerEdge T710 Manuel technique

Dell

Dell Wyse 5020 Manuel utilisateur

Dell

Dell PowerEdge 1750 Mode d’emploi

Dell

Dell DX6000 Manuel utilisateur

Dell

Dell POWEREDGE R515 Manuel utilisateur

Dell

Dell PowerEdge T130 Manuel utilisateur

Dell

Dell PowerEdge 600SC Manuel utilisateur

Dell

Dell PowerEdge XR8620t Manuel

Dell

Dell PowerEdge T620 Manuel utilisateur

Dell

Dell 6100 Manuel du propriétaire

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY BX900 Manuel utilisateur

Asus

Asus RS700DA-E6 PS4 Manuel utilisateur