Dell PowerEdge 1750 Manuel utilisateur

Autres manuels pour PowerEdge 1750

7

Table des matières

Autres manuels Dell Serveur

Dell

Dell PowerEdge 1500SC Manuel utilisateur

Dell

Dell DR4000 Restore Manager Manuel utilisateur

Dell

Dell Force10 C150 Manuel utilisateur

Dell

Dell PowerEdge 4600 Manuel utilisateur

Dell

Dell EMC PowerEdge XE7440 Manuel

Dell

Dell PowerEdge 6850 Manuel technique

Dell

Dell 8 Manuel technique

Dell

Dell PowerVault NX3500 Manuel utilisateur

Dell

Dell PowerEdge FC640 Manuel

Dell

Dell PowerEdge HS5610 Manuel

Dell

Dell EMC PowerEdge E75S Series Manuel

Dell

Dell PowerEdge R730xd Manuel utilisateur

Dell

Dell PowerConnect W-AirWave 7.6 Manuel utilisateur

Dell

Dell PowerEdge C410X Manuel utilisateur

Dell

Dell PowerEdge R430 Manuel utilisateur

Dell

Dell PowerEdge T610 Manuel utilisateur

Dell

Dell X95FF Manuel

Dell

Dell PowerEdge M820 Systems Manuel utilisateur

Dell

Dell EMC PowerEdge R350 Manuel

Dell

Dell PowerEdge T710 Manuel technique

Dell

Dell PowerEdge 400SC Manuel technique

Dell

Dell 8 Manuel technique

Dell

Dell PowerEdge E31S Series Manuel utilisateur

Dell

Dell PowerEdge R830 Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP

HP AlphaServer ES47 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY BX900 Manuel utilisateur

Asus

Asus RS700DA-E6 PS4 Manuel utilisateur

Dell Poweredge 1750

Installing a ROMB Card (PERC4/DI)

CAUTION: Before you perform this procedure, you must turn off the system and

disconnect it from its power source. For more information, see "Safety First—For

You and Your System" in "Troubleshooting Your System."

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your System

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

NOTICE: To avoid possible data loss, back up all data on the hard drives before changing

the mode of operation of the integrated SCSI controller from SCSI to RAID.

1. Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

2. Open the system covers. See "Opening the System Covers" in "Troubleshooting Your

System."

3. Locate the ROMB card connector on the system board. See Figure A-3.

4. If a PCI card is installed over the ROMB card connector, remove it. See "Removing an

Expansion Card."

5. Position the ROMB card with the notch in its plastic cover facing the redundant power

supply bay, and align the edges of the card with the four plastic standoffs on the

system board.

6. Press down on the three "bulls eyes" on the ROMB card cover until the four plastic

standoffs snap over the edge of the card. See Figure 6-11.

Figure 6-11. Installing the ROMB Card and Backup Battery

7. Install the ROMB backup battery:

a. Position the battery board as shown in Figure 6-11, and press it down into the

two standoffs until it snaps into place.

b. Plug the battery cable into the RAID BATTERY connector on the system board.

8. If you removed a PCI card in step 4, replace it. See "Installing an Expansion Card."

9. Close the system covers. See "Closing the System Covers" in "Troubleshooting Your

System."

10. Reconnect the system and peripherals to their power sources, and turn them on.

11. Enter the System Setup program and verify that the setting for the SCSI controller has

changed to reflect the presence of the RAID hardware. See "Using the System Setup

Program" in your User's Guide.

12. Install the RAID software. See the ROMB card software documentation for more

information.

Removing a ROMB Card

CAUTION: Before you perform this procedure, you must turn off the system and

disconnect it from its power source. For more information, see "Safety First—For

You and Your System" in "Troubleshooting Your System."

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your System

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

NOTICE: To avoid possible data loss, back up all data on the hard drives before changing

the mode of operation of the integrated SCSI controller from SCSI to RAID.

1. Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

2. Open the system covers. See "Opening the System Covers" in "Troubleshooting Your

System."

3. If a PCI card is installed over the ROMB card, remove the PCI card. See "Removing an

Expansion Card."

4. Pull the ROMB card up out of the four standoffs. See Figure 6-11.

5. Disconnect the ROMB backup battery from the backup battery connector, and pull the

battery assembly up out of the two standoffs. See Figure 6-11.

6. Close the system covers. See "Closing the System Covers" in "Troubleshooting Your

System."