Dell U3023E Manuel utilisateur
1
DELL U3023E
Unplug external cables(power cable and video
cable) from the monitor.
S2
Turn off power.
1. Disassembly Procedures:
S1
Remove stand from the product.(Press the stand
release button, lift the stand up and away from the
monitor)
S3
S4
Use a Philips-head screwdriver to remove 4pcs
screws for unlocking mechanisms. Remove DP caps.
(No.1~4 screw size=M4x11; Torque=11±1kgfxcm)
Tear off screen protector, then wedge your fingers
between rear cover and the middle bezel on the
corners of the top side of the monitor to release the
rear cover, then use one hand to press the middle
bezel, the other hand to pull up the rear cover in
order of arrow preference for unlocking the rear
cover.
S5
3
1
2
1
Lift the rear cover up carefully. Disconnect the
joystick key cable from the connector of the interface
board, and then remove the rear cover and put it
aside for later disassembling.
Use a Philips-head screwdriver to remove 2pcs
screw for unlocking the key board, then tear off the
tapes and release the key board.
(No.1~2 screw size=M2x3.3, Torque=0.8~1kgfxcm)
23
41
1
2
S6
S7
2DELL U3023E
S10
Use a Philips-head screwdriver to release one screw
for unlocking the USB board, and disconnect the two
USB cables and LED cable, then release the USB
board from the hooks of the middle bezel.
(No.1screw size=M3x5, Torque=4±0.5kgfxcm)
S11
S8
Tear off 2pcs aluminum foil for unfixing the two panel
lamp cables, and then tear off 2pcs acetate tapes for
uncovering the panel connectors, then disconnect
the panel lamp cables from the two connectors of
the panel module.
Use a Philips-head screwdriver to remove
16(11+5)pcs screws for unlocking the middle bezel
with the panel module.
(No.1~16 screw size=M3x5, Torque=5±0.5kgfxcm)
Tear off the tape on the back of panel module for
releasing the LED cable, then
middle bezel, and put it on a cushion foam, and then
tear off the mylar tape for releasing the LED board.
lift up and take away the
S12
U
.
se a Philips-head screwdriver to remove 4pcs
screws for unlocking the bracket chassis module
with the panel
(No.1~4 Screw size= M3x5, Torque=5±0.5kgfxcm)
4
1
11
1
3
12 14
13 15
9
2
11
4
576
1
16
810
S9
3
DELL U3023E
Use a Philips-head screwdriver to remove
screws for interface board and power board. Release
the panel lamp cable from the hook of the bracket.
8pcs
(No.1 screw size=M4x8, Torque=7±1kgfxcm;
No.2~8 screw size=M3x7.5, Torque=7±1kgfxcm)
S16
Remove the power board board and interface
board from the
disconnect all of the cables.
bracket chassis module carefully,
and then
Remove the Mylar tape from the hooks of the
bracket chassis module.
S15
S17
Move up the bracket, then push the earing-lock and
disconnect the LVDS cable away from the connectors
of the panel module.
Take away the bracket chassis module and then put
the bracket chassis module on a protective cushion.
1
3
4
2
68
75
S13
S14
4DELL U3023E
Remove electrolyte capacitors (red mark) from
printed circuit boards.
S18
S18-1 Cut the glue between bulk cap. and PCB with a knife.
S18-2 Ensure cutting path within the glue, don’t touch bulk
cap. or PCB.
S18-4 Take out bulk cap. pin solder with soldering iron and
absorber.
S18-5 Lift the bulk cap. up and away from the PCB.
S18-3 Cut into the bottom of bulk cap. and pullit up
carefully.
5
DELL U3023E
2. Product material information
The following substances, preparations, or components should be disposed of or recovered
separately from other WEEE in compliance with Article 4 of EU Council Directive
75/442/EEC.
3. Tools Required
List the type and size of the tools that would typically can be used to disassemble the
product to a point where components and materials requiring selective treatment can be
removed.
Tool Description:
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components No used
Batteries No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and
liquids
No used
Plastic containing BFR No used
Component and waste contain
asbestos
No used
CRT No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps No used
LCD display > 100 cm2 Product has an LCD greater than 100 cm2
External electric cable Product has external cables
Component contain refractory
ceramic fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors (height >
25mm, diameter > 25mm)
Ce manuel convient aux modèles suivants
1
Autres manuels Dell Moniteur
Dell
Dell E2015HV Manuel utilisateur
Dell
Dell UltraSharp 1909W AIO Manuel utilisateur
Dell
Dell P2222HB Instructions d'utilisation
Dell
Dell P2418HZ Manuel utilisateur
Dell
Dell SE2216H Manuel utilisateur
Dell
Dell UltraSharp 1908FP-BLK Manuel utilisateur
Dell
Dell IN2010N Manuel utilisateur
Dell
Dell S3222HG Manuel utilisateur
Dell
Dell UltraSharp 38 Manuel utilisateur
Dell
Dell S2319HS Manuel
Dell
Dell P Series Manuel d'utilisation et d'entretien
Dell
Dell S3222HN Manuel utilisateur
Dell
Dell W2600 Instructions d'utilisation
Dell
Dell UP2720QB Manuel utilisateur
Dell
Dell UltraSharp U3419W Manuel utilisateur
Dell
Dell E2011H Manuel utilisateur
Dell
Dell P2217 Manuel utilisateur
Dell
Dell UltraSharp U3818DW Manuel utilisateur
Dell
Dell P2421DCc Manuel utilisateur
Dell
Dell 2009WFP Manuel utilisateur
