Dell S2722DGM Instructions d'installation
Wedge your fingers between the rear cover and the
middle bezel on the corners of the top side of the
monitor to release the rear cover, then use one hand
to press the middle bezel, the other hand to pull up
carefully the rear cover in order of arrow preference
for unlocking mechanisms of rear cover.
Use a Philips-head screwdriver to remove four
screws for unlocking mechanisms.
(No.1~4 screw size=M4x8; Torque=10~11kgfxcm)
Take out all accessories including QSG, user’s
manual, labels(optinal), DP cable, HDMI cable,
power cable and other packing materials from the
carton.(Note: It depends on whether users returning
the accessories)
S2
Open the carton with a proper tool.
1. Disassembly Procedures:
S1
Take out the monitor from EPE-bag and put the LCD
monitor on a protective cushion.
23
41
Take out the base and molded pulp from the carton.
S3
S4
S6
S5
S7
base
4
3
2
3
1
1
DELL S2722DGM
Lift the rear cover up carefully. Disconnect the
function key cable and LED cable from the
connectors of the interface board, and then remove
the rear cover.
monitor
stand
HDMI cable
power cable
QSG
base
DP cable
User’s manual
labels(optinal)
S10
2DELL S2722DGM
S9
S11
Put the rear cover on a protective cushion. Tear off
the shading tape, then release the diffusion sheet
from the hook of the rear cover. Use a Philips-head
screwdriver to remove 4pcs screws for unlocking the
function key board with the rear cover. Tear off 2pcs
tapes for releasing the function key cable, then
release the function key board from the hook of the
rear cover.
(No.1~4 screw size=M2x0.2, Torque=0.8±0.2kgfxcm)
Tear off 2pcs tapes of the power cable. Use a Philips-
head screwdriver to remove 6pcs screws for
unlocking the middle bezel with the front bezel. Use a
Philips-head screwdriver to remove 13pcs screws for
unlocking the middle bezel with the panel module.
(No.1~6 Screw size=M2x3.3,Torque=3±0.5kgfxcm;
No.7~19 Screw size=M3x5, Torque=3~4kgfxcm)
S12
Tear off 1pcs aluminum foil for uncovering the LVDS
connector and cables, then tear off the tapes to
disconnect the panel cable away from the connector
of the panel module. Disconnect the power key cable
and touch key cable from the connectors of the
interface board.
1
3
4
2
Remove the middle bezel and put it into a fixture jip,
then tear off the tape for releasing the touch key
board away from the middle bezel. Tear off the black
PVC tape and use a Philips-head screwdriver to
remove 1pcs screw for unlocking the power key
board with the front bezel.
(No.1 Screw size= M2x2.4, Torque=0.8±0.2kgfxcm)
1
Remove the circuit boards from the
disconnect all
of the cables.
bracket
chassis module carefully, and then
S18
Use a Philips-head screwdriver to remove
screws for unlocking power board and interface
board, and then release the panel lamp cable from
the hook of the bracket.
6pcs
(No.1 screw size=M4x8, Torque=6±0.5kgfxcm;
No.2~7 screw size=M3x7.5, Torque=6±0.5kgfxcm)
S17
Turn over the bracket chassis module. Remove the
Mylar from the hooks of the bracket.
S16
3
DELL S2722DGM
Lift up the panel module and pull out the front bezel
for releasing the front bezel.
S15
S14
U
.
se a Philips-head screwdriver to remove 4pcs
screws for locking the bracket chassis module with
the panel
(No.1~4 Screw size= M3x0.5x2.8, Torque=5~6kgfxcm)
Move the bracket, and then disconnect the LVDS
cable from the connector of the panel module, then
lift up the bracket and put it on a protective cushion.
S13
3
4
2
1
56
4DELL S2722DGM
Remove electrolyte capacitors (red mark) from
printed circuit boards.
S19
S19-1 Cut the glue between bulk cap. and PCB with a knife.
S19-2 Ensure cutting path within the glue, don’t touch bulk
cap. or PCB.
S19-4 Take out bulk cap. pin solder with soldering iron and
absorber.
S19-5 Lift the bulk cap. up and away from the PCB.
S19-3 Cut into the bottom of bulk cap. and pullit up
carefully.
5
DELL S2722DGM
The following substances, preparations, or components should be disposed of or
recovered separately from other WEEE in compliance with Article 4 of EU Council
Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components
No used
Batteries
No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and
liquids
No used
Plastic containing BFR
No used
Component and waste contain
asbestos
No used
CRT
No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps
No used
LCD display > 100 cm2
Product has an LCD greater than 100 cm2
External electric cable
Product has external cables
Component contain refractory
ceramic fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors (height >
25mm, diameter > 25mm)
3. Tools Required
List the type and size of the tools that would typically can be used to disassemble the
product to a point where components and materials requiring selective treatment
can be removed.
Tool Description:
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
2. Product material information
Autres manuels pour S2722DGM
2
Autres manuels Dell Moniteur
Dell
Dell P6524QT Manuel utilisateur
Dell
Dell S2722DGM Manuel utilisateur
Dell
Dell G3223Q Manuel utilisateur
Dell
Dell P992 Manuel utilisateur
Dell
Dell 1701FP Manuel utilisateur
Dell
Dell E1709WFP Manuel utilisateur
Dell
Dell P1911 Manuel utilisateur
Dell
Dell SP190SFP Manuel utilisateur
Dell
Dell E193FPc Manuel utilisateur
Dell
Dell SE178WFP Manuel utilisateur
Dell
Dell P2419HB Manuel
Dell
Dell S2719DM Manuel utilisateur
Dell
Dell 2007FP - UltraSharp - 20.1" LCD Monitor Manuel utilisateur
Dell
Dell 1707FPV - UltraSharp - 17" LCD Monitor Manuel utilisateur
Dell
Dell E2016 Manuel utilisateur
Dell
Dell E Series Manuel utilisateur
Dell
Dell S2409WFP Manuel utilisateur
Dell
Dell P2418HT Instructions d'utilisation
Dell
Dell IN2030M Manuel utilisateur
Dell
Dell S199WFP - 19" LCD Monitor Instructions d'utilisation
