Dell P2222H Manuel utilisateur
Wedge your fingers between the rear cover and the
middle bezel on the corners of the top side of the
monitor to release the rear cover, then use one hand
to press the middle bezel, the other hand to pull up
carefully the rear cover in order of arrow preference
for unlocking mechanisms of rear cover..
Use a Philips-head screwdriver to remove four
screws for unlocking mechanisms.
(No.1~4 screw size=M4x10; Torque=12±0.5kgfxcm)
S6
Take out pack stand, base and all of the
QSG,
accessories
including DP cable, power cable, USB cable,
CD&user’s manualand EEI label(optinal) from the
carton.(Note: It depends on whether users returning
the accessories)
S2
Open the Pizza carton with a proper tool.
1. Disassembly Procedures:
Lift the rear cover up carefully. Disconnect the key
cable and USB FFC cable from the connectors of
the interface board, and then remove the rear cover.
S6
S5
S1
Take out of the Paper cushion from the carton, then
take out the packed monitor from the Pizza box and
put it on a cushion.
S3
Take out the monitor from the bag and put it on a
protective cushion.
S4
23
41
1DELL P2222H
1
3
22
QSG
monitor
stand
base
power cable user’s manual
DP cable
USB cable
Tear off 2pcs aluminium foils for unfixing the bracket.
Tear off 1pcs acetate tape, and then release the
panel lamp cable from the hook of the middle bezel.
S8
Disconnect the LED cable from the connector, then
release the LED cable by tearing off 2pcs tapes.
S9
Use a Philips-head screwdriver to remove 2pcs
screws for unlocking the joystick key board unit, then
tear off the tapes and release the USB board.
(No.1~2 screw size=M2x3.3,Torque=1±0.2kgfxcm)
S7
Use a Philips-head screwdriver to remove one screw
for unlocking the USB board unit, then release the
USB board unit and put it aside.
(No.1 screw size=M3x6, Torque=4±0.5kgfxcm)
2
DELL P2222H
S13
Take away the
.
middle bezel, and put it on a fixture,
then tear off the mylar tape for releasing the LED
board
S11
S12
Lift up the panel with the bracket for releasing the
front bezel away from the panel. Use a Philips-head
screwdriver to remove one screw for unlocking the
bracket with panel.
(No.1 screw size=M3x0.5x3, Torque=4±0.5kgfxcm)
12
1
Use a Philips-head screwdriver to remove 11pcs
screws for unlocking the middle bezel with the panel.
(No.1~9 screw size=M3x4, Torque=5±0.5kgfxcm;
)No.10~11 screw size=M1.6x1.7, Torque=1±0.2kgfxcm
S10
2
10
1
11
3
89
7
45
6
aluminum foil
conductive tape
1
Take away the bracket chassis module and then put
the bracket chassis module on a protective cushion.
S15
Remove the black Mylar from the hooks of the
bracket as the picture below shown.
Remove the interface board and power board from
the bracket chassis module carefully, and disconnect
all the cables.
Use a Philips-head screwdriver to remove 5pcs
screws for unlocking the power board and interface
board, and then release all the cables from the
hooks.
(No.1~4 screw size=M3x7.5, Torque=6±0.5kgfxcm;
No.5 screw size=M4x8, Torque=6±0.5kgfxcm)
S17
S14
S16
S18
Put the panel module on a protective cushion, then
disconnect the panel lamp cable from the connector
of panel module, then unplug the LVDS cable from
the connector of the panel module.
Use a Hex-head screwdriver to remove two screws
for unlocking the D-Sub connector.
(No.1~2 screws size=M3x8, Torque=6±0.5kgfxcm)
S19
3DELL P2222H
21
3
6
41
2
4
DELL P2222H
Remove electrolyte capacitors (red mark) from
printed circuit boards.
S20
S20-1 Cut the glue between bulk cap. and PCB with a knife.
S20-2 Ensure cutting path within the glue, don’t touch bulk
cap. or PCB.
S20-4 Take out bulk cap. pin solder with soldering iron and
absorber.
S20-5 Lift the bulk cap. up and away from the PCB.
S20-3 Cut into the bottom of bulk cap. and pullit up
carefully.
5DELL P2222H
The following substances, preparations, or components should be disposed of or
recovered separately from other WEEE in compliance with Article 4 of EU Council
Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components
No used
Batteries
No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and
liquids
No used
Plastic containing BFR
No used
Component and waste contain
asbestos
No used
CRT
No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps
No used
LCD display > 100 cm2
Product has an LCD greater than 100 cm2
External electric cable
Product has external cables
Component contain refractory
ceramic fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors (height >
25mm, diameter > 25mm)
3. Tools Required
List the type and size of the tools that would typically can be used to disassemble the
product to a point where components and materials requiring selective treatment
can be removed.
Tool Description:
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
2. Product material information
Autres manuels pour P2222H
3
Autres manuels Dell Moniteur
Dell
Dell E1910 - 19" LCD Monitor Manuel utilisateur
Dell
Dell UltraSharp U2412M Manuel de la liste des pièces
Dell
Dell E2016 Manuel utilisateur
Dell
Dell D7532QT Manuel utilisateur
Dell
Dell SE3223Q Manuel utilisateur
Dell
Dell S2418HN Manuel utilisateur
Dell
Dell S2319HS Manuel utilisateur
Dell
Dell E2423HN Manuel utilisateur
Dell
Dell E193FP Instructions d'utilisation
Dell
Dell U2312HM Manuel utilisateur
Dell
Dell P2217 Manuel utilisateur
Dell
Dell SE2422H Manuel utilisateur
Dell
Dell UltraSharp 1704FPV Manuel utilisateur
Dell
Dell S3423DWC Manuel utilisateur
Dell
Dell S2740L Manuel utilisateur
Dell
Dell G2410H Manuel utilisateur
Dell
Dell S2330MX Manuel utilisateur
Dell
Dell 2007FP - UltraSharp - 20.1" LCD Monitor Manuel utilisateur
Dell
Dell 2000FP Manuel utilisateur
Dell
Dell S3221QS Manuel utilisateur
