Dell 9200 Manuel utilisateur

Dell™Inspiron™9200ServiceManual 

Notes, Notices, and Cautions 
Abbreviations and Acronyms 
For a complete list of abbreviations and acronyms, see the Dell™Inspiron™Help file. To access the help file, see the Owner's Manual for your Dell computer. 
IfyoupurchasedaDell™nSeriescomputer,anyreferencesinthisdocumenttoMicrosoft®Windows®operating systems are not applicable. 
Information in this document is subject to change without notice. 
©2004DellInc.Allrightsreserved. 
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. 
Trademarks used in this text: Dell, the DELL logo, and Inspiron are trademarks of Dell Inc.; Microsoft and Windows are registered trademarks of Microsoft Corporation; Bluetooth is a 
trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. 
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own. 
Model PP14L 
December 2004 Rev. A01 
Before You Begin 

System Components 

Hard Drive 

Internal Card with Bluetooth®Wireless Technology 

Hinge Cover 

Memory Module, Modem, and Optical Device 

Keyboard 

Mini PCI Card 

Coin Cell Battery 

Palm Rest 

Display 
System Fans 

Video Card and Thermal Cooling Assembly 

Microprocessor Thermal-Cooling Assembly 

Microprocessor Module 

System Board 

USB Port Board 

Battery Latch Assembly 

Speakers 

Subwoofer 

Flashing the BIOS 

Pin Assignments for I/O Connectors 
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
 
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

Hard Drive

Dell™Inspiron™9200

Removing the Hard Drive

Replacing the Hard Drive

Returning a Hard Drive to Dell



Removing the Hard Drive



1. Follow the instructions in "Before Working Inside Your Computer."



2. Turn over the computer and remove the two M3 x 3-mm screws.



3. Slide the hard drive out of the computer.

Replacing the Hard Drive



1. Slide the drive into the bay until it is fully seated.



2. Replace and tighten the screws.



3. Reinstall Windows. For instructions, see "Reinstalling Microsoft®Windows®XP" in your Owner's Manual.



4. Reinstall Drivers. For instructions, see "Reinstalling Drivers and Utilities" in your Owner's Manual.

CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive.

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.

NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

NOTICE: To prevent data loss, turn off your computer before removing the hard drive. Do not remove the hard drive while the computer is on, in

standby mode, or in hibernate mode.

NOTICE: Hard drives are extremely fragile; even a slight bump can damage the drive.

NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell.

M3 x 3-mm screws (2)

hard drive

NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging. See "Protecting Against Electrostatic Discharge" in your

Owner's Manual.

NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector.

Returning a Hard Drive to Dell

Return your old hard drive to Dell in its original or comparable foam packaging. Otherwise, the hard drive may be damaged in transit.

Back to Contents Page



hard drive

foam packaging

Back to Contents Page

Video Card and Thermal Cooling Assembly

Dell™Inspiron™9200

Removing the Video Card and Thermal Cooling Assembly

Replacing the Video Card and Thermal Cooling Assembly

Removing the Video Card and Thermal Cooling Assembly



1. Follow the instructions in "Before Working Inside Your Computer."



1. Remove the hinge cover.



2. Remove the keyboard.



3. Remove the display assembly.



4. Remove the palm rest.



5. Loosen the four captive screws from the video card and thermal cooling assembly.



6. Gently pull up the video card and thermal cooling assembly from the system board.

Replacing the Video Card and Thermal Cooling Assembly



1. Carefully re-align the video card over the connector on the system board and press down.

CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTE: If you ordered a video card with your computer, it is already installed.

NOTE: The video card thermal cooling (heat sink) is part of the video card assembly.

system board connector

M2.5 x 6-mm screws (4)

video card/thermal cooling assembly

NOTE: The video card and thermal cooling assembly is labeled "PRESS HERE."



2. Tighten the four captive screws on the video card and thermal cooling assembly.

Back to Contents Page



Back to Contents Page

Microprocessor Thermal-Cooling Assembly

Dell™Inspiron™9200

Removing the Microprocessor Thermal-Cooling Assembly

Replacing the Microprocessor Thermal-Cooling Assembly

Removing the Microprocessor Thermal-Cooling Assembly



1. Follow the instructions in "Before Working Inside Your Computer."



2. Remove the hinge cover.



3. Remove the keyboard.



4. Remove the display assembly.



5. Remove the palm rest.



6. Loosen in consecutive order the four captive screws, labeled "1" through "4," that secure the microprocessor thermal-cooling assembly to the system

board.



7. Lift up the microprocessor thermal-cooling assembly and remove it from the system board.

Replacing the Microprocessor Thermal-Cooling Assembly



1. Evenly apply thermal grease to the top surface of the microprocessor.



2. Place the microprocessor thermal-cooling assembly over the microprocessor.



3. Tighten the four captive screws, labeled "1" through "4," in consecutive order.

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

microprocessor thermal-cooling assembly

captive screws (4)

Back to Contents Page



Back to Contents Page

Microprocessor Module

Dell™Inspiron™9200

Removing the Microprocessor Module

Replacing the Microprocessor Module

Removing the Microprocessor Module



1. Follow the instructions in "Before Working Inside Your Computer."



2. Remove the hinge cover.



3. Remove the keyboard.



4. Remove the display assembly.



5. Remove the palm rest.



6. Remove the microprocessor thermal-cooling assembly.



7. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE: Do not touch the processor die. Press and hold the microprocessor down on the substrate on which the die is mounted while turning the cam

screw to prevent intermittent contact between the cam screw and microprocessor.

NOTICE: To avoid damage to the microprocessor, hold the screwdriver so that it is perpendicular to the microprocessor when turning the cam screw.

NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

NOTICE: To ensure maximum cooling for the microprocessor, do not touch the heat transfer areas on the microprocessor thermal-cooling assembly. The

oils in your skin reduce the heat transfer capability of the thermal pads.

NOTICE: When removing the microprocessor module, pull the module straight up. Be careful not to bend the pins on the microprocessor module.

ZIF socket

screwdriver (perpendicular

to microprocessor)

ZIF-socket cam screw

pin-1 corner



8. Lift the microprocessor module from the ZIF socket.

Replacing the Microprocessor Module



1. Align the pin-1 corner of the microprocessor module with the pin-1 corner of the ZIF socket, and insert the microprocessor module.

When the microprocessor module is correctly seated, all four corners are aligned at the same height. If one or more corners of the module are higher

than the others, the module is not seated correctly.



2. Tighten the ZIF socket by turning the cam screw clockwise to secure the microprocessor module to the system board.



3. Perform the steps in "Removing the Microprocessor Module" in reverse order, beginning with step6.



4. Update the BIOS using a flash BIOS update program floppy disk or CD. For instructions on how to flash the BIOS, see "Flashing the BIOS."

Back to Contents Page



NOTE: The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw, which indicates

the direction to turn the cam screw.

NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in

the ZIF socket does not require force.

NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and

ZIF socket.

NOTE: The pin-1 corner of the microprocessor module has a triangle that aligns with the triangle on the pin-1 corner of the ZIF socket.

NOTICE: You must position the microprocessor module correctly in the ZIF socket to avoid permanent damage to the module and the socket.

Back to Contents Page

System Board

Dell™Inspiron™9200

Removing the System Board

Replacing the System Board

Removing the System Board



The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the bottom of the computer. The replacement kit for the

system board includes a CD that provides a utility for transferring the Service Tag to the replacement system board.



1. Follow the instructions in "Before Working Inside Your Computer."



2. Remove the hinge cover.



3. Remove the keyboard.



4. Remove the display assembly.



5. Remove the palm rest.



6. Remove the speaker connector from the system board.



7. Remove the USB connector from the system board.



8. Remove the hard drive bay connector from the system board.



9. If applicable, remove the video card.



CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.

NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.

USB connector

PC Card connector

bluetooth cable connector

speaker connector

NOTE: It is not necessary but highly recommended that you remove the system fans to allow easier access to the system board.

Autres manuels pour 9200

Table des matières

Autres manuels Dell Ordinateur portable

Dell

Dell Inspiron 7490 P115G Manuel utilisateur

Dell

Dell Vostro 3400 Manuel utilisateur

Dell

Dell Latitude 5490 Manuel utilisateur

Dell

Dell Precision Workstation M6400 Manuel utilisateur

Dell

Dell Dimension 5100 Manuel utilisateur

Dell

Dell Latitude XT3 Manuel utilisateur

Dell

Dell Inspirion 15-7568 Manuel utilisateur

Dell

Dell Latitude 2120 Manuel utilisateur

Dell

Dell Inspiron 14 5418 Manuel utilisateur

Dell

Dell Latitude 5400 Chrome Manuel

Dell

Dell 5530 Mono Laser Manuel utilisateur

Dell

Dell XPS 13 L321 Series Manuel utilisateur

Dell

Dell Inspiron 14 3482 Manuel d'exploitation et d'entretien

Dell

Dell Vostro 3405 Guide de l'utilisateur

Dell

Dell Inspiron 15 3535 Manuel utilisateur

Dell

Dell Vostro 5481 Manuel

Dell

Dell Latitude 5300 Manuel utilisateur

Dell

Dell Inspiron 9H825 Mode d’emploi

Dell

Dell Vostro 5480 Manuel utilisateur

Dell

Dell Precision 3510 Manuel utilisateur

Dell

Dell Inspiron 155000 Series Manuel d'exploitation et d'entretien

Dell

Dell LATITUDE D630 PP24L Manuel utilisateur

Dell

Dell Inspiron 15 3000 Series Manuel utilisateur

Dell

Dell P75F106 Manuel utilisateur

Manuels Ordinateur portable populaires d'autres marques

HP ze2401xt - Pavilion Notebook PC Manuel utilisateur

Velocity

Velocity NoteMagix M10 Manuel utilisateur

Toshiba

Toshiba A105-S2236 Manuel utilisateur

HP ENVY 17 Manuel

Winbook

Winbook LM Manuel utilisateur

HP PROBOOK 4520S Manuel

Sony

Sony VAIO PCG-FX270 Manuel utilisateur

Sony

Sony VAIO PCG-R505JLK Manuel utilisateur

Lenovo

Lenovo THINKPAD X32 Manuel utilisateur

HP Compaq tc4200 Guide de démarrage rapide

Toshiba

Toshiba mini NB300 Manuel utilisateur

Lenovo

Lenovo ThinkPad X201 Tablet Manuel

Lenovo

Lenovo THINKPAD X31 Manuel

Sony

Sony VGN-T240P VAIO Manuel utilisateur

Compaq

Compaq Armada E700 Series Manuel utilisateur

Fujitsu

Fujitsu Lifebook A6230 Manuel utilisateur

Acer

Acer Aspire ONE 722 Manuel utilisateur

Toshiba

Toshiba L300-EZ1524 Manuel utilisateur