Deif AL8-2 Manuel du propriétaire

DEIF A/

DEIF A/S Tel: (+45) 9614 9614

Frisenborgvej 33, DK-7800 Skive Fax: (+45) 9614 9615

Denmark E-mail: deif@deif.com

Programming manual

Alarm panel AL8-2

4189320003D

•

Compact Q96 design

•

Extremely easy push-button programming (no jumpers

or the like)

•

Individual programming of each input:

N/O or N/C, time delay, alarm inhibit, output

and cable supervision

•

Up to 5 units in master/slave configuration

•

Clear identification of first alarm received in case of

successive alarms

AL8-2 – Programming manual

4189320003D

Page 2/19

CONTENTS:

BEFORE YOU START PROGRAMMING ....................................................................3

THE PRINCIPLE OF PROGRAMMING........................................................................6

WHICH FUNCTIONS MAY BE PROGRAMMED? .......................................................7

HOW TO PROGRAMME INDIVIDUAL FUNCTIONS (INPUTS 1 TO 8).......................8

ALARM ON OPEN OR CLOSED SIGNAL CONTACT (N/C, N/O) .............................9

SELECTION OF OUTPUT RELAY (OUTPUT(S) AAND/OR OUTPUT B) .............. 10

INHIBIT OF INCOMING ALARM (INHIBIT) ............................................................. 10

ALARM ON CABLE FAILURE (CABLE FAILURE) .................................................. 11

TIME DELAYED REGISTRATION OF AN ALARM CONDITION (DELAY OF

ALARM) ..................................................................................................................11

SELECTION OF REQUESTED TIME DELAY (SET TIME) .....................................12

SELECTION OF BASIC TIME:..........................................................................13

SELECTION OF ADDITIONAL TIME:...............................................................14

PROGRAMMING OF COMMON FUNCTIONS ..........................................................15

SELECTION OF ACTIVATION/DEACTIVATION OF OUTPUT RELAY AON AN

ALARM CONDITION (N/O, N/C)............................................................................. 15

SELECTION OF TIME LIMITED ACTIVATION/DEACTIVATION OF OUTPUT

RELAY A................................................................................................................. 16

SELECTION OF ACTIVATION/DEACTIVATION OF OUTPUT RELAY BON AN

ALARM CONDITION (N/O, N/C)............................................................................. 17

SELECTION OF TIME LIMITED ACTIVATION/DEACTIVATION OF OUTPUT

RELAY B................................................................................................................. 17

DELAYED CANCELLATION OF INHIBIT FUNCTION (0..40 SECS).........................18

"MASTER"/"SLAVE" CONFIGURATION..................................................................19

AL8-2 – Programming manual

4189320003D

Page 3/19

On delivery, the AL8-2 alarm panel is programmed to the following functions:

Individual functions

•Alarm on closed signal contact (N/O)

•No activation of output relays A and B on an alarm condition

•Inhibit function NOT activated

•No alarm on cable failure

•Immediate registration of an alarm condition (i.e. time delay 0 sec.)

Common functions

•Output relays A and B activated on an alarm condition (N/O)

•Duration of activation is unlimited (i.e. time limit 0 sec.)

•No delay of cancellation of inhibit function (i.e. time delay 0 sec.)

BEFORE YOU START PROGRAMMING

Programming the DEIF alarm panel AL8-2 requires only few and simple preparations:

Firstly, auxiliary voltage should be connected (indicated by green light in the LED

marked "POWER ON").

CONNECTIONS

AL8-2 – Programming manual

4189320003D

Page 4/19

Secondly, the bezel and front sheet are removed to give access to the programming

front plate.

The descriptive text for alarm channels 1-8 and the output channels A and B is

written/set on the shown text label.

We recommend using "letter-press" to set the text (height: 2.7mm) or typing the text on

the label.

Please note that the horizontal lines at both sides of the label indicate lines to be

written on. Do not write between the lines.

AL8-2 – Programming manual

4189320003D

Page 5/19

ABC123

ABC123 ABC123

ABC123

CORRECT WRONG

The horizontal line at the top of the label indicates the left margin.

The text label is mounted behind the front sheet which has an adhesive rear. Label and

front sheet are easily separated and put together again, though.

NOTE: For marine applications, the front sheet is always to be glued in order to

prevent unauthorised personnel from changing the settings subsequently.

The arrows at the right side of the label indicate the connection of the individual alarm

channel to output relay(s) A and/or B, if any – see the arrows on the front sheet. Not

applicable arrows can be deleted using black ink.

NOTE: The LED indicating "POWER ON" according to the text on the front sheet

is the same LED which, on the programming front plate, is designated "DELAY

OF ALARM". The LED will of course continue being lit even though the front

sheet and the bezel are removed, provided that auxiliary voltage is connected

and the unit is in operation.

AL8-2 – Programming manual

4189320003D

Page 6/19

THE PRINCIPLE OF PROGRAMMING

Programming of the alarm panel is carried out by means of the 3 push-buttons

CHANNEL SELECT, FUNCTION SELECT and ENTER, positioned at the lower right

corner of the front plate.

The principle of programming is as follows:

"Point" to the requested channel (by means of CHANNEL SELECT); then "point" to the

requested function (by means of FUNCTION SELECT); finally select, i.e. enter, the

requested function (by means of ENTER).

The LEDs will, as described in the following,

indicate which channel/function is being

programmed at the moment. The

channels/functions are shown in a certain

order. The CHANNEL SELECTOR first points

to channel 1, repeated pressing of the push-

button enables stepping through the channels

1-2-3-4-5-6-7-8-1-2-3, etc. Likewise you step

through the various functions. The order of

these appears from the following pages of this

manual.

AL8-2 – Programming manual

4189320003D

Page 7/19

WHICH FUNCTIONS MAY BE PROGRAMMED?

It is possible to program 5 functions for each of the input channels 1 to 8.

Furthermore, programming of 4 common functions is possible.

The individual functions are as follows:

1) Registration of alarm on open or closed signal contact

- i.e. selection between N/C or N/O.

2) Activation of output(s) A and/or B on an alarm condition

- "OUTPUT A", "OUTPUT B"

3) Inhibit of incoming alarms

- "INHIBIT"

4) Detection and indication of cable failure

- "CABLE FAILURE"

5) Time delayed registration of an alarm condition.

The time delay "DELAY OF ALARM" can be set within the range 0..40 secs at intervals of 1

sec.

The common functions are as follows:

1) Activation/deactivation of relay for output A on an alarm condition

- (N/O, N/C)

2) Time limited activation/deactivation of output A.

The time limit can be set within the range 1..10 secs at intervals of 1 sec.

3) Activation/deactivation of relay for output B on an alarm condition

- (N/O, N/C)

4) Time limited activation/deactivation of output B.

The time limit can be set within the range 1..10 secs at intervals of 1 sec.

5) Delayed cancellation of inhibit function.

The delay can be set within the range 0..40 secs at intervals of 1 sec.

NOTE: When common functions are programmed, no channel is selected, only

functions. Individual functions may be programmed before common

functions or vice versa. The description of the programming of common

functions starts on page 15.

AL8-2 – Programming manual

4189320003D

Page 8/19

HOW TO PROGRAMME INDIVIDUAL FUNCTIONS (INPUTS 1 TO 8)

Set AL8-2 to programming status:

Press the PRG button. This button is slightly countersunk when

compared with the front plate, and a thin, sharp tool like e.g. a small

screwdriver, a needle or the like must be applied to press this button.

Do not use a pencil. The lead may break and fall behind the front plate.

After having pressed the PRG push-button, the LED below the push-

button will be lit (green), indicating that the alarm panel has been set to

the programming status and that programming may be started.

The LED for "DELAY OF ALARM" (i.e. "POWER ON") is switched off

when the unit is set to programming status.

The moment the "PRG" LED is lit (green), the LED for input channel 1 (INPUT 1)

is lit (green) to indicate that this channel may now be programmed.

When pressing the channel selector CHANNEL SELECT, the LED for channel 1 (INPUT

1) is switched off and the LED for channel 2 (INPUT 2) is lit (green), etc.

First step of the programming is thus to select input channel. When the requested input

channel is indicated, i.e. the relevant LED is lit (green), the FUNCTION SELECT push-

button is pressed.

NOTE: The LED for the selected input channel will continue being lit (green)

throughout the complete programming procedure for the relevant channel.

FUNCTION SELECT points to the individually programmable functions in the following

order:

1: N/O, N/C

2: OUTPUT A, OUTPUT B

3: INHIBIT

4: CABLE FAILURE

5: DELAY OF ALARM

I.e., after the first push of FUNCTION SELECT, N/O, N/C is selected.

AL8-2 – Programming manual

4189320003D

Page 9/19

ALARM ON OPEN OR CLOSED SIGNAL CONTACT (N/C, N/O)

The "N/O" and "N/C" LEDs indicate the actual function as follows:

NOTE: Both LEDs are lit simultaneously.

EITHER: GREEN N/O FUNCTION:

RED N/C Alarm on closed signal contact

OR: RED N/O FUNCTION:

GREEN N/C Alarm on open signal contact

By pressing the FUNCTION SELECT push-button, the LEDs switch from one indication

to the other – thus changing the function.

When the indication of the LEDs shows the requested function, this is entered into the

programme memory by pressing the ENTER push-button.

Pressing ENTER results in the next function in the order being automatically pointed to:

selection of output relay.

AL8-2 – Programming manual

4189320003D

Page 10/19

SELECTION OF OUTPUT RELAY (OUTPUT(S) A AND/OR OUTPUT B)

The LEDs for "OUTPUT A", "OUTPUT B" indicate the actual function as follows:

NOTE: Both LEDs are lit simultaneously.

EITHER: RED OUTPUT A FUNCTION:

RED OUTPUT B No output relays are

activated on alarm

OR: GREEN OUTPUT A FUNCTION:

RED OUTPUT B Output relay A is activated

on alarm

OR: RED OUTPUT A FUNCTION:

GREEN OUTPUT B Output relay B is activated

on alarm

OR: GREEN OUTPUT A FUNCTION:

GREEN OUTPUT B Both output relays A and B

are activated on alarm

Pressing the FUNCTION SELECT push-button will cause a change from the actual LED

indication/function to the next in the order, and so the FUNCTION SELECT push-button

is pressed, till the requested function is indicated by the LEDs. The requested function is

entered into the programme memory by pressing the ENTER push-button.

Pressing ENTER results in the next function in the order being automatically pointed to:

Inhibit function.

INHIBIT OF INCOMING ALARM (INHIBIT)

The "INHIBIT" LED indicates the actual function as follows:

EITHER: RED INHIBIT FUNCTION:

Inhibit function is NOT

active for this input

channel

OR: GREEN INHIBIT FUNCTION:

Inhibit function is active for

this input channel

Pressing FUNCTION SELECT causes a change from one

function to the other. When the required function is indicated,

enter this into the programme memory by pressing ENTER.

Pressing ENTER results in the next function in the order being

automatically pointed to: Alarm on cable failure.

Table des matières

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur