Definitive Technology ProCenter 1000 Manuel utilisateur

Please Inspect For Shipping Damage

Each loudspeaker leaves our plant in perfect condition. Any visible or concealed

damage most likely occurred in handling after it left our plant and should be

reported at once to your Deﬁnitive dealer or the shipping company which deliv-

ered your loudspeaker.

Congratulations

Congratulations on your purchase of the Deﬁnitive

Technology ProMonitor Loudspeaker System.

This revolutionary loudspeaker utilizes state-of-the-art

components (cast basket homopolymer-coned

bass-midrange drivers, moving coil ferroﬂuid-cooled

pure aluminum dome high frequency radiators, uniphase

crossover networks, etc.), a non-resonant PolyStone™

cabinet and low diffraction construction in order to

achieve the most lifelike sound possible in your listening

room for many years to come.

Your ProMonitor is a unique speaker which may be

used by itself as a full-range system or as a satellite

with a Deﬁnitive ProSub to create a three-piece system.

This three-piece system can then be combined with

the ProCenter as a four-piece home theater system

and then with two additional ProMonitors to create

acomplete Dolby Digital AC-3-ready ProCinema®

home theater system.

ProMonitor™800

ProMonitor™1000

Loudspeaker System

Owner’s Manual

It is critical for proper performance that both speakers (left and right) be connect-

ed in proper phase. Note that one terminal on each speaker (the +) is colored red and

the other (the -) is colored black. Please make certain that you connect the red (+)

terminal on each speaker to the red (+) terminal of its channel on your ampliﬁer or

receiver and the black (-) terminal to the black (-) terminal. It is essential that both

speakers be connected in the same way to the ampliﬁer (in phase). If you experience

agreat lack of bass, it is likely that one speaker is out of phase with the other.

Connecting Your Loudspeakers

Usually if distortion is heard when the speakers are being driven at

loud levels, it is caused by driving (turning up) the ampliﬁer too loud and

not driving the speakers with more power than they can handle. Remember,

most ampliﬁers put out their full rated power well before the volume control

is turned all the way up! (Often, turning the dial half way up is actually full

power.) If your speakers distort when you play them loud, turn down the

ampliﬁer or get a bigger one.

Using the ProMonitor

in Conjunction with a ProSub

When a pair of ProMonitors is used in conjunction with a ProSub, they may be

connected either directly to the left and right channels of your ampliﬁer or

receiver, or to the left and right speaker level outputs on a ProSub (when the

ProSub is connected via the high-level speaker wire inputs to the left and right

channel speaker outputs on your receiver). Connecting the ProMonitor to a ProSub

(which includes a built-in high-pass crossover for the ProMonitors) will result in

greater dynamic range (the system can be played louder without over driving the

satellites) and is recommended for most installations especially when the system is

being used for home theater. Because this is the most common set-up, the following

instructions relate to wiring the ProMonitors to a ProSub.

Wiring 2 ProMonitors and 1 ProSub

for Stereo (2-Channel) Use

1. First, wire the red (+) terminal of the left channel speaker wire output of your

receiver or ampliﬁer to the red (+) terminal of the left channel speaker wire (high

level) input of your ProSub.

2. Next, wire the black (-) terminal of the left channel speaker wire output of your

receiver or ampliﬁer to the black (-) terminal of the left channel speaker wire

(high level) input of the ProSub.

3. Repeat Steps 1 and 2 for the right channel.

4. Wire the red (+) terminal of the left ProMonitor to the left channel red (+)

speaker wire (high level) out on the back of the ProSub.

5. Wire the black (-) terminal of the left ProMonitor to the left channel black (-)

speaker wire (high level) out on the back of the ProSub.

6. Repeat steps 4 & 5 for the right ProMonitor.

7. Set the low frequency ﬁlter control on the back of the ProSub to the setting described

in a ProSub Owner’s Manual. Please note that the exact frequency will depend on

many factors including speciﬁc positions of the speakers in the room, so you might

experiment with a slightly higher or lower setting to achieve ideal blending between

the sub and the satellites for your particular set-up. Listen to a wide variety of music

to determine the correct setting for this in your system.

8. Set the subwoofer level control to the setting described in a ProSub Owner’s Manual.

Please note that the exact level depends on many factors including your room size,

position of the speakers, etc. as well as your personal listening taste, so you might

experiment with the subwoofer level while listening to a wide variety of music until

you achieve the ideal setting for your system.

9. If your receiver allows you to choose whether or not the main speakers are to receive

afull-range signal, choose full range (or “Large”Left and Right Main Speakers).

There are many different variations of the basic Dolby ProLogic and Dolby

Digital AC-3 formats and features, as well as a multiplicity of ways in which the

speakers can be hooked up to these systems. We will discuss the simplest and most

effective hookups and adjustments. If you have a particular question regarding your

set-up, please call us.

For Dolby ProLogic Systems

Follow Steps 1-9 provided earlier. The subwoofer will receive its low frequency

signal through the full-range speaker level outputs. If, however, your system has

aseparate subwoofer RCA low level output which has a remote control level

adjustment, you might also want to hook this up using an RCA-to-RCA low level

cable to the LFE/subwoofer-in low level input (the lower RCA input) on a ProSub.

Then use your remote control sub level adjustment to ﬁne-tune the low frequency

level for different types of program material. (You might ﬁnd you want a higher

level for some music or for movies).

For Dolby Digital AC-3 5.1 Systems

Please note that Dolby Digital decoders have bass management systems (systems

which direct the bass to the various channels) which vary from unit to unit.

Simplest Hook-Up

The simplest way to hook up and use your ProCinema System with Dolby Digital

5.1 Systems is to hook a ProMonitor to each of the front (main) left, front (main) right,

rear (surround) left and rear (surround) right channels and a ProCenter to the front

center channel outputs of your receiver or power ampliﬁer making sure that the red (+)

terminal of each speaker is hooked up to the red (+) terminal of its proper channel out-

put and the black (-) terminal is connected to the black (-) terminal of its proper chan-

nel output. Then connect the LFE RCA output on your receiver or decoder to the LFE

input on your Deﬁnitive ProSub subwoofer.

Using ProMonitors with a ProSub

in Home Theater

Set the bass management settings of your receiver or decoder (see your receiv-

er or decoder manual) for “Small”left front (main), right front (main), center

front, left rear (surround) and right rear (surround) to “Small,” and Subwoofer to

“Yes.” If your receiver/decoder allows you to choose the crossover frequency of

or between your subwoofer and satellites, choose the highest possible (up to 100

Hz for the ProMonitor 1000 and 120 Hz for the ProMonitor 800) Turn the low

pass ﬁlter control on the ProSub all the way up in a clockwise direction. Adjust

the relative levels of all ﬁve channels and the subwoofer according to the

channel balancing procedure outlined in your receiver or decoder manual.

THIS IS VERY CRITICAL.

Optional Hook-Up One

Hook up the left and right front ProMonitors and ProSub as described in Steps

1thru 9 earlier. Wire your center channel to the center channel out on your

receiver (or center channel ampliﬁer) and your left and right rear surround speak-

ers to the rear channel outputs on your receiver or rear channel ampliﬁer, taking

care that all speakers are in phase, i.e. red (+) to red (+) and black (-) to black (-).

Set the bass management system of your receiver or decoder for “Large”Left and

Right Main Speakers, “Small”Center and Rear Surround Speakers and “No”

Subwoofer. All the bass information including the .1 channel LFE signal will be

directed to the main left and right channels and into the subwoofer giving you all

the beneﬁts of Dolby Digital AC-3 5.1.

Optional Hook-Up Two

An option on this hook-up (if your decoder will allow you to select “Large”

Left and Right Main Speakers and “Yes”Subwoofer), in addition to the hook-up

as described above, is to use an RCA-to-RCA low level cable to connect the LFE

sub-out on your receiver to the low-level LFE/sub-in (the lower RCA input) on a

ProSub. Tell your bass management system that you have “Large”Left and Right

Main Speakers, “Small”Center and Surrounds, and “Yes”Subwoofer. You will

then be able to raise the LFE .1 channel level being fed to the subwoofer by either

using the LFE/sub remote level adjustment on your decoder (if it has one) or the

LFE .1 channel level control on your Dolby Digital channel balancing procedure.

This set-up has the advantage of allowing you to set the low frequency level on

the a ProSub for smooth balance with music while also allowing you to “juice

up the bass” for movies with the controls on your decoder. It should also sound

somewhat better.

Variation on the Optional Hook-up

One variation on the optional hook-up is to hook up and adjust the system as

described under “Optional Hook-Up” except select “Small”Left and Right Main

Speakers and “Yes”Subwoofer on the bass management system (along with

“Small”Center and “Small”Rear Surrounds). The advantage of this over the

Optional Hook-Up will be somewhat greater dynamic range (i.e., you can play

the system louder). However, depending on the speciﬁccharacteristics of the

crossovers designed into your bass management system, the transition and

blending between the satellites and subwoofer may not be quite as smooth and

continuous as the Optional Hook-Up, or with the basic hook-up detailed above

in Steps 1-9. However, if you wish to play the system louder, you can experiment

with this variation. In addition, this variation is also one which can be used if

your decoder bass management system does not allow a “Large”Left and

Right Main Speakers and “Yes”Subwoofer setting.

We encourage you to experiment with the various settings on your subwoofer,

settings on your decoder, and hook-up options as described until you ﬁnd the best

combination for you.

Using ProMonitors with a ProSub for Rear

Channel Surround Use

Since Dolby Digital is capable of delivering a full-range bass signal to the

rear channels, some more elaborate systems will include an additional ProSub

for the rear channels. In this case, simply wire the ProMonitors to the ProSub as

described in 1 thru 8 earlier, except wire to the rear surround outputs. Set the bass

management system for “Large”Rear Speakers.

Using ProMonitors with Separate Left and

Right Channel ProSubs

You may also use a separate ProSub for the Front Left and Front Right channels.

Simply follow all previous instructions except use only the left channel inputs and

outputs on the left ProSub and the right channel inputs and outputs on the right

ProSub.

It is important that some simple set-up recommendations be followed in order

to assure optimum performance in your room. Please remember that although these

recommendations are usually valid, all rooms and listening set-ups are somewhat

unique, so do not be afraid to experiment with the speakers. Remember, whatever

sounds best to you is correct.

The ProMonitor Loudspeakers may be placed on a stand or shelf or mounted on

the wall or ceiling. Placement close to the wall will increase the bass output while

placement further from the rear wall will decrease the bass output.

When used as fronts, the speakers should usually be placed 6 to 8 feet apart

and kept away from the side walls and corners. A good rule of thumb is to place

the speakers separated by one half the length of the wall they are positioned along,

and each speaker one quarter the length of the wall behind them away from the side

wall. When used as rear speakers, take care never to locate the speakers forward of

the listeners.

Speakers may be angled in towards the listening position or left parallel with

the rear wall according to your personal listening taste. Normally, angling the

speakers in so that they point directly at the listeners will result in more detail

and greater clarity.

Your ProMonitors should sound good right out of the box; however, an

extended break-in period of 20-40 hours or more of playing is required to reach

full performance capability. Break-in allows the suspensions to work in and results

in fuller bass, a more open “blossoming” midrange and smoother high frequency

reproduction.

Positioning the ProMonitor in Your Room

Speaker Break-In

The ProMonitors can be wall-mounted using the optional ProMount 80, which

should be available from your Deﬁnitive dealer. Your ProMonitor also has a built-in

keyhole wall-mount on the back. Use toggle bolts or other similar anchored fasten-

ers to fasten the ProMount 80 to the wall or to hold the keyhole mount. Do not use

an unanchored screw in the wall.

Please note that if you wall-mount the speaker, there is an optional plug included

which covers the hole in the bottom of the speaker which you will see after you

remove the built-in stand.

Wall Mounting the ProMonitors

It is our pleasure to offer assistance if you have any questions regarding your

ProMonitor or its set-up. Please contact your nearest Deﬁnitive Technology

dealer or contact us directly at 410-363-7148.

Service and warranty work on your Deﬁnitive loudspeakers will normally be per-

formed by your local Deﬁnitive Technology dealer. If, however, you wish to return

the speaker to us, please contact us ﬁrst, describing the problem and requesting

authorization as well as the locations of the nearest factory service center. Please

note that the address given in this booklet is the address of our ofﬁces

only.Under no circumstances should loudspeakers be shipped to our

ofﬁces or returned without contacting us ﬁrst and obtaining return

authorization.

Deﬁnitive Technology Ofﬁces

11433 Cronridge Drive, Suite K

Owings Mills, Maryland 21117

phone: 410-363-7148

Technical Assistance

Service

Visit us at www.deﬁnitivetech.com

and learn about all our exciting products.

ProMonitor 800 Speciﬁcations

Dimensions: 8

Weight: 4lbs. each

Frequency Response: 57 Hz – 30 kHz

Efﬁciency: 89 db

Nominal Impedance: 4 – 8 ohms

Driver Complement: One 4

"cast basket bass/midrange driver

coupled to a 4

"pressure-driven planar

low-frequency radiator. One 1" pure

aluminum dome tweeter.

Rec. Assoc. Ampl.: 10 – 150 watts/channel

ProMonitor 1000 Speciﬁcations

Dimensions: 10

Weight: 7lbs. each

Frequency Response: 47 Hz – 30 kHz

Efﬁciency: 90 db

Nominal Impedance: 4 – 8 ohms

Driver Complement: One 5

"cast basket bass/midrange driver

coupled to a 5

"pressure-driven planar

low-frequency radiator. One 1" pure

aluminum dome tweeter.

Rec. Assoc. Ampl.: 10 – 200 watts/channel

Speciﬁcations subject to change

Speciﬁcations

CTAT012909

This product complies with the essential requirements of

EMC directives 89/336/EEC and 73/23/EEC (inclusive of

93/68/EEC) and carries the CE mark accordingly.

Deﬁnitive Technology warrants to the original retail purchaser only that this Deﬁnitive

Technology Loudspeaker Product (the “Product”) will be free from defects in materials and

workmanship for a period of ﬁve (5) years covering the drivers and cabinets, and three (3) years

for the electronic components from the date of the original purchase from a Deﬁnitive

Technology Authorized Dealer. However, this warranty will automatically terminate prior to

the expiration of ﬁve (5) years for the drivers and cabinets and three (3) years for the electronic

components if the original retail purchaser sells or otherwise transfers the Product to any other

party. The original retail purchaser shall hereinafter be referred to as “you.” Defective Products

must be shipped, together with proof of date of purchase, prepaid insured to the Authorized

Dealer from whom you purchased the Product, or to the nearest factory service center.

Product(s) must be shipped in the original shipping container or its equivalent; in any case the

risk of loss or damage in transit is to be borne by you. If, upon examination at the Factory or a

Deﬁnitive Technology Authorized Dealer, it is determined that the unit was defective in

materials or workmanship at any time during this Warranty period, Deﬁnitive Technology or

the Deﬁnitive Technology Authorized Dealer will, at its option, repair or replace this Product at

no additional charge, except as set forth below. All replaced parts and Product(s) become the

property of Deﬁnitive Technology. Product(s) replaced or repaired under this Warranty will be

returned to you, within a reasonable time, freight collect.

This Warranty does not include service or parts to repair damage caused by accident, mis-

use, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage in

excess of the rated maximum of the unit, cosmetic appearance of cabinetry not directly

attributable to defects in materials or workmanship, or service, or repair or modiﬁcation of the

Product which has not been authorized by Deﬁnitive Technology. Deﬁnitive Technology makes

no Warranty with respect to its Products purchased from dealers or outlets other than

Deﬁnitive Technology Authorized Dealers. This Warranty is in lieu of all other expressed

Warranties. If this Product is defective in material or workmanship as warranted above, your

sole remedy shall be repair or replacement as provided above. In no event will Deﬁnitive

Technology be liable to you for any incidental or consequential damages arising out of the use

or inability to use the Product, even if Deﬁnitive Technology or a Deﬁnitive Technology

Authorized Dealer has been advised of the possibility of such damages, or for any claim by any

other party. Some states do not allow the exclusion or limitation of consequential damages, so

the above limitation may not apply to you.

All implied warranties on the Product are limited to the duration of this expressed

Warranty. Some states do not allow limitation on how long an implied Warranty lasts, so the

above limitations may not apply to you. This Warranty gives you speciﬁclegal rights, and you

also may have other rights which vary from state to state.

Limited Warranty:

5-Years for Drivers and Cabinets,

3-Years for Electronic Components

Autres manuels pour ProCenter 1000

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Definitive Technology Système de haut-parleurs

Definitive Technology

Definitive Technology Mythos Six Manuel utilisateur

Definitive Technology

Definitive Technology Mythos Gem XL Manuel utilisateur

Definitive Technology

Definitive Technology BPVX Manuel utilisateur

Definitive Technology

Definitive Technology StudioMonitor 350 Manuel utilisateur

Definitive Technology

Definitive Technology BP9080x Manuel utilisateur

Definitive Technology

Definitive Technology BP-3000 TL Manuel utilisateur

Definitive Technology

Definitive Technology ProCinema 60 Manuel utilisateur

Definitive Technology

Definitive Technology SuperCube III Manuel utilisateur

Definitive Technology

Definitive Technology Mythos One Manuel utilisateur

Definitive Technology

Definitive Technology W Studio Micro Manuel utilisateur

Definitive Technology

Definitive Technology C/L/R 2300 Manuel utilisateur

Definitive Technology

Definitive Technology ProSub 800 Manuel utilisateur

Definitive Technology

Definitive Technology ProCinema 600 Manuel utilisateur

Definitive Technology

Definitive Technology Mythos XTR Series Manuel utilisateur

Definitive Technology

Definitive Technology Mythos Gem Manuel utilisateur

Definitive Technology

Definitive Technology BPX Manuel utilisateur

Definitive Technology

Definitive Technology W Studio Micro Manuel utilisateur

Definitive Technology

Definitive Technology SuperCube II Manuel utilisateur

Definitive Technology

Definitive Technology BPVX Manuel utilisateur

Definitive Technology

Definitive Technology PC600 Manuel utilisateur

Definitive Technology

Definitive Technology ProCinema 400 System Manuel utilisateur

Definitive Technology

Definitive Technology BP 10B Manuel utilisateur

Definitive Technology

Definitive Technology BP1.2X Manuel utilisateur

Definitive Technology

Definitive Technology Mythos XTR 60 Manuel utilisateur

Manuels Système de haut-parleurs populaires d'autres marques

JVC

JVC CA-MXK5R Manuel utilisateur

LG NB4532B Manuel utilisateur

JVC

JVC CA-FSH100 Manuel utilisateur

5Core

5Core Pro Series Manuel utilisateur

EAW

EAW MQV1394e Manuel utilisateur

Lynx

Lynx GXR-LA10A Manuel utilisateur

iLive

iLive ITB066B Manuel utilisateur

RDX

RDX QuickStation 4 Manuel utilisateur

Electro-Voice

Electro-Voice S-122 Manuel utilisateur

Sven

Sven SPS-619 GOLD Manuel utilisateur

Pioneer

Pioneer CS-7070 Manuel utilisateur

EAW

EAW UB82e Manuel utilisateur

Sondpex

Sondpex Active Speaker System and Digital Music... Manuel utilisateur

JVC

JVC NX-PN7 Manuel utilisateur

Marshall Amplification

Marshall Amplification AR-DM61-BT Manuel utilisateur

Yamaha

Yamaha NX-A01 - Speaker Sys Manuel utilisateur

SE Audiotechnik

SE Audiotechnik I-LINE Manuel utilisateur

Gemini

Gemini WRX-843 Series Manuel utilisateur