Defiant CD-5936-BK Manuel utilisateur

THANK YOU

We appreciate the trust and condence you have placed in Deant through the purchase of this motion security light.

We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of

products available for your home improvement needs. Thank you for choosing Deant!

USE AND CARE GUIDE

MOTION SECURITY LIGHT

Questions, problems, missing parts?

Before returning to the store, call Deant Customer Service

8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-866-308-3976

HOMEDEPOT.CA

Item #1000835261

1000817583

Model #CD-5936-BK

CD-5936-WH

Table of Contents

Table of Contents......................................2

Safety Information....................................2

Warranty ...................................................2

5-Year Limited Warranty ........................2

Pre-Installation.........................................3

Planning Installation ..............................3

Specications ........................................3

Tools Required .......................................3

Hardware Included.................................4

Package Contents..................................4

Installation................................................5

Operation...................................................7

Care and Cleaning ....................................9

Troubleshooting ......................................10

Safety Information

PRECAUTIONS

□Please read and understand this entire manual

before attempting to assemble, install, or operate

this light xture.

□This light xture requires a 120-Volt AC power

source.

□Some codes require installation by a qualied

electrician.

□This light xture must be properly grounded.

□This light xture should be installed outdoors to a

wall.

□The light xture should be mounted approximately

8 ft. (2.4 m) above the ground.

WARNING: Turn the power off at the circuit breaker or

fuse. Place tape over the circuit breaker switch and verify

power is off at the light xture.

NOTICE: Do not connect this light xture to a dimmer switch or

timer.

□This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

□CAN ICES-005 (B)/NMB-005 (B)

Warranty

5-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from date

of purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence, or

LEDs. Unauthorized service or modication of the product or of any furnished component will void this warranty in

its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use,

unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components

that a customer uses in conjunction with this product.

Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.ca.

3 Homedepot.ca

Please contact 1-866-308-3976 for further assistance.

Pre-Installation

PLANNING INSTALLATION

Before installing the light xture, ensure that all parts are present. Compare parts with the Hardware Included and

Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this

light xture.

Estimated installation time: 30 minutes

SPECIFICATIONS

Range Up to 40 ft. (12 m) (Varies with surrounding temperature)

Sensing angle Up to 180°

Electrical load - LED 15 Watts

Lumens 1100

Power requirements 120 VAC, 60 Hz

Time delay 10 seconds to 4 minutes

TOOLS REQUIRED

Phillips

screwdriver

1/8 in. Flathead

screwdriver

Wire strippers/

cutters

Circuit tester Work gloves Silicone

sealant

Ladder Safety goggles

Pre-Installation (continued)

HARDWARE INCLUDED

NOTE: Hardware shown to actual size.

AA BB CC

DD EE FF

Part Description Quantity

AA Mounting bracket screw 2

BB Mounting bracket screw 2

CC Decorative screw (pre-installed) 2

DD Mounting bolt 1

EE Wire connector 1

FF Mounting bracket (not to scale) 1

PACKAGE CONTENTS

Part Description Quantity

A Lamp head 2

B Light xture 1

C Motion sensor 1

D Mounting plate 1

5 Homedepot.ca

Please contact 1-866-308-3976 for further assistance.

Installation

1 Determining the mounting

location

NOTE: The light xture should be mounted approximately

8 ft. (2.4 m) above the ground.

□Determine the mounting location – wall mount

only.

□Position the lamp heads (A) in the general

direction of the desired light coverage.

Wall Mount

2 Removing the mounting plate

NOTE: This xture comes with a mounting plate (D). It is

pre-assembled on the light xture (B) for shipping.

□Unscrew the two decorative screws (CC)

connecting the light xture (B) to the mounting

plate (D) and remove the mounting plate (D)

using the pull loop.

3 Installing the mounting bracket

WARNING: Turn the power off at the circuit breaker or

fuse. Place tape over the circuit breaker switch and verify

power is off at the light xture.

NOTE: Four mounting bracket screws of various sizes are

included. The installation will only require two. Discard the

unused mounting bracket screws after installation.

□Remove the existing light xture.

□Install the mounting bracket (FF) using the

mounting bracket screws (AA or BB) that best

t the junction box.

□Firmly pull on the mounting bracket (FF) to

verify it is securely mounted to the junction

box. If necessary, use the screws that were

removed from the existing light xture.

AA or BB

Installation (continued)

4 Installing the mounting plate

NOTE: The center mounting plate (D) hole is for the

mounting bolt (DD). The other two holes in the mounting

plate (D) are for routing the house wiring.

NOTE: Ensure the “UP” arrow on the mounting plate (D)

is pointing up when attaching the mounting plate (D) to

the junction box.

□Connect the ground wire on the mounting

bracket (FF) to the house ground wire using a

wire connector (EE).

□Route the black and white junction box wires

through a hole in the mounting plate (D).

□Place the mounting plate (D) against the

junction box with the arrow pointing upward.

□Insert the mounting bolt (DD) through the

center mounting plate (D) hole and thread it

into the center hole of the mounting bracket

(FF). Tighten the bolt (DD) securely.

□Firmly pull on the mounting plate (D) to

verify it is securely attached to the mounting

bracket(FF).

NOTICE: When attaching this light to an external, surface mount

junction box (1), caulk the rear of the mounting plate (D) before

mounting.

5 Making the electrical

connections

□Insert the junction box wires into the side of

the terminal block. Tighten terminal block

screws and ground screw to secure the wires.

□Insert the white wire from the junction box

into the terminal marked “N (White)”.

□Insert the black wire from the junction box

into the terminal marked “L (Black)”.

Suitable for wet locations

Convient aux endroits humides

Idóneo para sitios húmedos

Wall mount only

Solo para montaje sobre pared

Installation murale seulement

Model:5936

Modèle:5936

Modelo:5936

Black

Noir

Negro

White

Blanc

Blanco

7 Homedepot.ca

Please contact 1-866-308-3976 for further assistance.

Installation (continued)

6 Mounting the light fixture

NOTICE: The two pins on the rear of the light xture must be

inserted into the terminal block for the light to work.

□Slide the light xture (B) onto the mounting

plate(D).

□Tighten the two decorative screws (CC)

securely. Do not overtighten.

NOTICE: When attaching this light to an external, surface mount

junction box (1), caulk around the inside of the light xture (B) before

attaching to the mounting plate (D).

7 Caulking around the light

fixture

□Caulk around the mounting plate (D) and

mounting surface with silicone sealant (not

included).

Operation

1 Adjusting the lamp heads

□Turn the power on at the circuit breaker or fuse

and turn on the wall switch.

□If needed, gently grasp the lamp heads (A) and

tilt or rotate them to adjust the light coverage

area.

Operation (continued)

2 Setting the sensor for testing

NOTE: When the “LUX” control is set to the “ + ” position,

the light xture will operate during the day or night. When

the “TIME” control is set to the “ – “ position, the light will

stay on for 10 seconds after all motion is stopped.

□Grasp the motion sensor (C) housing and rotate

right or left to access the controls.

□Set the “LUX” control to the “ + ” position.

□Set the “TIME” control to the “ – ”

position.

□Slide the “SENS” control to the “ – ”

position.

NOTE: The motion sensor will need to completely warm

up (60 seconds) before beginning the setup process.

–

LUX

+–

SENS

–

TIME

3 Adjusting the motion sensor

detection zone

□Perform a “walk test”: walk in an arc across

the front of the motion sensor (C).

□Watch the light. The light will come on

indicating motion has been detected.

□Stop, wait for the light to turn off, and then

begin walking again.

□Continue this process until the detection zone

has been established.

4 Adjusting the SENS control

□To increase the detection zone, turn the

“SENS” dial toward the “ + ” position.

□To decrease the detection zone, turn the

“SENS” dial toward the “ – ” position.

NOTE: The motion sensor (C) is more sensitive to motion

moving across the front of the sensor. The motion sensor

front of the sensor.

NOTE: The higher the “SENS” setting (sensitivity), the

greater the possibility of false triggering. To reduce false

triggering, turn the “SENS” dial toward the “ – ” setting.

LUX

+–

SENS

+–

TIME

9 Homedepot.ca

Please contact 1-866-308-3976 for further assistance.

Operation (continued)

5 Adjusting the TIME control

NOTE: The “TIME” control determines the amount of

time the light will stay on full bright after all motion has

stopped.

□Turn the “TIME” dial toward the “ + ” position

to increase the light on-time (up to 4 minutes).

□Turn the “TIME” dial toward the “ – ” position

to decrease the light on-time (10 seconds

minimum).

LUX

–

+–

SENS

+–

TIME

6 Adjusting the LUX control

NOTE: The “LUX” control determines how dark the

surrounding light level needs to be before the motion

sensor (C) will turn on the light when motion is detected.

□Turn the “LUX” dial toward the “ + ” position to

turn the light on when the surrounding light is

brighter (daytime).

□Turn the “LUX” dial toward the “ – ” position to

turn the light on when the surrounding light is

darker (nighttime).

LUX

–

+–

SENS

+–

TIME

7 Completing motion sensor

setup

□After all motion sensor (C) adjustments are

complete, rotate the motion sensor (C) so the

controls are facing the rear of the xture (B)

and the two dots are in alignment.

Care and Cleaning

□To prolong the original appearance, clean the light xture with clear water and a soft, damp cloth only.

□Do not use paints, solvents, or other chemicals on this light xture. They could cause a premature

deterioration of the nish. This is not a defect in the nish and will not be covered by the warranty.

□Do not spray the light xture with a hose or power washer.

Troubleshooting

Problem Possible Cause Solution

The light will not come on. □The light switch is turned off. □Turn the light switch on.

□The fuse is blown or the circuit breaker

is turned off.

□Replace the fuse or turn the

circuit breaker on.

□Daylight turn-off (photocell) is in effect. □Recheck after dark or turn

the “LUX” dial toward the

“ + ” position.

□The circuit wiring is incorrect (if this is

a new installation).

□Verify the wiring is correct.

□The outside air temperature is close to

the same as a person’s body heat.

□Increase the “SENS”

setting.

The light comes on during the

day.

□The motion sensor may be installed in a

relatively dark location.

□The light xture is operating

normally under these

circumstances.

□The “LUX” control is turned to the “ +”

position.

□Turn the “LUX” dial toward

the “ – ” position.

The light comes on for no

apparent reason.

□The motion sensor may be sensing

small animals or automobile trafc.

□Decrease the “SENS”

setting or reposition the

motion sensor.

□The “SENS” control is set too high. □Decrease the “SENS”

setting.

□The outside temperature is much

warmer or cooler than a person’s body

heat (summer or winter).

□Decrease the “SENS”

setting.

□The light xture is wired through a

dimmer or timer.

□Do not use a dimmer or

timer to control the light

xture. Replace the dimmer

or timer with a standard on/

off wall switch.

The lights stay on continuously. □The motion sensor may be picking up a

heat source, such as an air vent, dryer

vent, or brightly painted, heat-reective

surface.

□Decrease the “SENS”

setting or reposition the

motion sensor.

□The light xture is wired through a

dimmer or timer.

□Do not use a dimmer or

timer to control the light

xture. Replace the dimmer

or timer with a standard on/

off wall switch.

□The light xture is on the same circuit

as a motor, transformer, or uorescent

bulb.

□Install the light xture on

a circuit without motors,

transformers, or uorescent

bulbs.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Defiant Projecteur

Defiant

Defiant DFI-5892-WH Manuel utilisateur

Defiant

Defiant DFI-5408-GR Manuel utilisateur

Defiant

Defiant DFI-8852-BZ-G Manuel utilisateur

Defiant

Defiant MSH27920DLWD Manuel utilisateur

Defiant

Defiant CD-5928-WH Manuel utilisateur

Defiant

Defiant MSLED1801D Manuel utilisateur

Defiant

Defiant DFI-5851-BK Manuel utilisateur

Defiant

Defiant CD-5928-WH-A Manuel utilisateur

Defiant

Defiant DFI-5982-BZ Manuel utilisateur

Defiant

Defiant DFI-7004-WH-G Manuel utilisateur

Defiant

Defiant DFI-0654-WH Manuel utilisateur

Defiant

Defiant DF-5939-BK Manuel utilisateur

Defiant

Defiant DF-5416-BK-B Manuel utilisateur

Defiant

Defiant DF-5928-BZ-A Manuel utilisateur

Defiant

Defiant DFI-7005-WH-G Manuel utilisateur

Defiant

Defiant DFI-7148-BK Manuel utilisateur

Defiant

Defiant K40425002 Manuel utilisateur

Defiant

Defiant FSL2030LDF Manuel utilisateur

Defiant

Defiant 1002366429 Manuel utilisateur

Defiant

Defiant DFI-5983-BZ Manuel utilisateur

Defiant

Defiant DFI-0452-WH Manuel utilisateur

Defiant

Defiant DFI-0452-WH Manuel d'installation et d'exploitation

Defiant

Defiant DFI-7167-WH-G Manuel utilisateur

Defiant

Defiant DFI-0452-WH Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur