Dedrone Multi Sensor 2.5 Manuel utilisateur

Version 2.6 | IM-Inst-DT2536en ENGLISH

INSTALLATION

Manual

Multi Sensor 2.5

Dedrone

2 IM-Inst-DT2536en

Legal Provisions

The information contained in these documents is the property of Dedrone GmbH. Any

publication, whether in whole or in part, requires prior written approval by Dedrone GmbH.

Internal reproduction used solely for the purpose of product evaluation or other proper use is

allowed and does not require prior approval.

This manual is the intellectual property of Dedrone GmbH and is protected by copyright. All

rights reserved.

Dedrone GmbH

Miramstraße 87

34123 Kassel

Germany

Fon +49 561 861799-0

Fax +49 561 861799-111

Email info@dedrone.com

Dedrone

IM-Inst-DT2536en 3

Content

1Safety.......................................................................................................................................4

1.1 Symbols.............................................................................................................................................. 4

1.2 Intended Use..................................................................................................................................... 4

1.3 Safety Information .......................................................................................................................... 5

2The Multi Sensor ....................................................................................................................6

3Unpacking ............................................................................................................................... 7

4Scope of Delivery................................................................................................................... 7

5Installation..............................................................................................................................8

5.1 Select the Mounting Place............................................................................................................. 8

5.1.1 Mounting Location............................................................................................................... 8

5.1.2 Mounting Surface ................................................................................................................ 9

5.1.3 Mounting Orientation ......................................................................................................... 9

5.1.4 Power Supply, Cable Requirements and Required Tools .......................................... 10

5.1.5 Mounting Device ................................................................................................................. 11

5.2 Cable Preparation (Crimp) .............................................................................................................12

5.3 Installation with DT Wall Mount................................................................................................. 13

5.4 Installation with DT Pole Mount................................................................................................. 14

6Configuration....................................................................................................................... 15

6.1 Overview Ports Multi Sensor .......................................................................................................15

6.2 Overview Ports DroneTracker Server ........................................................................................15

6.3 Integrate Multi Sensor in Your Network and Login to DT Control Center .........................17

7Update ...................................................................................................................................19

7.1 Update Process .............................................................................................................................. 19

7.2 Update the DroneTracker Server with Internet Connection ............................................... 19

7.3 Update a DroneTracker System Offline....................................................................................20

7.4 Update Sensors ...............................................................................................................................21

7.5 Update Analytics Servers ..............................................................................................................21

8Shut Down the Multi Sensor..............................................................................................22

9Cleaning ................................................................................................................................22

10 Disposal .................................................................................................................................22

11 Technical Data......................................................................................................................23

12 Overview Sensor Installations ..........................................................................................25

1 Safety Dedrone

4 IM-Inst-DT2536en

1Safety

1.1 Symbols

Symbols Explanation

Indicates a situation which, if not avoided, can result in property damage

Information that is important for a specific goal, but is not safety-relevant

Indicates a requirement for meeting a specific goal

Desired result

A problem that might occur

Action to resolve a problem

1.2 Intended Use

The Multi Sensor is a network-attached multi-sensor system, which detects civil drones and

triggers an alarm. An alarm can be sent to the network and is shown in a user-interface.

The Multi Sensor is intended for civil commercial and private use. The Multi Sensor is not a

security camera to observe the ground.

The Multi Sensor is suitable for indoor and outdoor use.

Use this product only in accordance with the information provided in the enclosed

documentation and with the locally applicable legal standards and directives. Any other

application may cause personal injury or property damage.

Do not use the Multi Sensor for the fixed mount with the Accessories Mobile Kit.

Any use of the product other than that described in the intended use section does not qualify

as appropriate. The enclosed documentation is an integral part of this product. Keep the

documentation in a convenient place for future reference and observe all instructions

contained therein.

The type label must remain permanently attached to the product.

Dedrone 1 Safety

IM-Inst-DT2536en 5

1.3 Safety Information

Read, follow and retain all of the following safety instructions. Heed all warnings on the unit

and in the operating instructions before operation.



Warning! Setup should be carried out by trained personal only, in accordance with

the national electric code, ANSI/NSPA, and all local country codes.



Do not attempt to service this device yourself. Refer all servicing to qualified

service personnel. This device has no user-serviceable internal parts.

Whenever any damage to the device has occurred, unplug the devices from the

power source and refer servicing to qualified service personnel. Such damages can

be:

•the patch cable is damaged

•an object has fallen on the device

•the device has been dropped, or its enclosure has been damaged

•the device does not operate normally when the user follows the operating

instructions correctly



Adjust only those controls specified in the operating instructions. Improper

adjustment of other controls may cause damage to the unit.



Despite careful construction, electrical devices can cause fires. Do not mount the

Multi Sensor in areas containing highly flammable materials or gases. Do not

mount the Multi Sensor in a potentially explosive atmosphere.

Do not install product near any heat sources such as radiators, heaters, exhaust air

systems or other equipment (including amplifiers) that produce heat or ultrasonic

noise.

2 The Multi Sensor Dedrone

6 IM-Inst-DT2536en

2The Multi Sensor

The Multi Sensor is a network-attached multi-sensor system, which detects civil drones and

triggers an alarm. An alarm can be send to the network and is shown in the user-interface,

known as the DT Control Center.

Parts of the Multi Sensor

A Audio Sensor D Near Infrared HD Camera

B Multi Sensor E DT Mounting Plate

C HD Camera F DT Heat Sink

With the interacting sensors the Multi Sensor is able to detect all kind of civil drones. Based on

multiple parameters such as noise, shape, and movement patterns, the detection rate is

optimal. Depending on the environmental, weather conditions, drone type and drone size, the

detection rate varies significantly.

In case of a drone alert the built-in camera saves videos in HD quality and the audio sensor

saves the sounds, providing evidence of the threat intrusion.

B C D E

Dedrone 3 Unpacking

IM-Inst-DT2536en 7

3Unpacking

This equipment should be unpacked and handled with care. Check the exterior of the packaging

for visible damage. If an item appears to have been damaged in shipment, notify the shipper

immediately.

To pull the Multi Sensor out of the foam, spread the foam a bit with hands. There is no need to

use tools.

4Scope of Delivery

Verify that all the parts listed in the scope of delivery are included. If any items are missing,

notify your Dedrone Partner.

Do not use this product if any component appears to be damaged. Please contact Dedrone in

the event of damaged goods.

1 x Multi Sensor

1 x DT Wall Mount and DT Pole Mount

2 x Straps

1 x Bag with 2x screws Torx M5, 4x flat washer, 2x nuts

1 x Bag with 1x environmentally sealed Ethernet crimp connector, 1x RJ45 Plug

1 x Installation Manual

1 x Safety Information

The original packing carton is the safest container in which to transport the unit and must be

used if returning the unit for service. Save it for possible future use.

5 Installation Dedrone

8 IM-Inst-DT2536en

5Installation

5.1 Select the Mounting Place

5.1.1 Mounting Location

Select a secure installation location and mounting position for the device. Ideally, this is a

location where the device cannot be interfered with, either intentionally or accidentally.



Sonic and ultrasonic noise can disturb or disable the acoustic detection.

Mount the Multi Sensor as far away as possible from any source of noise, e.g.:

•Fans

•Radiators

•Converters

•Speakers

•Electrical motors

•Capping power supplies

•Trees (moving leaves producing ultrasonic noise)

Ensure that the location has the appropriate clearance from power and lightning conductors,

in accordance with NEC725 and NEC800 (CEC Rule 16-224 and CEC Section 60). Do not install

the device near the following object:

•Any excessive heat sources

•Any overhead power lines, power circuits, or electrical lights, or where there is a chance

of electrical discharge.



Note the properties of each Multi Sensor.This is needed for service and for correct

configuration. You can find all information on the type label on the backside of the

Multi Sensor.

We recommend to use the table in this manual (see chapter 12 Overview

Multi Sensor Installations, page 25). The following information is important:

•Serial Number

•MAC Address Video

•MAC Address Audio

•Type of Lens

•Position and Orientation

Dedrone 5 Installation

IM-Inst-DT2536en 9

5.1.2 Mounting Surface

Make sure the selected mounting surface is capable of supporting the combined weight of the

Multi Sensor and mounting hardware (sold separately) under all expected conditions of load,

vibration, and temperature.

5.1.3 Mounting Orientation

The Multi Sensor is designed for installation like the picture below, facing away from a vertical

surface. The maximum inclination is 28° to the vertical. Ensure that the rain and sun cover of

the camera is orientated above the camera.

Correct and incorrect mounting orientations

5 Installation Dedrone

10 IM-Inst-DT2536en

5.1.4 Power Supply, Cable Requirements and Required Tools

Power Supply

The Multi Sensor does not need any additional power supply connection. The power supply is

provided by the patch cable over active PoE+ (802.3at).

•Make sure, that your network has activated active PoE+ (802.3at).

•We recommend installing additional overvoltage protection between the sensor and the

switch.

Cable Requirements

Type Cat-6 Patch Cable

Recommendation: Cat-7 Patch Cable

Maximum Length 100 m (328 ft)

For longer distances a PoE extender is required

External Diameter 3.5 mm – 7.5 mm

For a weather resistant connection to the Multi Sensor, it is necessary to crimp the supplied

environmentally sealed Ethernet crimp connector to the patch cable (see 5.2 Cable Preparation

(Crimp), page 12).

Required Tools

•drilling machine

•screwdriver

•suitable screws for the underground

•depending on the mounting location a ladder or lift truck

•crimping tool. For an environmentally sealed connection to the Multi Sensor, it's necessary

to crimp the supplied connector to the patch cable.

•hex key: size 4 mm

•wrench: size 13 mm

Table des matières

Autres manuels Dedrone Capteur de sécurité

Dedrone

Dedrone RF-310 Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur