Datapath VSN Series Manuel utilisateur
Engineering the world’s best visual solutions
Quick Start Guide
VSNMicro 600
Each Datapath VSNMicro 600 is custom built to
order therefore the components, number and
type of inputs will dier from system to system.
Each VSNMicro 600 is shipped with a printed
diagram outlining the specic types of input(s)
and where they are located on the rear panel of
the system.
Any input cables supplied are clearly labelled
and will indicate which of the video input
connectors they relate to.
Thank you for purchasing the Datapath
VSNMicro 600 wall controller. The aim of
this document is to quickly guide you
through the process of initial setup.
For detailed information, the User
Guide can be downloaded from
www.datapath.co.uk
2
VSNMicro 600 Quick Start Guide
STEP 1 KEYBOARD AND MOUSE
Connect Keyboard and Mouse to USB Ports.
USB Ports are located on both the front and rear
panels of the system. It may be more convenient
to use the USB ports on the front for easy access.
6 x USB 3.0 ports on the rear panel
2 x USB 2.0 ports on the front panel
STEP 2 CONNECT TO A NETWORK OPTIONAL
If the VSNMicro 600 is to be used over a network, connect it to a network point
(cables not supplied) using one of the LAN connectors on the rear panel.
3
VSNMicro 600 Quick Start Guide
STEP 3 CONNECT INPUT SOURCE
As each VSNMicro 600 is custom built, the number and type of video inputs will
dier from system to system. If you have purchased an VSNMicro 600 with video
inputs, the input connectors are located on the rear panel as shown below.
The printed diagram shipped with the VSNMicro 600 shows the types of input
and connectors built into your specic system.
Connect the input sources to the relevant input connectors, cables may be
supplied for some inputs. See content list for details.
Input Connectors
4
VSNMicro 600 Quick Start Guide
If a control screen is unavailable, connect a single video wall display into the
Display Output 1 connector on the rear of the VSNMicro 600.
STEP 4 CONNECTING A CONTROL SCREEN
Your VSNMicro 600 is factory congured to use a control screen connected to the
system internal graphics device. Connect your control screen to one of the three
connectors on the motherboard panel on the rear of the VSNMicro 600. A control
screen is initially required to set up the system including the operating system
(Windows® 10).
Control Screen
Display Output 1
5
VSNMicro 600 Quick Start Guide
Ensure Power Supply Modules are correctly tted.
1
STEP 5 POWERING UP THE SYSTEM
If you have an ATX powered system, go straight to diagram 2 (Page 7).
For systems with an RPSU:
During transit, the Power Supply Modules are removed therefore you are
required to t them prior to using your VSNMicro 600. To t the Power Supply
Modules, remove all the packaging and carefully slide them into the power
supply unit on the rear of the system with the protective grill uppermost
(1). You will feel and hear a rm click when they are in place. For detailed
instructions on how to t the Power Supply Modules see the PDF User Guide
which can be found on the Documentation Media.
Never use force when inserting the Power Supply Modules as this can cause
damage not covered under the Datapath warranty.
6
VSNMicro 600 Quick Start Guide
Press the on/o button on the front of the VSNMicro 600 (3) to power up. There
will be a short delay followed by the sound of the internal fan. The fan noise will
subside when the system has fully booted.
Connect power (2) cables (single cable for ATX) then plug into and turn on the mains supply.
3
2
7
VSNMicro 600 Quick Start Guide
STEP 7 DISPLAY WALL CONFIGURATION
Once the Windows 10 setup is complete, the system will reboot and the
control screen will show a Windows desktop displaying the Display Driver
Conguration Tool (DDCT). The DDCT will guide you, step by step, through
the conguration of the graphics outputs, enabling you to quickly create one
or more video walls.
On the nal stage of the conguration, the DDCT will recommend the
optimum way to connect your VSNMicro 600 to your video wall displays.
A full description of the DDCT can be found in the User Guide located on the
Documentation Media.
STEP 6 WINDOWS 10 SETUP
Once the system has been built and congured in our factory the operating
system is resealed, therefore when switching the system on for the rst time,
the operating system setup commences. You will be prompted to enter
information to set up the Windows 10 operating system.
There is no requirement for users to activate Windows 10, activation is done
automatically. An internet connection is required to complete the automatic
activation.
You are strongly recommended to create a‘Restore USB Flash Drive’
(See Step 9).
8
VSNMicro 600 Quick Start Guide
It is recommended that you carefully read the instructions on each page of the
wizard. To commence your wall conguration, click on Start Wizard.
Select the type of displays being used on your wall:
Displays With Bezels – Monitors, TVs and DLP Cubes
Overlapable Displays – Projectors
LED Displays
Click on ‘Continue’.
The tool will then display a conguration page for the type of display you selected.
9
VSNMicro 600 Quick Start Guide
What Type of Displays do you Have?
Use the Manufacturer and Model dropdown lists to select the displays you
are using for your wall. If the wall consists of dierent displays, select each one
in turn to congure the type of display. The DDCT has an extensive database
of displays, however if your display is not contained in the list, you can input
the details manually by selecting Create Custom Display.
It is strongly recommended that measurements are taken from the display
manufacturer’s specications if available.
Add Displays
Add Displays is available for displays with bezels or overlapable displays. Use
the Displays Across and the Displays Up to create your Display Group.
Once created, congure the displays using What Type of Displays Do You
Have? When using overlapable displays Display Overlap becomes available,
enabling you to select a percentage of overlap between displays.
10
VSNMicro 600 Quick Start Guide
Autres manuels pour VSN Series
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Datapath Contrôleurs
Datapath
Datapath X4 Manuel utilisateur
Datapath
Datapath Fx4 Manuel utilisateur
Datapath
Datapath VSN870 Manuel utilisateur
Datapath
Datapath VSN400 Series Manuel utilisateur
Datapath
Datapath Aetria WallControl VSN Series Manuel utilisateur
Datapath
Datapath Fx4 Manuel utilisateur
Datapath
Datapath x Series Manuel utilisateur
Datapath
Datapath VSN450 Manuel utilisateur
Datapath
Datapath VSN 600 MICRO Manuel utilisateur
Datapath
Datapath iolite 600 Manuel utilisateur
Datapath
Datapath X4 Manuel utilisateur
Datapath
Datapath VSN400 Series Manuel utilisateur
Datapath
Datapath HX4 Manuel utilisateur
Datapath
Datapath Fx4/H Manuel utilisateur
Datapath
Datapath VSN Series Manuel utilisateur
Datapath
Datapath VSN Series Manuel utilisateur
Datapath
Datapath VSN V3 Manuel utilisateur
Datapath
Datapath VSN900 Series Manuel utilisateur
Datapath
Datapath VSN400 Series Manuel utilisateur
Datapath
Datapath iolite 12i Manuel utilisateur
