Daniamant W3-1 Manuel utilisateur

W3-1 Instruction –Issue 7 (D0685)

Description

The Dan W3-1 is a flashing lifejacket light which is activated by a water sensor

attached to the cable or manually using the on/off button.

Daniamant A/S

Industrivej 24C

DK-3550, Slangerup, Denmark

Tel: +45 47 37 38 00 Fax: +45 47 37 38 09

Email: [email protected]

www.daniamant.com

Dan W3-1 lifejacket light

Installation and Maintenance Instructions

Installation

The Dan W3-1 is for use on all types of lifejackets.

The Dan W3-1 is supplied with a fixing clip. The clip is intended to be placed

behind a strip of lifejacket material or reflective tape; the light is secured by

pressing it into the clip.

Light and fixing clip (part no.1950 for grey standard clip, for 1” webbing + part no. 1952

Clips 2, for 2” webbing) separated to show material path

It is the responsibility of the lifejacket manufacturer to ensure that the light is

attached securely and is in the correct position on the lifejacket to provide

maximum visibility when the wearer is in the water.

Operation

The DAN W3-1 is switched on automatically when the cable sensor is immersed

in water and can be switched off by pressing the on/off button.

The light can also be activated and deactivated manually by pressing the on/off

button.

The sensor on the cable can be tested by a metal clip.

Figure depicts the Manual ON/OFF Button

Cable

Sensor

p/n. 1950

p/n. 1952

Maintenance

Routine service

Dan W3-1 is maintenance free, but the following checks must be made annually:

1. Inspect the light for signs of damage or corrosion.

2. Press the on/off button and the light will commence flashing, then press

the button once more and the light should deactivate.

3. To test the Cable Sensor –a paper clip may be applied to the 2 water

contacts. It is recommended that the light is activated for 1 minute.

Replacement

The Dan W3-1 lifejacket lights have a storage life of 5 years and must be

replaced by the date shown on the label.

Health and safety information

Dan W3-1 lights contain Lithium cells. These must be handled correctly:

•Do not dismantle the light assembly

•Do not make any external electrical connection

•Do not recharge

•Do not incinerate

Store between -30°C and +65°C

The Batteries are hermetically sealed pressurised primary Lithium/Manganese

cells, and as supplied are electrically protected by a solid-state device and are

environmentally protected by a moulded plastic housing. In this condition the units

pose no definable hazard to health.

Information on the composition and behaviour of these products is contained in

the Product Safety Data Sheet, available from our website

(www.daniamant.com) or on request.

Disposal

Dispose of used and expired lights in accordance with local regulations. This

could be done through an approved environmental disposal agent.

Daniamant’s Survivor Location Lights contain batteries as well as electrical and

electronic components and must therefore be segregated from the domestic

waste stream and recycled. Disposing of this product correctly will help save

valuable resources and prevent any potential negative effects on human health

and the environment, which could otherwise arise from inappropriate waste

handling. Daniamant’s lights are marked with the symbol below which conveys

that this waste must be treated separately from household waste.

To ensure compliance with the WEEE and Battery Regulations, the Survivor

Location Lights placed on the market in the UK or Denmark should be returned to

Daniamant in the UK or Denmark, or deposited in your nearest WEEE Designated

Collection Facility, operated by your Local Authority.

Further copies of this installation and maintenance instructions are available to download from

our website www.daniamant.com

A copy of these instructions must be held with the ships/owners training manual.

Table des matières

Autres manuels Daniamant Éclairage marin

Daniamant

Daniamant Dan W3-2 Manuel utilisateur

Manuels Éclairage marin populaires d'autres marques

Francis Searchlights

Francis Searchlights FX560 Manuel utilisateur

Attwood

Attwood 5095 Manuel utilisateur

Glamox

Glamox aqua signal TX20 Series Manuel utilisateur

Attwood

Attwood 3100 Manuel utilisateur

Imtra

Imtra BCM California 60 Manuel utilisateur

Sealite

Sealite SL60 Supplément

Hella marine

Hella marine NAVILED PRO 2NM Manuel utilisateur

ACR Electronics

ACR Electronics 3940 Instructions d'installation

ETI Solid State Lighting

ETI Solid State Lighting 504081020 Manuel utilisateur

Sea gull lighting

Sea gull lighting Traverse Lyte Retrofit Kit Manuel utilisateur

Attwood

Attwood 3830 Manuel utilisateur

Sealite

Sealite SL-15 Supplément

Attwood

Attwood 911339 Manuel utilisateur

Sabik Marine

Sabik Marine carmanah 800 Series Manuel utilisateur

Attwood

Attwood 91041 Manuel utilisateur

Tranberg

Tranberg TEF 2438N Manuel utilisateur

Weems & Plath

Weems & Plath 700 Manuel utilisateur

Hella marine

Hella marine NaviLED 360 2LT 980 960-0 Series Manuel utilisateur