Danfoss NovoCon L Manuel utilisateur

AQ321852892717en-010301 | 1© Danfoss | 2021.09

NovoCon® L/XL

Operating Guide

NovoCon® L / SU / SD

AB-QM DN 125 - 150HF

NovoCon® XL

AB-QM DN 200 - 250HF

NovoCon® L / SU / SD NovoCon® XL

NovoCon® L/XL / 73690670

5-95 % RH

no condensing

MAINTENANCE

FREE

NovoCon® L NovoCon® XL

AQ321852892717en-0103012 | © Danfoss | 2021.09

NovoCon® L/XL

❶

③

2×

①

②

2×

④

12-15 Nm

2×

①

②

2×

③④

12-15 Nm

2×

❷

AUTO

13 mm 4 mm

AUTO

3,5 - 4,5 mm

× 0,7mm 4 mm T 10

①

②

③

3-5 Nm

2×

NovoCon® L

NovoCon® L/XL

NovoCon® L SU

⑤

⑥

3-5 Nm

2×

1×

②

①③

⑦

④

③

⑧

④

⑥

⑨

1×

②

①

⑤

⑦

3-5 Nm

2×

NovoCon® L SD

AQ321852892717en-0103014 | © Danfoss | 2021.09

NovoCon® L/XL

❸

⑨

①

②

AUTO

HN 10 5 mm

❹NovoCon® XL

NovoCon® XL

⑩

③

④

⑤

⑥

⑦⑧

⑪

⑫

⑬

⑭⑮

40 Nm

1×

HH10

3-5 Nm

2×

NovoCon® L/XL

❺

❻

MODE:

Normal

Calibration

Flush

De-Air

⑦

⑥

M16, M20 / MP16 1/2’’

M16

M20

M16

1/2’’

①

⑤

AUTO

3,5–4,5 mm ×

0,7 mm T 10

GND is common for all signals

②

③

④

0,7-1,1 Nm

2×

AQ321852892717en-0103016 | © Danfoss | 2021.09

NovoCon® L/XL

E100 VXX

281624

0030471

E100 VXX

281624

0030471

MADE IN SLOVENIA

NovoCon

003Z8560

Actuator for AB-QM DN125-150

Control signal: BACnet MS/TP, Modbus RTU, 0-10V, 0-20mA

6430 Nordborg, Denmark

Power: 24VAC/DC, 50/60 Hz, Operating 9.6 VA

Force: 2000N. Stroke: 50 mm. Speed: 3-24s/m. IP54/40, 10T55

III

E100 VXX

281624

0030471

Serial number and QR code can be removed from the

NovoCon® L/XL label and added to installation drawing.

Device Object

Instance Number

❼

DIP Switch

Dip switches for addressing and bus protocol selection are located under the lid of the actuator.

DIP Switches 1 to 7 are used to assign the MAC address manually. Default MAC address assignment

method is Auto MAC addressing for BACnet MS/TP and DIP Switches for Modbus RTU.

For termination of last unit on the field bus, turn DIP Switch 8 ON.

Dip switch 9 is not used.

Dip switch 10 is used to select between BACnet MS/TP (OFF=Default) and Modbus RTU (ON).

When the protocol is changed on DIP Switch 10, a power cycle is required.

❽

NovoCon® L

Application mode:

MSV:9 / 32810

Digital control (default),

Analog control

Select Valve Type

MSV:3 / 32802

(default AB-QM DN125)

Design Flow Rate

AV:30 / 32796 Heating

AV:31 / 32798 Cooling



Select application

MSV:10 / 32811

Heating (default)

Cooling



❾Initial configuration

NovoCon® XL

Application mode:

MSV:9 / 32810

Digital control (default),

Analog control

Select Valve Type

MSV:3 / 32802

(default AB-QM DN200)

Design Flow Rate

AV:30 / 32796 Heating

AV:31 / 32798 Cooling



Select application

MSV:10 / 32811

Heating (default)

Cooling



12345678910

OFF

Activate calibration

MSV:0 / 33284 state 2

or use manual calibration

Activate calibration

MSV:0 / 33284 state 2

or use manual calibration



NovoCon® L/XL

To avoid injury and damage to persons and devices, it is

absolutely necessary these instructions are carefully read

and observed prior to assembly and commissioning.

Necessaryassembly, start-up,andmaintenanceworkmust

be performed only by qualified, trained and authorised personnel.

Switch off the pump and the power line before mounting and wiring

the actuator.

Connect via safety isolating transformer.

Galvanic separations shall be provided for segments crossing

buildings.

Safety Note

❿

If the NovoCon® L/XL network is supplied with two or more AC

power boosters, caution must be observed when disconnecting

one of the transformers from the high voltage power line. As

the NovoCons may be connected in a daisy chain, there may be

high voltage on the primary side of the disconnected power supply.

Disconnect always both the primary and secondary side of the

transformer.

Safety Note

Firmware update

We recommend to validate the firmware version before installation.

The latest firmware can be downloaded at www.novocon.com by

selecting the tab: Support files.

73690670 / AQ321852892717en-0103018 | © Danfoss | DCS-S/SI | 2021.09

NovoCon® L/XL

ІМПОРТЕР:

UA: ТОВ з ІІ «Данфосс ТОВ», вул. Вікентія Хвойки, 15/15/6, м. Київ, 04080, Україна

Part Name Hazardous Substances Table

Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr(VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE)

Motor X O O O O O

O: Indicates that this hazardous substance contained in all of the homogeneous material for this part is below the limit requirement in GB/T 26572;

X: Indicates that this hazardous substance contained in at least one of the homogeneous material for this part is above the limit requirement in GB/T 26572;

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Danfoss Pompe à eau

Danfoss

Danfoss DDC20 Manuel utilisateur

Danfoss

Danfoss PAHT G Manuel utilisateur

Danfoss

Danfoss D1P130 Manuel utilisateur

Danfoss

Danfoss APP 1.0 Manuel utilisateur

Danfoss

Danfoss PAHT 256-308 Manuel utilisateur

Danfoss

Danfoss APP 11 Manuel utilisateur

Danfoss

Danfoss LPV Manuel

Danfoss

Danfoss KSV Series Manuel utilisateur

Danfoss

Danfoss H1 Series Manuel

Danfoss

Danfoss H1 Series Manuel

Danfoss

Danfoss APP W HC Series Manuel utilisateur

Danfoss

Danfoss D1 Series Manuel utilisateur

Danfoss

Danfoss APP series Manuel utilisateur

Danfoss

Danfoss Series 45 Manuel utilisateur

Danfoss

Danfoss RSA Series Manuel utilisateur

Danfoss

Danfoss H1 078 Manuel utilisateur

Danfoss

Danfoss 45 Frame K2 Series Manuel utilisateur

Danfoss

Danfoss 45 E Frame Series Manuel utilisateur

Danfoss

Danfoss APP 5.1 Manuel utilisateur

Danfoss

Danfoss H1P 078 Manuel

Danfoss

Danfoss APP S Series Manuel utilisateur

Danfoss

Danfoss ASV-P Manuel utilisateur

Danfoss

Danfoss APP 1.5 Manuel utilisateur

Danfoss

Danfoss PAH Series Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur