Danfoss ICAD 600A Manuel utilisateur

027R9801

Installation Guide

ICAD 600A/ICAD 1200A

Quick Start Guide

Note!

Cross tighten all

3 screws to ensure

equal tightening.

Max 3 Nm torque.

Grease

Terminal box -

not supplied

by Danfoss

Ref. Colour Description

A Black – Common Alarm

B Brown – ICM fully open

C Red – ICM fully closed

D Orange – GND ground

E Yellow + 0/4 – 20 mA Input

F Green + 0/2 – 10 V input or digital input

for on/oﬀ control

G Blue + 0/4 – 20 mA Output

I Black + Fail safe supply

Battery / UPS* 19 V DC

II White + Supply voltage

24 V DC

III Brown –

* Uninterruptable Power Supply

24 Volt DC

ON LY

Please observe cable voltage drop

Distance between the applied DC transformer

and the ICAD terminal box may cause

a voltage drop. Cross section of cables and

size of DC transformer must be calculated

so that the voltage at all time at the ICAD

terminal box*, both during standstill and

during operation of ICAD, is within this range:

Prefabricated ICAD cable

length Code number

1.5 m

027H0426

3 m

027H0438

10 m

027H0427

15 m

027H0435

Voltage ICAD terminal

(600A/1200A) [V DC]

Min. 21 22 23 24

Max. 26.4

* Do not measure inside the ICAD itself

24 Volt DC

ON LY

Quick Start Guide

Before you

start using ICAD:

Decrease

value

Edit /

Enter

Increase

value

Note:

If the keypad is not operated within

20 seconds; time out will automatically

exit programming mode.

Programming the ICAD

Valve label ID:

Valve size setup (mandatory)

Hold down for

2 seconds to enter

programming mode

; 01 ; 10

Press and

go to parameter 10.

Press

Press until

you reach 11 (password).

Press

Press until

you reach parameter 26

Press

11 ; 26

Press or

to select ICM size or CVE.

Press

ICM/CVE & ICAD

is now calibrating

0; 26 CA

Hold down for

2 seconds to exit

programming mode

1: ICM 20 with ICAD 600A

2: ICM 25 with ICAD 600A

3: ICM 32 with ICAD 600A

4: ICM 40 with ICAD 1200A

5: ICM 50 with ICAD 1200A

ICM 20 ICM 25-65 ICM 100-150

6: ICM 65 with ICAD 1200A

7: ICM 100 with ICAD 1200A

8: ICM 125 with ICAD 1200A

9: ICM 150 with ICAD 1200A

10: CVE pilot with ICAD 1200A

When powering up the ICAD, A1 will ﬂash in the display

NOTE !

If media temperature is lower than -30 °C (-22 °F) it is mandatory to set parameter i30 an i31.

See separate document attached in ICAD box: document number AN285243155312

Changing analogue input signal (optional)

; 01

; 03

Hold down for

2 seconds to enter

programming mode

; 03

Press until you

reach parameter 03.

Press

Press or

to select analogue

input signal

1: 0 – 20 mA

2: 4 – 20 mA*

3: 0 – 10 V

4: 2 – 10 V

2; 03

Press

* default factory setting

If A3 alarm occurs

the analogue input

signal is out of range

Hold down for

2 seconds to exit

programming mode

For further functions,

programming possibilities

and factory settings;

please see ICAD instruction.

24 Volt DC

O N LY

Factory reset of ICAD

Disconnect power 

Press down and 

simultaneously while

reconnecting power 

Release and 

Note:

If factory reset has been performed the

ICAD will start ﬂashing A1 in the display.

Autres manuels pour ICAD 600A

Ce manuel convient aux modèles suivants

Autres manuels Danfoss Électricité industrielle

Danfoss

Danfoss iSave 50 Manuel utilisateur

Danfoss

Danfoss iSave 50-70 Manuel utilisateur

Danfoss

Danfoss AK-SM 800A Manuel utilisateur

Danfoss

Danfoss ECL Comfort 210 Manuel d'instructions d'installation

Danfoss

Danfoss VACON OPTE3 Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 300 Mode d’emploi

Danfoss

Danfoss ECL Comfort A260 Manuel d'instructions d'installation

Danfoss

Danfoss CI 5 Series Manuel utilisateur

Danfoss

Danfoss AK-CC 210A Manuel utilisateur

Danfoss

Danfoss AK-CC55 Manuel utilisateur

Danfoss

Danfoss CI 6 Manuel utilisateur

Danfoss

Danfoss VLT 2800 Manuel utilisateur

Manuels Électricité industrielle populaires d'autres marques

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Manuel technique

Abtech

Abtech HVJB Series Mode d’emploi

Murata

Murata GRM0335C1H8R1DA01 Series Manuel utilisateur

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Manuel utilisateur

Eaton

Eaton Ulusoy HMH24-04 Manuel utilisateur

Newlong

Newlong NP-7H Manuel utilisateur

Murata

Murata GJM0335C1E4R4BB01 Series Manuel utilisateur

Stahl

Stahl 8575/12 Manuel utilisateur

SI Pegasus Manuel utilisateur

Murata

Murata GRM1555C1H2R7CA01 Seies Manuel utilisateur

Murata

Murata GRM0225C1E6R4BA03 Series Manuel utilisateur

Cooper Power Systems

Cooper Power Systems VXE15 Manuel utilisateur

S&C

S&C Vista SD Manuel utilisateur

Murata

Murata GRM0335C2A7R3CA01 Series Manuel utilisateur

Siemens

Siemens 3VA9988-0BM10 Manuel utilisateur

Siemens

Siemens SITRANS LVS100 Manuel utilisateur

Murata

Murata GRM32ER60G227ME05 Series Manuel utilisateur

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Manuel utilisateur