Danfoss G 4500 Manuel utilisateur

Installation Guide

How to apply Molycote G 4500 grease

for ICM motor operated valves

© Danfoss A/S (MWA), 2021-01 AN149686416719en-000401 | 1

027R9787

027R9787

Apply the molycote G4500 grease

(supplied with ICAD) to the O-ring

grove on the ICM adapter and

O-ring. Then install the greased

O-ring into the groove on the ICM

adapter as shown in the picture.

Apply another layer of grease over the O-ring

as shown in the picture.

Remove the O-ring on the ICM adapter with

your ﬁngers. Do not use any tool because it

could damage the O-ring.

For ICM in service

If there is any ice or moisture present,

it must be removed prior to applying

the grease. The ice can be melted with

an electric heater or hair dryer.

O-ring

Info for UK customers only:Danfoss Ltd. Oxford Road, UB9 4LH Denham, UK

2 | AN149686416719en-000401 © Danfoss A/S (MWA), 2021-01

Move down

to stop

Close ICM by turning the multi-function

tool counter-clockwise, until it cannot be

tightened further.

Open ICM by turning the multi-function tool

appox. 1 turn clockwise.

Install the ICAD actuator on the ICM adapter

making sure it is pushed completely down.

Fasten the set screws using a 2.5 mm hexagon

key

Set screws

For ICAD already electrical connected

to control system.

Program ICAD to manual mode.

(i01=2).

Install the ICAD actuator on the ICM

adapter making sure it is pushed

completely down. Fasten the set

screws using a 2.5 mm hexagon key.

Program ICAD to calibrate to the

actual ICM valve - i10 (password)

and i26 (selection of ICM size).

Await calibration to ﬁnish.

Return ICAD to normal operation.

(i01=1)

Table des matières

Autres manuels Danfoss Moteur

Danfoss

Danfoss H1B 160 cc Manuel utilisateur

Danfoss

Danfoss VLT OneGearDrive Manuel utilisateur

Danfoss

Danfoss TMT W FL Guide de configuration

Danfoss

Danfoss VLT OneGearDrive Manuel utilisateur

Danfoss

Danfoss VLT OneGearDrive Manuel utilisateur

Danfoss

Danfoss OMS Manuel utilisateur

Danfoss

Danfoss EM-PMI540-T3000 Manuel utilisateur

Danfoss

Danfoss MAH Series Manuel utilisateur

Danfoss

Danfoss EM-PMI540-T2000 Manuel utilisateur

Danfoss

Danfoss H1B060 Manuel utilisateur

Danfoss

Danfoss OMM EM Manuel utilisateur

Danfoss

Danfoss TMM 070 Manuel utilisateur

Danfoss

Danfoss VLT Brook Crompton Motor FCM 300 Mode d’emploi

Danfoss

Danfoss K Frame Series Manuel utilisateur

Danfoss

Danfoss Series 20 Guide de configuration

Danfoss

Danfoss 51 Series Manuel

Danfoss

Danfoss VLT AutomationDrive FC 300 Series Manuel utilisateur

Danfoss

Danfoss EM-PMI375-T200 Manuel utilisateur

Danfoss

Danfoss HG7 Manuel utilisateur

Danfoss

Danfoss VLT OneGearDrive ExtensionBox Manuel utilisateur

Danfoss

Danfoss EM-PMI540-T4000 Manuel utilisateur

Danfoss

Danfoss EM-PMI540-1500 Manuel utilisateur

Danfoss

Danfoss EM-PMI540-T4000 Manuel utilisateur

Danfoss

Danfoss H1B 060 Manuel utilisateur

Manuels Moteur populaires d'autres marques

Rotax

Rotax 125 senior MAX evo Manuel utilisateur

Kohler

Kohler K361 Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

Kohler

Kohler COMMAND CH18-745 Manuel utilisateur

Mercury

Mercury D4.2L D-Tronic Manuel utilisateur

Selve

Selve SE Plus-RC Series Manuel utilisateur

Perkins

Perkins 1206E-E66TA Manuel utilisateur

Skov

Skov DA 174 Manuel

Rossi

Rossi TX11 Series Manuel utilisateur

Siemens

Siemens SIMOTICS T-1FW3 Feuille d'instructions

AL-KO

AL-KO PRO 350 Manuel utilisateur

MTU

MTU 12 V 4000 Lx4 Manuel utilisateur

Nanni

Nanni N3.30 Manuel d'instructions

Nanni

Nanni N5.160 CR2 Manuel utilisateur

KSB

KSB SuPreme Series Instructions d'installation

Hiwin

Hiwin EM1 Series Manuel utilisateur

Rotax

Rotax 912 i series Mode d'emploi

Siemens

Siemens SIMOTICS XP 1MB1 Manuel utilisateur