Danfoss FT1244 Manuel utilisateur

Operator’s Manual

Danfoss FT1244

Crimp Machine

Danfoss FT1244 Crimp Machine Operator’s Manual

2 | © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. AQ439269330776en-000101

Table of Contents

Introduction ........................................................................................................................................ 3

Safety Instructions ............................................................................................................................. 3

Specifications ...................................................................................................................................... 3

Preoperation Procedures .................................................................................................................. 4

Installation ........................................................................................................................................... 4

Tooling .................................................................................................................................................. 4

Operating Instructions ...................................................................................................................5-9

Maintenance ........................................................................................................................................9

Machine Breakdown ...................................................................................................................10-11

Hydraulic Breakdown ..................................................................................................................12-13

Electrical Schematic ....................................................................................................................14-15

The calibration method for some early model crimp machines used fittings that are no longer supplied by Danfoss

Corporation.

Therefore, some of the data on the following pages may be considered obsolete, such as machine settings (i.e. 1401

socket data).

Calibration can still be performed using current (global) fittings. Please contact Danfoss for specific information.

Obsolate Data Notice

Danfoss FT1244 Crimp Machine Operator’s Manual

AQ439269330776en-000101 © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. | 3

The Danfoss FT1244 Crimp Machine is designed for the distributor or O.E.M. who needs production style crimping capacity. The FT1244 is a

hydraulically operated machine that will crimp Danfoss standard crimp fittings; -3 through -32*, including four spiral hose. The FT1244 will crimp

both straight and standard elbow fitting assemblies.

A compact hydraulic unit supplies pressure to a cylinder which provides the required crimping forces through the mechanical advantage of a

crimp ring and dies.

*Special fittings are required for -32 sizes. Refer to section “Procedure For Crimping -32 Hose Assemblies.”

Introduction

1. KEEP WORK AREA CLEAN.

Cluttered areas and benches

invite accidents.

2. AVOID DANGEROUS

ENVIRONMENT. Keep the

work area well lit. Do not

operate equipment when

floors are slippery. Always

ensure you have sound

footing with both feet on

the floor. Do not operate

controls if hands or controls

are wet.

3. PREVENT UNAUTHORIZED

OPERATION. Do not

permit anyone to operate

this machine unless they

have read and thoroughly

understand this manual.

Unplug the machine when

not in use.

4. USE THE RIGHT DIE CAGE.

Do not force the dies to

do a job they were not

designed for. Never mix dies

of different sets. Dies are

assembled in a cage.

5. WEAR PROPER APPAREL.

Do not wear loose clothing

or jewelry that could get

caught in moving parts.

Rubber-soled footwear is

recommended for best

footing.

6. DO NOT OVERREACH. Keep

proper footing and balance

at all times.

7. MAINTAIN DIES WITH

CARE. Dies used in the

FT1244 crimp machine are

hardened tool steel affording

the best combination of

strength and wear resistance

for long life. Hardened dies

are generally brittle and care

should be taken to avoid

any sharp impact. Never

strike a die with a hardened

instrument..

Safety Instructions

Specications

Dimensions 31 1/2” wide x 30” long x 42” high

Weight 425 lbs. without tooling

Electrical 115 volt, 1 phase, 60 Hz

Crimp Dies Eight per set

Max. Operating Pressure 4000 psi

Pump 2 3/4 gpm to 1000 psi

3/4 gpm to 4000 psi

Danfoss FT1244 Crimp Machine Operator’s Manual

4 | © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. AQ439269330776en-000101

Preoperation Procedures

CAUTION: THIS MACHINE IS TOP HEAVY!

Uncrate the FT1244 crimp machine and inspect the machine for possible shipping damage. The following components are in the tool box.

1 can of high efficiency PTFE grease (Danfoss part number FF91455)

1 Cone Locator Assembly

1 Hydraulic Unit Breather Cap

This machine is shipped completely plumbed and wired. The hydraulic unit reservoir has been filled with hydraulic oil.

Remove the pipe plug from the top of the reservoir and install the breather cap. Install the cone locator in the holder.

Installation

Install the machine on a solid floor capable of holding 425 pounds. Secure the machine to the floor with four 5/16” diameter fasteners

through the slots provided in the base. Position the motor switch (located on the front panel) in the stop position and plug in the cord.

The FT1244 crimp machine is wired for 115V, 60 Hz service and requires a 30 amp circuit breaker or fuse.

Tooling

Atooling set up consists of eight crimp dies and a fitting locator. The locator is used to locate the fitting in the machine. A cone shaped

locator is used when crimping straight fittings and a series of optional yoke locators is available for locating elbow fittings.

Do not attempt to operate the machine with less than eight (8) dies or intermix dies of different sets.

A die storage area is provided within the machine. Dies should be put away after use to avoid abrasive dust and dirt from sticking to the

friction surfaces and causing premature wear on dies or other machine components.

Danfoss FT1244 Crimp Machine Operator’s Manual

AQ439269330776en-000101 © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. | 5

Operating Instructions

HOSE PREPARATION

Select the proper hose and fitting style for the desired application. Some hose styles require the removal of a length of hose cover prior to

crimping. This is referred to as “Skiving.”

PROPER CRIMP DIE INSTALLATION

Remove the clear plastic guard.

Select the crimp dies specified in the PowerSource Crimp Spec Tool at danfoss.com/crimp for the selected hose style and size.

Liberally lubricate all sliding surfaces of the crimp dies with high efficiency PTFE grease (Danfoss part number T-400-G). Do not lubricate

the crimping surface of the dies. Also lubricate the crimp ring where the crimp dies slide.

Install the crimp dies by pulling the die release pins (Det. 18) and inserting the dies into the die slots from the outside as shown in

illustration 1. Make certain the angled surface on the dies is positioned as illustrated. Inserting crimp dies in any other position may result

in damage to the machine. Remove crimp dies in the opposite manner.

SETTING THE LOCATOR

STRAIGHT FITTINGS

The purpose of the locator is to properly position the fitting within the crimp dies area and to provide a positive back stop so no visual

alignment is required after initial set up. The cone shaped locator is used for locating all sizes of straight fittings.

Refer to illustration 1 for proper fitting location using the cone locator. Position the fitting and socket as shown (the 1/32” will move flush

with the end of the crimp die during the crimp cycle). Slide Det. 3 until Det. 1 seats into the fitting. Run nut (Det. 4) against Det. 3. It may

be necessary to adjust Det. 1 into Det. 3 for more clearance. Lock with Det. 2.

Illustration 1

Danfoss FT1244 Crimp Machine Operator’s Manual

6 | © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. AQ439269330776en-000101

ELBOW FITTINGS

(Optional tooling not supplied with the machine)

Elbow fittings may be crimped without a locator, but for quantity production, an elbow fitting locator kit (FT1204-150) is available. This kit

will accommodate elbow fittings through -20 size. (Visual alignment is necessary when crimping -24 and -32 sizes.)

The FT1204-150 kit consists of a yoke holder and yokes for tube sizes -4 through -16 (no yoke is required when crimping -20 size fittings). A

spacer is also included to provide the additional clearance required on some elbows.

Remove the cone locator and attach the yoke holder by tightening the set screw on the shoulder of Det. 3 (See illustration 2). Position the

fitting within the crimp dies as illustrated. Set up the assembly with the spacer inserted as shown. Slide Det. 3 forward as was instructed for

the cone locator and run nut (Det. 4) against the spacer. Crimp the fitting, pull out the spacer, push Det. 3 back against Det. 4 and remove

elbow..

Illustration 2

Danfoss FT1244 Crimp Machine Operator’s Manual

AQ439269330776en-000101 © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. | 7

SETTING THE MICROMETER FOR THE PROPER CRIMP DIAMETER

The micrometer is mounted to a tie rod of the crimp machine. With the correct micrometer setting, the machine will produce the desired

crimp diameter.

The crimp diameter specifications are listed in the PowerSource Crimp Spec Tool at danfoss.com/crimp for crimp spec details.

The exact micrometer settings may vary from one machine to another due to manufacturing tolerances. Furnished in the back of this

manual is a sheet of approximate micrometer settings for the first crimp. A calculation and a micrometer adjustment should establish

correct crimp diameter.

Example: Aeroquip 2681-12 hose requires a crimp diameter of 1.90-1.96. The recommended micrometer setting for set

up is .739. The micrometer was set to .739 and a sample fitting crimped. The crimp diameter obtained was

1.216. The nominal crimp diameter desired is 1.193. Subtracting 1.193 from 1.216, we conclude that our socket

is crimped .023 oversize. Each .001 change in crimp diameter requires a .004 change in micrometer setting.

Therefore, .023 x 4 = .092 change in micrometer setting. Add .092 to .739 to obtain a new setting of .831.

Crimp the same fitting again using the newly calculated micrometer setting. A crimp diameter between 1.190 and 1.196 should be

obtained. If further adjustment is necessary, the same procedure should be followed until the proper crimp diameter is obtained.

NOTE: Large size crimps will probably require more adjustment than smaller sizes.

When the correct micrometer setting is found, record it. The next time that style and size of hose is crimped, dial your recorded micrometer

setting and the first crimp should be good.

Danfoss FT1244 Crimp Machine Operator’s Manual

8 | © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. AQ439269330776en-000101

PROCEDURE FOR CRIMPING -32 HOSE ASSEMBLIES

Crimping -32 fittings requires special procedure to properly attach the fitting. The fitting used for this application is of one piece

construction (the socket is precrimped to the nipple to establish the required crimp length). Refer to the PowerSource Crimp Spec Tool at

danfoss.com/crimp for crimp spec details which outlines the required crimping information. Scribe a mark on the socket at the nipple end

at the desired dimension as indicated in the PowerSource Crimp Spec Tool at danfoss.com/crimp for crimp spec details. Locate the fitting

within the crimp die area (See illustration 3). Crimp the fitting as previously described.

HOSE

1509-32 .41

1529-32 .41

1546-32 .41

2661-32 .40

2665-32 .41

2681-32 .41

2766-32 .41

2777-32 .41

2781-32 .41

2791-.32 .35

FC194-32 .41

FC241-32 .41

FC299-32 .41

Illustration 3

Danfoss FT1244 Crimp Machine Operator’s Manual

AQ439269330776en-000101 © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. | 9

CRIMPING FIELD CRIMP STYLE HOSE ASSEMBLIES

Crimping field crimp style fittings requires special locating procedure. The fittings are located using the scribe lines on the socket of the

fitting (See illustration 4).

Maintenance

Normal maintenance of the FT1244 crimp machine requires a light film of oil coating over all the exposed black surfaces, crimp ring die,

contact surface lubricated with high efficiency PTFE grease (Danfoss part number T-400-G), and a maintained oil level within the hydraulic

power unit oil reservoir (one inch below the top of the reservoir).

Illustration 4

Danfoss FT1244 Crimp Machine Operator’s Manual

10 | © Danfoss FT1244 Crimp Machine Operator’s Manual | 2023.05. AQ439269330776en-000101

Machine Breakdown

Table des matières

Autres manuels Danfoss Outils de sertissage

Danfoss

Danfoss ET4040 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Danfoss

Danfoss Aeroquip ET3000 Manuel d'installation

Danfoss

Danfoss ET1280 Manuel utilisateur

Danfoss

Danfoss ET4400 Manuel utilisateur

Danfoss

Danfoss ET1187 Manuel utilisateur

Danfoss

Danfoss ET4000 Manuel utilisateur

Danfoss

Danfoss ET4300 Manuel utilisateur

Danfoss

Danfoss ET4350 Manuel utilisateur

Danfoss

Danfoss ET1000 Manuel utilisateur

Danfoss

Danfoss ET4500-002 Manuel utilisateur

Danfoss

Danfoss ET4001 Manuel utilisateur

Danfoss

Danfoss ET5025 Manuel utilisateur

Danfoss

Danfoss FT1330 Manuel utilisateur

Danfoss

Danfoss ET4100 Manuel utilisateur

Danfoss

Danfoss ET1187 Manuel utilisateur

Danfoss

Danfoss Aeroquip FT1380P Manuel utilisateur

Danfoss

Danfoss ET5070 Manuel utilisateur

Danfoss

Danfoss ET5020 Manuel utilisateur

Danfoss

Danfoss ET4500-001 Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2063528-1 Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur