Danfoss MCD LCP 501 Manuel utilisateur

Instructions: Control Panel LCP 501

MI.17.G1.02 - VLT is a registered Danfoss trademark

Instructions: MCD Control Panel LCP 501

Order Code: 175G0096

1. Description

The MCD 500 LCP can be mounted up to 3 metres away from the soft starter,

allowing remote control and monitoring. The LCP is rated IP65 when mounted

correctly in accordance with these instructions.

2. Packing List

1 x LCP 4 x M3 x 16 Screw

1 x Cable, DB9, 3 metres 4 x M3 Flat washer

1 x Gasket, foam 4 x M3 Spring washer

1 x Instruction sheet 4 x M3 Nut

2 x Jack screw

3. Specifications

Maximum cable length 3 metres

Protection IP65 and NEMA12

Instructions: Control Panel LCP 501

MI.17.G1.02 - VLT is a registered Danfoss trademark

4. Mounting the LCP

Models MCD5-0021 to MCD5-0105: The LCP can be removed or

replaced while the starter is running. It is not necessary to remove

mains or control voltage.

Models MCD5-0131 to MCD5-1600: The bus bar and/or heatsink are

live whenever mains voltage is connected. Remove mains and

control voltage from the soft starter before removing the cover.

1. Use the template to drill four mounting holes and two holes for the

DB9 connector.

2. Apply the foam gasket to the back of the LCP.

3. Align the LCP over the holes and screw in place.

177 HA614.10

4. Plug the cable into the LCP and the soft starter.

177 HA615.10

177 HA616.10

MCD5-0021 to MCD5-0105 MCD5-0131 to MCD5-1600

Instructions: Control Panel LCP 501

MI.17.G1.02 - VLT is a registered Danfoss trademark

5. Synchronising the LCP and the Starter

The DB9 cable can be connected/disconnected from the LCP while the starter

is running.

The first time a LCP is plugged into a starter, the

starter will copy its parameter settings to the LCP.

New Dis

Detected

If the LCP has previously been used with a MCD 500, the operator can select

whether to copy the parameters to the starter, or to copy the MCD 500's

parameter settings into the LCP.

Select the required option using the and

buttons. The selected option is surrounded by a

dotted line. Press OK to proceed with the

selection.

Copy Parameters

Display to Starter

Starter to Display

If the parameter software version in the LCP is different from the software

version of the starter, only Starter to Display will be available.

While the LCP is synchronising, only the OK and OFF buttons are

enabled.

Instructions: Control Panel LCP 501

MI.17.G1.02 - VLT is a registered Danfoss trademark

6. Mounting template

Drill four mounting holes for screws (one in each corner) and two holes for

the DB9 connector.

12.7 mm

177HA613.10

25 mm diameter

25 mm13 mm

136 mm

4 mm diameter

Autres manuels Danfoss Panneau de contrôle

Danfoss

Danfoss ECL Comfort 210 Manuel utilisateur

Danfoss

Danfoss VLT LCP 21 Manuel utilisateur

Danfoss

Danfoss ECL Comfort 100M Manuel utilisateur

Danfoss

Danfoss OPTYMA Control AK-RC 101 Mode d’emploi

Danfoss

Danfoss VLT FC Series Manuel utilisateur

Danfoss

Danfoss VLT LCP 21 Manuel utilisateur

Danfoss

Danfoss VLT LCP 11 Manuel utilisateur

Danfoss

Danfoss ECL Comfort 310 Manuel utilisateur

Danfoss

Danfoss ECL Comfort 210 Manuel utilisateur

Danfoss

Danfoss VLT LCP 11 Manuel utilisateur

Danfoss

Danfoss VLT Control Panel LCP 23 Manuel utilisateur

Danfoss

Danfoss VLT LCP 32 Manuel utilisateur

Danfoss

Danfoss TS715Si Manuel utilisateur

Danfoss

Danfoss AK-RC 113 Manuel utilisateur

Danfoss

Danfoss ECL Comfort 210 Manuel utilisateur

Danfoss

Danfoss VLT DriveMotor FCP 106 Manuel utilisateur

Danfoss

Danfoss VLT FC Series Manuel utilisateur

Danfoss

Danfoss OPX Series Manuel utilisateur

Danfoss

Danfoss VLT LCP 32 Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques